DIN ISO 8116-5-2009 Textile machinery and accessories - Beams for winding - Part 5 Sectional beams for warp knitting machines (ISO 8116-5 2008) English version of DIN ISO 8116-5 20.pdf

1、August 2009DEUTSCHE NORM English price group 6No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 59.120.30!$Y93“1542216ww

2、w.din.deDDIN ISO 8116-5Textile machinery and accessories Beams for winding Part 5: Sectional beams for warp knitting machines (ISO 8116-5:2008)English version of DIN ISO 8116-5:2009-08Textilmaschinen und Zubehr Kettbume Teil 5: Teilkettbume fr Wirkmaschinen (ISO 8116-5:2008)Englische Fassung DIN ISO

3、 8116-5:2009-08SupersedesDIN ISO 8116-5:1997-05www.beuth.deDocument comprises 7 pagesDIN ISO 8116-5:2009-08 2 Contents Page National foreword .2 National Annex NA (informative) Bibliography 3 1 Scope 4 2 Normative references 4 3 Main dimensions4 4 Mechanical strength 6 5 Circular axial run-out toler

4、ance, Ta, of flanges.6 6 Total run-out tolerance, Tr, of barrel 6 7 Residual imbalance .6 8 Taper reception6 9 Other specifications 7 10 Designation 7 Bilder Figure 1 Sectional beam5 Figure 2 Taper reception .7 Tabellen Table 1 Main dimensions.5 Table 2 Permissible circular axial run-out tolerance o

5、f flanges .6 National foreword This standard has been prepared by Technical Committee ISO/TC 72 “Textile machinery and accessories”, Subcommittee SC 3 “Machinery for fabric manufacturing including preparatory machinery and accessories”. The responsible German body involved in its preparation was the

6、 Normenausschuss Textil und Textil-maschinen (Textilnorm) (Textiles and Textile Machinery Standards Committee (Textilnorm), Technical Committee NA 106-02-04 AA Spulerei und Kettvorbereitungsmaschinen. Attention is drawn to the possibility that some of the elements of this document may be the subject

7、 of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. DIN ISO 8116 consists of the following parts, under the general title Textile machinery and accessories Beams for winding: Part 1: General vocabulary Part 2: Warpers beams Part 3: Weavers beams DIN IS

8、O 8116-5:2009-08 3 Part 4: Test methods and quality classification of flanges for weavers beams, warpers beams and sectional beams Part 5: Sectional beams for warp knitting machines Part 6: Beams for ribbon weaving and ribbon knitting Part 7: Beams for dyeing slivers, rovings and yarns Part 8: Defin

9、itions of run-out tolerances and methods of measurement Part 9: Dyeing beams for textile fabrics The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 286-2 DIN ISO 286-2 ISO 1940-1 DIN ISO 1940-1 ISO 8116-4 DIN ISO 8116-4 ISO 8116-8 DIN ISO

10、8116-8 Amendments This standard differs from DIN ISO 8116-5:1997-05 as follows: a) Some values in Table 1 have been corrected and d1= 815 mm has been deleted. b) Clause 8 “Taper reception” has been added. c) The mechanical strength of sectional beams is to be verified in accordance with ISO 8116-4.

11、Previous editions DIN 64513: 1960-11 DIN 64513-1: 1973-10 DIN ISO 1025: 1982-03 DIN ISO 8116-5: 1989-03, 1997-05 National Annex NA (informative) Bibliography DIN ISO 286-2, ISO system of limits and fits Tables of standard tolerance grades and limit deviations for holes and shafts DIN ISO 1940-1, Mec

12、hanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances DIN ISO 8116-4, Textile machinery and accessories Beams for winding Part 4: Test methods and quality classification of flanges for weavers beams, warpers

13、 beams and sectional beams DIN ISO 8116-8, Textile machinery and accessories Beams for winding Part 8: Definitions of run-out tolerances and methods of measurement 1 Scope This part of ISO 8116 specifies the main dimensions, mechanical strength, designation and permissible values of tolerances of fo

