DIN ISO 8489-2-1997 Textile machinery and accessories - Cones for cross winding - Part 2 Dimensions tolerances and designation of cones with half angle 3 30 (ISO 8489-2 1995)《纺织机械和.pdf

1、DEUTSCHE NORM Mav 1997 Textile machinery and accessories Part 2: Dimensions, tolerances and designation of cones Cones for cross winding with a half angle of 3“ 30 (IS0 8489-2 : 1995) DIN IS0 8489-2 ICs 59.120.20 Descriptors: Textile machinery, winding, cones, dimensions. Supersedes DIN IS0 112, Mar

2、ch 1984 edition. Textilmaschinen und Zubehr - Kegelige Hlsen - Teil 2: Mae, Toleranzen und Bezeichnung von Hlsen mit halbem Kegelwinkel 3“ 30 (IS0 8489-2 : 1995) This standard incorporates International Standard IS0 8489-2 Textile machinery and accessories - Conesfor cross winding - Part 2: Dimensio

3、ns, tolerances and designation of cones with half angle 3“ 30. A comma is used as the decimal marker. National foreword This standard has been prepared by ISO/TC 72. The responsible German body involved in its preparation was the Normenausschu Textil und Textil- maschinen (Textiles and Textile Machi

4、nery Standards Committee), Technical Committee Spulerei und Kettvorbereitungsmaschinen. DIN IS0 286-1 and DIN IS0 8489-1 are the standards corresponding to International Standards IS0 286-1 and IS0 8489-1, respectively, referred to in clause 2 of the IS0 Standard. Amendments This standard supersedes

5、 DIN IS0 112, March 1984 edition, and contains the following amendments: a) The cone diameters of 36 mm, 58 mm and 105 mm, and some cone lengths have been dropped. b) The standard has been editorially revised. Previous editions DIN TEX 461 7: 1933-09; DIN 6461 7: 1942-07, 1958-1 O, 1969-03; DIN 6442

6、0-2: 1976-04; DIN IS0 112: 1984-03. National Annex NA Standard referred to (and not included in Normative references) DIN IS0 8489-1 Textile machinery and accessories - Cones for cross winding - Part 1 : Recommended main dimensions (IS0 8489-1 : 1995) IS0 Standard comprises 6 pages. No pari of this

7、standard may be reproduced without the prior permission of Ref. No. DIN IS0 8489-2 : 1997-0 Y Deutsches Institut fr Normung e. V., Berlin. wth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen). English price group 06 Sales No. 0406 04.99 Page 1 IS0 8489-2

8、 : 1995 Textile machinery and accessories Part 2: Dimensions, tolerances and designation of cones with half angle 3“ 30 Cones for cross winding Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of pr

9、eparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, i

10、n liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publ

11、ication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 8489-2 was prepared by Technical Committee ISO/TC 72, Textile machinery and allied machinery and accessories. Sub- committee SC 2, Winding and preparatory machinery

12、 for fabric manufac- ture. This first edition of IS0 8489-2 cancels and replaces IS0 112:1983, which has been technically revised. IS0 8489 consists of the following parts, under the general title Textile machinery and accessories - Cones for cross wmding: - Part I: Recommended main dimensions - Par

13、t 2: Dimensions, tolerances and designation of cones with half angle 3 degrees 30 angle 4 degrees 20 - Part 3: Dimensions, tolerances and designation of cones with half - Part 4: Dimensions, tolerances and designation of cones with half angle 4 degrees 20 for winding for dyeing purposes angle 5 degr

14、ees 57 - Part 5: Dimensions, tolerances and designation of cones with half Page 2 IS0 8489-2 : 1995 1 Scope This part of IS0 8489 specifies the main dimensions, tolerances and designation of cones for cross winding with a half angle of cone 3“ 30. Furthermore, directives are given for the characteri

15、stics of cones and for the control of the diameters and lengths of the cone. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 8489. At the time of publication, the editions indicated were valid. All sta

16、ndards are subject to revision, and parties to agreements based on this part of IS0 8489 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 286-

