DIN ISO 5610-6-2015 Tool holders with rectangular shank for indexable inserts - Part 6 Style G (ISO 5610-6 2014)《可转位刀片用方柄刀杆 第6部分 G型(ISO 5610-6-2014)》.pdf

1、February 2015 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 25.100.01; 25.060.20!%?cL“2286441www.din.deDDIN ISO 5610-6Tool holders with rectangular shank for indexable inserts Part 6: Style G (ISO 5610-6:2014),English translation of DIN ISO 5610-6:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 6: Form G (ISO 5610-6:2014),Englische berset

3、zung von DIN ISO 5610-6:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 6: Forme G (ISO 5610-6:2014),Traduction anglaise de DIN ISO 5610-6:2015-02SupersedesDIN 4984-6:1987-06www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original shall be con

4、sidered authoritative.01.15A comma is used as the decimal marker. Contents Page National foreword . 3 National Annex NA (informative) Bibliography 4 1 Scope 5 2 Normative references . 5 3 Dimensions . 5 3.1 General . 5 3.2 Tool holder style G for rhombic indexable insert shape C 6 3.3 Tool holder st

5、yle G for triangular indexable insert shape T 7 4 Designation 9 5 Material 10 6 Design 10 6.1 Type of mounting . 10 6.2 Corner radius, r. 10 6.3 Thickness, s, of indexable insert 11 7 Extent of delivery 11 8 Marking . 11 Bibliography . 12 2DIN ISO 5610-6:2015-02 National foreword This document (EN I

6、SO 5610-6:2014) has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standar

7、ds Committee Tools and Clamping Devices), Working Committee NA 121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of International Standard

8、s. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool holders with

9、 rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: St

10、yle T Part 14: Style H Part 15: Style V The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-6:1987-06 as follows: a) the text of the International Standard has been adopted witho

11、ut any modification. Previous editions DIN 4984-6: 1980-04, 1987-06 DIN ISO 5610-6:2015-02 3National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DIN 4000-77, Tabul

12、ar layouts of properties Part 77: Inserts, clamped, for grooving, parting and thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal clearance DIN 4967

13、-2, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool holders with rectan

14、gular shank and cartridges for indexable inserts Presentation of the designation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology of chip removin

15、g Reference systems and angles on the cutting part of the tool DIN 6582, Terminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded corners, with part

16、ly cylindrical fixing hole Dimensions ISO/TS 13399-201, Cutting tool data representation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular inserts DIN ISO 56

17、10-6:2015-02 4Tool holders with rectangular shank for indexable inserts Part 6: Style G1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style G, i.e. with offset shank and cutting edge angle r= 90 for side cutting.These tool holders are primarily intended for indexable ins

18、erts made of hard metal or other cutting materials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are g

19、iven in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the refere

20、nced document (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3

21、.1 GeneralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles

22、and inclination angles shown in the figures are recommended values; they can vary according to the application.DIN ISO 5610-6:2015-02 53.2 Tool holder style G for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE The figure shows a right-hand tool holder (R); left-hand too

23、l holder (L) laterally reversed.Figure 1 Tool holder style G for rhombic indexable insert CTable 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.SCGCR 0808 068 8 6,4 10 8 12 2,38SCGCL 0808 06SCGCR 1010 0610 10 6,4 12 10 12 2,38SCGCL 1010 06aFor the selection of length,l1,

24、 the dash can be replaced by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.DIN ISO 5610-6:2015-02 63.3 Tool holder style G for triangular indexable insert shape TKeyaInclination ang

25、le, s.bRake angle, o.NOTE The figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style G for triangular indexable insert TDIN ISO 5610-6:2015-02 7Table 2Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.STGCR 1212 111

26、2 12 11 16 12 252,38STGCL 1212 11PTGNR 1212 113,18PTGNL 1212 11CTGPR 1212 11CTGPL 1212 11STGCR 1616 1116 16 11 20 16 252,38STGCL 1616 11PTGNR 1616 113,18PTGNL 1616 11CTGPR 1616 11CTGPL 1616 11STGCR 1616 1616 16 16,5 20 16 323,97STGCL 1616 16PTGNR 1616 164,76PTGNL 1616 16CTGPR 1616 163,18CTGPL 1616 1

27、6STGCR 2020 1620 20 16,5 25 20 323,97STGCL 2020 16PTGNR 2020 164,76PTGNL 2020 16CTGPR 2020 163,18CTGPL 2020 16STGCR 2525 1625 25 16,5 32 25 323,97STGCL 2525 16PTGNR 2525 164,76PTGNL 2525 16CTGPR 2525 163,18CTGPL 2525 16STGCR 2525 2225 25 22 32 25 36 4,76STGCL 2525 22PTGNR 2525 22PTGNL 2525 22CTGPR 2

28、525 22CTGPL 2525 22aFor the selection of length,l1, the dash can be replaced by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.DIN ISO 5610-6:2015-02 8Symbolah1b l3f h2l1al2sbjs13 h1

29、3 +050,h13 k16 max.STGCR 3225 1632 25 16,5 32 32 323,97STGCL 3225 16PTGNR 3225 164,76PTGNL 3225 16CTGPR 3225 163,18CTGPL 3225 16STGCR 3225 2232 25 22 32 32 36 4,76STGCL 3225 22PTGNR 3225 22PTGNL 3225 22CTGPR 3225 22CTGPL 3225 22STGCR 3232 2232 32 22 40 32 36 4,76STGCL 3232 22PTGNR 3232 22PTGNL 3232

30、22CTGPR 3232 22CTGPL 3232 22STGCR 4040 2240 40 22 50 40 36 4,76STGCL 4040 22PTGNR 4040 22PTGNL 4040 22CTGPR 4040 22CTGPL 4040 22PTGNR 4040 2740 40 27,5 50 40 40 6,35PTGNL 4040 27PTGNR 5050 2750 50 27,5 60 50 40 6,35PTGNL 5050 27aFor the selection of length,l1, the dash can be replaced by the dimensi

31、ons of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this p

32、art of ISO 5610 (i.e. ISO 5610-6);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;Table 2DIN ISO 5610-6:2015-02 9f) symbol for the indexable insert normal clearance, in accordance

33、 with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style

34、G (G), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 10 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:Tool holder ISO 5610-6 - SCGCR 1010 E06EXAMPLE 2 Tool holder for a horizontally moun

35、ted, bore-clamped (P) triangular indexable insert shape T (T), tool holder style G (G), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 22 mm (22) is designated as follows:Too

36、l holder ISO 5610-6 - PTGNR 3225 P225 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufactu

37、rers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting, in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable inser

38、t thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge lengths, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to t

39、ool holders with indexable inserts having corner radii, r, in accordance with Table 3.DIN ISO 5610-6:2015-02 10Table 3Dimensions in millimetresl3r6,40,41116,50,82227,5 1,2NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm, and

40、 1,191 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions of l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness, s

41、, of indexable insertThe values for thickness, s, given in Tables 1 and 2 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or

42、 upon delivery (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers di

43、scretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-6:2014, shall be given on the packaging.DIN ISO 5610-6:2015-02 11Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dime

44、nsions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 I

45、SO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool itemsDIN ISO 5610-6:2015-02 12