DIN ISO 5610-5-2015 Tool holders with rectangular shank for indexable inserts - Part 5 Style F (ISO 5610-5 2014)《可转位刀片用方柄刀杆 第5部分 F型(ISO 5610-5-2014)》.pdf

1、February 2015 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 25.100.01; 25.060.20!%?cK“2286440www.din.deDDIN ISO 5610-5Tool holders with rectangular shank for indexable inserts Part 5: Style F (ISO 5610-5:2014),English translation of DIN ISO 5610-5:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 5: Form F (ISO 5610-5:2014),Englische berset

3、zung von DIN ISO 5610-5:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 5: Forme F (ISO 5610-5:2014),Traduction anglaise de DIN ISO 5610-5:2015-02SupersedesDIN 4984-5:1987-06www.beuth.deDocument comprises 13 pagesIn case of doubt, the German-language original shall be con

4、sidered authoritative.01.15A comma is used as the decimal marker. Contents Page National foreword . 3 National Annex NA (informative) Bibliography 4 1 Scope 5 2 Normative references . 5 3 Dimensions . 5 3.1 General . 5 3.2 Tool holder style F for rhombic indexable insert shape C 6 3.3 Tool holder st

5、yle F for triangular indexable insert shape T . 8 4 Designation . 10 5 Material 11 6 Design 11 6.1 Type of mounting . 11 6.2 Corner radius, r. 11 6.3 Thickness, s, of indexable insert 12 7 Extent of delivery 12 8 Marking . 12 Bibliography 13 2DIN ISO 5610-5:2015-02 National foreword This document (E

6、N ISO 5610-5:2014) has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Stan

7、dards Committee Tools and Clamping Devices), Working Committee NA 121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of International Stand

8、ards. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool holders w

9、ith rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13:

10、 Style T Part 14: Style H Part 15: Style V The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-5:1987-06 as follows: a) the text of the International Standard has been adopted wi

11、thout any modification. Previous editions DIN 4984-5: 1980-04, 1987-06 3DIN ISO 5610-5:2015-02 National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DIN 4000-77, Ta

12、bular layouts of properties Part 77: Inserts, clamped, for grooving, parting and thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal clearance DIN 4

13、967-2, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool holders with rec

14、tangular shank and cartridges for indexable inserts Presentation of the designation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology of chip remo

15、ving Reference systems and angles on the cutting part of the tool DIN 6582, Terminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded corners, with p

16、artly cylindrical fixing hole Dimensions ISO/TS 13399-201, Cutting tool data representation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular inserts 4DIN IS

17、O 5610-5:2015-02 Tool holders with rectangular shank for indexable inserts Part 5: Style F1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style F, i.e. with offset shank and cutting edge angle r= 90 for end cutting.These tool holders are primarily intended for indexable i

18、nserts made of hard metal or other cutting materials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are

19、 given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the refe

20、renced document (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimension

21、s3.1 GeneralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angle

22、s and inclination angles shown in the figures are recommended values; they can vary according to the application.5DIN ISO 5610-5:2015-02 3.2 Tool holder style F for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE The figure shows a right-hand tool holder (R); left-hand t

23、ool holder (L) laterally reversed.Figure 1 Tool holder style F for rhombic indexable insert C6DIN ISO 5610-5:2015-02 Table 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.SCFCR 0808 068 8 6,4 10 8 12 2,38SCFCL 0808 06SCFCR 1010 0610 10 6,4 12 10 12 2,38SCFCL 1010 06aFor t

24、he selection of length,l1, the dash can be replaced by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.7DIN ISO 5610-5:2015-02 3.3 Tool holder style F for triangular indexable insert

25、shape TKeyaInclination angle, s.bRake angle, o.8DIN ISO 5610-5:2015-02 NOTE The figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style F for triangular indexable insert TTable 2Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,

26、h13 k16 max.STFCR 1212 1112 12 11 16 12 252,38STFCL 1212 11PTFNR 1212 113,18PTFNL 1212 11CTFPR 1212 11CTFPL 1212 11STFCR 1616 1116 16 11 20 16 252,38STFCL 1616 11PTFNR 1616 113,18PTFNL 1616 11CTFPR 1616 11CTFPL 1616 11STFCR 1616 1616 16 16,5 20 16 323,97STFCL 1616 16PTFNR 1616 164,76PTFNL 1616 16CTF

27、PR 1616 163,18CTFPL 1616 16STFCR 2020 1620 20 16,5 25 20 323,97STFCL 2020 16PTFNR 2020 164,76PTFNL 2020 16CTFPR 2020 163,18CTFPL 2020 16STFCR 2525 1625 25 16,5 32 25 323,97STFCL 2525 16PTFNR 2525 164,76PTFNL 2525 16CTFPR 2525 163,18CTFPL 2525 16aFor the selection of length,l1, the dash can be replac

28、ed by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.9DIN ISO 5610-5:2015-02 Symbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.STFCR 2525 2225 25 22 32 25 36 4,76STFCL 2525 22PTFNR 2

29、525 22PTFNL 2525 22CTFPR 2525 22CTFPL 2525 22STFCR 3225 1632 25 16,5 32 32 323,97STFCL 3225 16PTFNR 3225 164,76PTFNL 3225 16CTFPR 3225 163,18CTFPL 3225 16STFCR 3225 2232 25 22 32 32 36 4,76STFCL 3225 22PTFNR 3225 22PTFNL 3225 22CTFPR 3225 22CTFPL 3225 22STFCR 3232 2232 32 22 40 32 36 4,76STFCL 3232

30、22PTFNR 3232 22PTFNL 3232 22CTFPR 3232 22CTFPL 3232 22STFCR 4040 2240 40 22 50 40 36 4,76STFCL 4040 22PTFNR 4040 22PTFNL 4040 22CTFPR 4040 22CTFPL 4040 22PTFNR 4040 2740 40 27,5 50 40 40 6,35PTFNL 4040 27aFor the selection of length,l1, the dash can be replaced by the dimensions of ISO 5610-1:2010,

31、Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. IS

32、O 5610-5);Table 210DIN ISO 5610-5:2015-02 c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbo

33、l for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style F (F), for normal clear

34、ance of indexable insert n= 7 (C), right-hand type (R), with height h1= 10 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:Tool holder ISO 5610-5 - SCFCR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, bore-clamped (P) t

35、riangular indexable insert shape T (T), tool holder style F (F), normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 22 mm (22) is designated as follows:Tool holder ISO 5610-5 - PTFNR

36、 3225 P225 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agr

37、eement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be co

38、nsidered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge lengths, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2 apply to tool holders with indexable in

39、serts having corner radii, r, in accordance with Table 3.11DIN ISO 5610-5:2015-02 Table 3Dimensions in millimetresl3r6,40,41116,50,82227,5 1,2NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm, and 1,191 mm.For indexable inser

40、ts with corner radii r, other than those specified in Table 3, the dimensions of f shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if any.6.3 Thickness, s, of indexable insertThe values for t

41、hickness, s, given in Tables 1 and 2 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Ex

42、tent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations

43、 in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-5:2014, shall be given on the packaging.12DIN ISO 5610-5:2015-02 Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities

44、in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inse

45、rts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items13DIN ISO 5610-5:2015-02