14、rm and position for the main elements of sectional beams for warp knitting machines. For cases where a limit must be fixed for the residual imbalance, a recommendation is made for the choice of quality grade. 2 Normative references The following referenced documents are indispensable for the applica

15、tion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes a

16、nd shafts ISO 1940-1, Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances ISO 8116-4, Textile machinery and accessories Beams for winding Part 4: Test methods and quality classification of flanges for w

17、eavers beams, warpers beams and sectional beams ISO 8116-8, Textile machinery and accessories Beams for winding Part 8: Definitions of run-out tolerances and methods of measurement 3 Main dimensions The main dimensions of the sectional beams are given and explained in Figure 1. The main dimensions o

18、f the sectional beams given in Table 1 shall be met. Textile machinery and accessories Beams for winding Part 5: Sectional beams for warp knitting machines 4 DIN ISO 8116-5:2009-08 Key d1flange diameter d2outside barrel diameter d3bore diameter of flange l1length between flanges l2overall length b w

19、idth of keyway h d3+ keyway depth Figure 1 Sectional beam Table 1 Main dimensions Dimensions in millimetres d1 3 l2 1 d2amin d3H11bb min h min 355 355 535 110 70,4 14,2 75 532 535 1 065 1 270 1 325 196 762 298 1 000 1 065 1 270 1 325 360 152,7 19,6 165,3 aMinimum values depending on the setting devi

20、ce of the machine. bStandard tolerance grades and limit deviations in accordance with ISO 286-2. 5 DIN ISO 8116-5:2009-08 4 Mechanical strength The mechanical strength of sectional beams for knitting machines is classified in accordance with the quality classes defined in ISO 8116-4. The mechanical

21、strength of sectional beams for knitting machines shall be verified, depending on the quality class, by the test method given in ISO 8116-4. 5 Circular axial run-out tolerance, Ta, of flanges The permissible circular axial run-out tolerance, Ta, of flanges given in with Table 2 shall be met. The run

22、-out tolerance shall be measured in accordance with ISO 8116-8. Table 2 Permissible circular axial run-out tolerance of flanges d1mm Tamm 335 0,2 532 0,35 762 0,5 1 000 0,75 6 Total run-out tolerance, Tr, of barrel The permissible total run-out tolerance, Tr, of the barrel shall be measured in milli

23、metres and calculated using Equation (1): 1r0,251000lT= (1) The run-out tolerance shall be measured in accordance with ISO 8116-8. 7 Residual imbalance Depending on the circumstances, it may be necessary to fix a value for the residual imbalance of sectional beams. In general, a quality grade G 6,3

24、in accordance with ISO 1940-1 will be appropriate. If special conditions call for another grade, this shall be specified. 8 Taper reception At a flange diameter, d1, of 762 mm or greater, the sectional beam may be designed with a taper reception as given in Figure 2 in order to achieve a better cent

25、ring on mandrel. 6 DIN ISO 8116-5:2009-08 Figure 2 Taper reception 9 Other specifications The following details should be specified as appropriate: a) materials of the barrel and flanges; b) nature of the material to be wound; c) fabrication process of the sectional beam flanges (casting or forging)

26、; d) surface quality and, if possible, the treatment (paint, chromium-plating, nickel-plating, etc.) of the beam in contact with the material to be wound (inner sides of the flanges and the surface of the outside barrel diameter); e) number of grooves (one or two) to be included in the boss of each

27、flange; f) taper reception (if received). 10 Designation The designation of a sectional beam in accordance with this part of ISO 8116 shall include the following information in the order given: a) “Sectional beam”; b) reference to this part of ISO 8116, i.e. ISO 8116-5; c) flange diameter, d1, in mi

28、llimetres; d) overall length, l2, in millimetres; e) quality class Q1, Q2, Q3 or Q4 in accordance with ISO 8116-4. EXAMPLE A sectional beam for warp knitting machines with flange diameter d1= 535 mm and overall length l2= 1 065 mm with the quality class Q4 shall be designated as follows: Sectional beam ISO 8116-5 - 535 1 065-Q4 7 DIN ISO 8116-5:2009-08