17、1 :I 988, IS0 system of limits and fits - Part I: Bases of tolerances, deviations and fits. IS0 8489-1 :I 995, Textile machinery and accessories - Cones for cross winding - Part 7: Recommended main dimensions. Page 3 IS0 8489-2 : 1995 3 Dimensions and tolerances See figure 1 a), b) and c) and table

18、1. I Il X a) ODen-ended cone - Type A I- l Dimensions in millirnetres b) Cone with rolled-in top - Type B X ing groove _ILTai1 (optional) c) Cone with flat-end top - Type C Figure 1 - Cones Page 4 IS0 8489-2 : 1995 tolerance Table 1 - Dimensions Dimensions in millimetres 4 *) 1 nominal I tolerance 1

19、 noinai I nominal I tolerance nominal f 0.2 k 0.2 33 17 f 0,s 8 175“ f 13 30 f 0,s 8 175 - + 1.5 46“ rt 0.25 f 0.25 62 - 10 290 f 25 10 340 - + 2,5 - - - 71.5“) 80 d tolerance I nominal f0,2 E k 0.25 E f 0,2 I 25 I fO,5 I 8 I 230 I k 2 f 0,2 I 17 I f 0,5 I 10 1 290 I f 2,5 f 0,2 I 33 I k 0,5 I 8 I 2

20、30“ I k 2 f 0.2 I 25 I f 0.5 I 10 I 290 1 f 2.5 NOTES 1) The width of wound yarn shall not exceed 1 - 25 rnrn. 2) The deviations from the nominal value 3“ 30 of the half angle of the cone are limited by the tolerances for d, di and !, as indicated in the table. They do not influence the practical us

21、e of the cones during winding and further processes. *) In certain cases, especially for automatic winding, dimensions of this size must be agreed upon between the interested Darties in relation to the wall thickness. *) Main dimensions as recommended in IS0 8489-1. 4 Characteristics The following d

22、etails shall be specified by the manufacturer: a) cone material (paper or plastic); b) surface treatment (paper: untreated, impregnated or lacquered); c) nature of yarn to be wound; d) thickness of cone wall (corresponding to the nature of the yarn to be wound); e) run-out tolerance (if required); f

23、) details of tailing groove and notch for tail (if required); g) number, size and location of perforations (if required). The minimum distance between the ends of the cone and edges of the nearest holes, if any, shall be 16 mm k 0.5 mm. Page 5 IS0 8489-2 : 1995 5 See figure2 a) and b) and table2. Di

24、mensions, tolerances and use of the gauges Dimensions in millimetres b 1 (b /2) i0.03 oi for open-endedcones- TypeA b) For cones with rolled-in and flat-end tops - Types B and C Figure 2 - Gauges Table 2 - Dimensions Dimensions in millimetres *) In certain cases, especially for automatic winding, di

25、mensions of this size must be agreed upon between the interested parties in relation to the wall thickness. Page 6 IS0 8489-2 : 1995 The inner dimensions of the cone are in accordance with this part of IS0 8489 if the edge of the larger end of the cone, after it has been placed gently on the gauge a

26、nd then pressed firmly home by hand, is between the tolerance marks. To check the smaller diameter of an open-ended cone, it shall be placed firstly with the smaller end on the gauge. The edge of the smaller end of the cone must then lie between the tolerance marks on the corresponding end of the ga

27、uge. 6 Control of cone length To check the tolerances of the length of the cone, a suitable gauge for checking lengths, for example a slide-gauge, must be used. The conical gauges shown cannot be used for this purpose. 7 Designation The designation of a cone for cross winding with a half angle of 3”

28、 30 shall include the following information, in the order given: a) “Cone” b) reference to this part of IS0 8489, .e. IS0 8489-2; c) its type (A, B or Cl; d) its large inner diameter, d, in millimetres; e) its length, 1. in millimetres. EXAM P L E A cone with a half angle of 3“ 30, type B, with a large inner diameter d of 71,5 mm and length 1 of 230 mm shall be designated as follows: Cone IS0 8489-2 - B 713 x 230