DIN ISO 5610-2-2015 Tool holders with rectangular shank for indexable inserts - Part 2 Style A (ISO 5610-2 2014)《可转位刀片用方柄刀杆 第2部分 A型(ISO 5610-2-2014)》.pdf

1、February 2015 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 25.100.01; 25.060.20!%?cG“2286436www.din.deDDIN ISO 5610-2Tool holders with rectangular shank for indexable inserts Part 2: Style A (ISO 5610-2:2014),English translation of DIN ISO 5610-2:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 2: Form A (ISO 5610-2:2014),Englische berset

3、zung von DIN ISO 5610-2:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 2: Forme A (ISO 5610-2:2014),Traduction anglaise de DIN ISO 5610-2:2015-02SupersedesDIN 4984-2:1987-06www.beuth.deDocument comprises 13 pagesIn case of doubt, the German-language original shall be con

4、sidered authoritative.01.15 Contents PageNational foreword . 31 Scope 52 Normative references . 53 Dimensions 53.1 General 53.2 Tool holder style A for rhombic indexable insert shape C 63.3 Tool holder style A for triangular indexable insert shape T . 84 Designation 105 Material 116 Design 116.1 Typ

5、e of mounting 116.2 Corner radius, r.6.3 Thickness, s, of indexable insert . 117 Extent of delivery . 118 Marking 12Bibliography 13DIN ISO 5610-2:2015-02 2A comma is used as the decimal marker. National Annex NA (informative) Bibliography .411National foreword This document (EN ISO 5610-2:2014) has

6、been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standards Committee Tools a

7、nd Clamping Devices), Working Committee NA 121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of International Standards. Attention is draw

8、n to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank f

9、or indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style T Part 14: Style

10、 H Part 15: Style V The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-2:1987-06 as follows: a) the text of the International Standard has been adopted without any modification.

11、 Previous editions DIN 4984-2: 1980-04, 1987-06 DIN ISO 5610-2:2015-02 3National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DIN 4000-77, Tabular layouts of proper

12、ties Part 77: Inserts, clamped, for grooving, parting and thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal clearance DIN 4967-2, Indexable hardme

13、tal inserts with rounded corners, with partly cylindrical hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool holders with rectangular shank and cart

14、ridges for indexable inserts Presentation of the designation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology of chip removing Reference systems

15、and angles on the cutting part of the tool DIN 6582, Terminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixin

16、g hole Dimensions ISO/TS 13399-201, Cutting tool data representation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular inserts DIN ISO 5610-2:2015-02 4Tool h

17、olders with rectangular shank for indexable inserts Part 2: Style A1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style A, i.e. with straight shank and cutting edge angle r= 90 for side cutting.These tool holders are primarily intended for indexable inserts made of hard

18、metal or other cutting materials intended to be mounted by clamping and used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 561

19、0-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

20、including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is

21、 not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination

22、 angles shown in the figures are recommended values; they can vary according to the application.DIN ISO 5610-2:2015-02 53.2 Tool holder style A for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) l

23、aterally reversed.Figure 1 Tool holder style A for rhombic indexable insert CDIN ISO 5610-2:2015-02 6Table 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.SCACR 0808 068 8 6,4 8,5 8 12 2,38SCACL 0808 06SCACR 1010 0610 10 6,4 10,5 10 12 2,38SCACL 1010 06aFor the selection

24、of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.DIN ISO 5610-2:2015-02 73.3 Tool holder style A for triangular indexable insert shape TK

25、eyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style A for triangular indexable insert TDIN ISO 5610-2:2015-02 8Table 2Dimensions in millimetresSymbolah1js13bh13l3f+050,h2h13l1ak16l2max.sbS

26、TACR 1212 1112 12 11 12,5 12 252,38STACL 1212 11PTANR 1212 113,18PTANL 1212 11CTAPR 1212 11CTAPL 1212 11STACR 1616 1116 16 11 16,5 16 252,38STACL 1616 11PTANR 1616 113,18PTANL 1616 11CTAPR 1616 11CTAPL 1616 11STACR 2020 1620 20 16,5 20,5 20 323,97STACL 2020 16PTANR 2020 164,76PTANL 2020 16CTAPR 2020

27、 163,18CTAPL 2020 16STACR 2525 1625 25 16,5 25,5 25 323,97STACL 2525 16PTANR 2525 164,76PTANL 2525 16CTAPR 2525 163,18CTAPL 2525 16STACR 3225 1632 25 16,5 25,5 32 323,97STACL 3225 16PTANR 3225 164,76PTANL 3225 16CTAPR 3225 163,18CTAPL 3225 16aFor the selection of length, l1, the dash can be replaced

28、 by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.DIN ISO 5610-2:2015-02 9Symbolah1js13bh13l3f+050,h2h13l1ak16l2max.sbSTACR 3232 2232 32 22 33 32 36 4,76STACL 3232 22PTANR 3232

29、22PTANL 3232 22CTAPR 3232 22CTAPL 3232 22STACR 4040 2240 40 22 41 40 36 4,76STACL 4040 22PTANR 4040 22PTANL 4040 22CTAPR 4040 22CTAPL 4040 22aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, s

30、ee ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-2);c) type of mounting, in accordance with ISO 5608

31、;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l

32、1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length l3.EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style A (A), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 10 mm, and width b

33、= 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:Tool holder ISO 5610-2 SCACR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, bore-clamped (P) triangular indexable insert shape T (T), tool holder style A (A), normal clearance of indexab

34、le insert n= 0 (N), right-hand type (R), with height h1= 32 mm, and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 16,5 mm (16) is designated as follows:Tool holder ISO 5610-2 PTANR 3225 P16Table 2DIN ISO 5610-2:2015-02 105 MaterialThe material should be steel with a tens

35、ile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, sha

36、ll then be replaced by the respective symbol for the chosen or agreed-upon type of mounting, in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance wi

37、th this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2 apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 3.Ta

38、ble 3Dimensions in millimetresl3r6,40,41116,50,822NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm and 0,794 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions of l1shall be determined

39、 in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2 apply to indexable inserts without shim and for the standa

40、rd design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryThe tool holders shall be delivered complete with clamping device, but without

41、indexable insert(s).DIN ISO 5610-2:2015-02 118 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of

42、 ISO 5610, i.e. ISO 5610-2:2014, shall be given on the packaging.DIN ISO 5610-2:2015-02 12Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cut

43、ting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool itemsDIN ISO 5610-2:2015-02 13