DIN ISO 702-1-2010 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Part 1 Conical connection (ISO 702-1 2009)《机床 主轴端部和工件夹盘的连接尺寸 第1部分 圆锥连接》.pdf

1、April 2010 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、5.060.20!$aA“1623090www.din.deDDIN ISO 702-1Machine tools Connecting dimensions of spindle noses and work holding chucks Part 1: Conical connection (ISO 702-1:2009)English translation of DIN ISO 702-1:2010-04Werkzeugmaschinen Spindelkpfe und Drehfutter, Anschlussmae Teil 1: Kurzkegelaufnahme mit Sch

3、rauben von vorne (ISO 702-1:2009)Englische bersetzung von DIN ISO 702-1:2010-04Machines-outils Dimensions dassemblage des nez de broche et des mandrins porte-pices Partie 1: Assemblage conique (ISO 702-1:2009)Traduction anglaise de DIN ISO 702-1:2010-04supersedesDIN 55028:1980-03;supersedesDIN 55026

4、:1980-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.DIN ISO 702-3:2010-04,Together withDocument comprises 9 pages03.10 DIN ISO 702-1:2010-04 2 A comma is used as the decimal marker. Contents Page National foreword 2 1 Scope 4 2 Interchangeability 4 3

5、Sizes for interchangeability4 3.1 Spindle noses.4 3.2 Connecting face dimensions8 National foreword This standard has been prepared by Technical Committee ISO/TC 39 “Machine tools”, Subcommittee SC 8 “Work holding spindles and chucks”. The responsible German body involved in its preparation was the

6、Normenausschuss Werkzeuge und Spannzeuge (Tools and Clamping Devices Standards Committee), Working Committee NA 121-02-07 AA Drehmaschinenspannzeuge und Zubehr. Following a proposal of the German Working Committee, ISO 702-1 has been editorially harmonized with ISO 702-2, ISO 702-3 and ISO 702-4. Al

7、l four ISO Standards have been adopted as DIN ISO Standards and published as a series. This third edition cancels and replaces the second edition (ISO 702-1:2001), Tables 1 and 2 and Figures 1 and 2 of which have been technically revised. DIN ISO 702 consists of the following parts, under the genera

8、l title Machine tools Connecting dimensions of spindle noses and work holding chucks: Part 1: Conical connection Part 2: Camlock type Part 3: Bayonet type Part 4: Cylindrical connection DIN ISO 702-1 supersedes DIN 55026 and, together with DIN ISO 702-3, supersedes DIN 55028. Spindle nose types A, B

9、 and C previously specified in DIN 55028 have been replaced and are now dealt with in DIN ISO 702-1 (types A and B) and DIN ISO 702-3 (type C). With the publication of the DIN ISO 702 series of standards, DIN 55026 and DIN 55028 have been withdrawn. Attention is drawn to the possibility that some of

10、 the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 55026:1980-03 and DIN 55028:1980-03 as follows: a) The standard has been completely revised and brought into

11、line with the current state of technology. b) Drawings and dimensioning have been revised and brought into line with the current rules of presentation. c) The tables have been revised accordingly. Previous editions DIN 55026: 1980-03 DIN 55028: 1980-03 DIN ISO 702-1:2010-04 3 1 Scope This part of IS

12、O 702 specifies the sizes for interchangeability of conical spindle noses and corresponding connecting faces of face plates or work holding chucks. NOTE The “camlock type”, “bayonet type” and “cylindrical connection” are specified in ISO 702-2, ISO 702-3 and ISO 702-4, respectively. 2 Interchangeabi

13、lity In this part of ISO 702, all dimensions and tolerances are expressed in millimetres. Although there are differences in the values of dimensions and assembly screws in metric and inch series, the connecting dimensions in Tables 1 and 2 allow for interchangeability between metric- and inch-based

14、chucks (see also footnote “a” in Table 2). 3 Sizes for interchangeability 3.1 Spindle noses See Figure 1 and Table 1. Type A1: Two bolt circles of diameter d2and d3; Type A2: One outer bolt circle of diameter d3(Type A2 for Nos. 3 and 4; types A1 and A2 for Nos. 5 to 28). DIN ISO 702-1:2010-04 4 Mac

15、hine tools Connecting dimensions of spindle noses and work holding chucks Part 1: Conical connection Figure 1 (continued) DIN ISO 702-1:2010-04 5 Key 1 size No. 3 2 size No. 4 3 size Nos. 5 to 11 4 size Nos. 15 to 28 aAll fixing holes. Figure 1 Spindle noses DIN ISO 702-1:2010-04 6 Table 1 Dimension

16、s of spindle noses No. Dimension 3 4 5 6 8 11 15 20 28 nom. 53,975 63,513 82,563 106,375 139,719 196,869 285,775 412,775 584,225 d1tol.0,0080+0,0080+0,0100+0,0100+0,0120+0,0140+0,0160+0,0200+0,0230+d2 61,9 82,6 111,1 165,1 247,6 368,3 530,2 d370,6 82,6 104,8 133,4 171,4 235 330,2 463,6 647,6 d492 10

17、8 133 165 210 280 380 520 725 d5M10 M10 M10 M12 M16 M20 M24 M24 M30 d6H8/h8 14,25 15,9 19,05 23,8 28,6 34,9 41,3 50,8 l1(Type A1) 00,025 14,288 15,875 17,462 19,050 20,638 22,225 25,400 l1(Type A2) 11 11 13 14 16 18 19 21 24 l216 20 22 25 28 35 42 48 56 l3 5 5 5 6 8 8 8 8 l414 17 19 22 25 32 37 42 5

18、0 w and x 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3 NOTE The general tolerance for untoleranced dimensions is 0,4 mm. DIN ISO 702-1:2010-04 7 3.2 Connecting face dimensions See Figure 2 and Table 2. a) With inner bolt circle (for mounting on spindle nose A1 by means of its inner bolt circle) b) With outer

19、 bolt circle (for mounting on spindle nose A1, or spindle nose A2 by means of its outer bolt circle) Figure 2 Connecting face dimensions DIN ISO 702-1:2010-04 8 Table 2 Connecting face dimensions No. Dimension 3 4 5 6 8 11 15 20 28 d153,975 63,513 82,563 106,375 139,719 196,869 285,775 412,775 584,2

20、25 tol. Type 1 a0,0030,005+0,0030,005+0,0040,006+0,0040,006+0,0040,008+0,0040,010+0,0040,012+0,0050,015+0,0060,017+tol. Type 2 a0,0080+0,0080+0,0100+0,0100+0,0120+0,0140+0,0160+0,0200+0,0300+d2 61,9 82,6 111,1 165,1 247,6 368,3 530,2 d370,6 82,6 104,8 133,4 171,4 235 330,2 463,6 647,6 d492 108 133 1

21、65 210 280 380 520 725 d512 12 12 14 18 22 25,5 b27 b33 d60,10+ 14,7 16,3 19,45 24,2 29,4 35,7 42,1 51,6 l1(Type A1) 0,0250+ 14,288 15,875 17,462 19,050 20,638 22,225 25,400 l1min.(Type A2) c 15 16 18 20 21 23 26 l210 10 12 13 14 16 17 19 22 l3 6,5 6,5 6,5 8 10 10 10 10 w and x 0,2 0,2 0,2 0,2 0,2 0

22、,2 0,3 0,3 0,3 NOTE The general tolerance for untoleranced dimensions is 0,4 mm. aType identification shall be marked. bThese are compromise dimensions to allow for interchangeability between inch and metric chucks. cl1of Type A1 may be used in place of l1of Type A2 only if the face plate is rigid enough not to cause bending when the screws are tightened on the inner bolt circle. DIN ISO 702-1:2010-04 9