DIN ISO 96-1-2017 Textile machinery and accessories - Rings and travellers for ring spinning and ring twisting frames - Part 1 Flange rings T and SF and their travellers (ISO 96-1 .pdf

1、March 2017 English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 59.120.10!%bVr“2635179www.din.deDIN

2、 ISO 96-1Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Part 1: Flange rings T and SF and their travellers (ISO 961:2016),English translation of DIN ISO 96-1:2017-03Textilmaschinen und Zubehr Ringe und Ringlufer fr Ringspinn und Ringzwirnmaschinen T

3、eil 1: Flanschringe T und SF und passende Ringlufer (ISO 961:2016),Englische bersetzung von DIN ISO 96-1:2017-03Matriel pour lindustrie textile Anneaux et curseurs pour machines filer et retordre Partie 1: Anneaux T et SF et leurs curseurs (ISO 961:2016),Traduction anglaise de DIN ISO 96-1:2017-03Su

4、persedesDIN ISO 961:201007www.beuth.deDocument comprises 8 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.02.17 A comma is used as the decimal marker. National foreword 31 Scope . 52 Normative references 53 Terms and definitio

5、ns . 54 Principal dimensions of T- and SF-rings. 55 Travellers .76 Designation of travellers 8Contents PageDIN ISO 96-1:2017-03 2National Annex NA (informative) Bibliography . 4National foreword This standard (ISO 96-1:2016) has been prepared by Technical Committee ISO/TC 72 “Textile machinery and a

6、ccessories”, Subcommittee SC 1 “Spinning preparatory, spinning, twisting and winding machinery and accessories”. The responsible German body involved in its preparation was DIN-Normenausschuss Textil und Textilmaschinen (Textilnorm) (DIN Standards Committee Textiles and Textile Machinery) (Textilnor

7、m), Working Committee NA 106-02-10 AA Spulerei, Spinnereimaschinen und Nonwoven. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. DIN ISO 96, Textile

8、machinery and accessories Rings and travellers for ring spinning and ring twisting frames consists of the following parts: Part 1: Flange rings T and SF and their travellers Part 2: HZ- and J-rings and their travellers The DIN Standard corresponding to the International Standard referred to in this

9、document is as follows: ISO 3 DIN 323-1 Amendments This standard differs from DIN ISO 96-1:2010-07 as follows: a) in Figure 1, height h1does not extend up to the foot, but to the bar; b) in Figure 2, height h2does not extend up to the foot, but to the bar; c) in Table 1, the tolerance for the flange

10、 width b2has been amended; d) in Table 1, the height of 8 mm for h1and h2has been included; e) in Figure 4, the flange width b1has been removed and Figure 3 has been amended so as to be in line with Figure 4; f) Clause 6 has been editorially revised. Previous editions DIN TEX 4000 = DIN 64000: 1931-

11、03 DIN 64000-1: 1962-04, 1963-09 DIN 63801: 1965-05 DIN 63801-1: 1979-07 DIN 64000: 1979-07 DIN EN ISO 96-1: 1993-01, 2010-07 DIN ISO 96-1:2017-03 3 National Annex NA (informative) Bibliography DIN 323-1, Preferred Numbers and Series of Preferred Numbers Basic Values, Calculated Values, Rounded Valu

12、es DIN ISO 96-1:2017-03 4 Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Part 1: Flange rings T and SF and their travellers1 ScopeThis document specifies the principal dimensions of T- and SF-rings, and the mass and tolerance on the mass, of the app

13、ropriate travellers for flange rings employed on ring spinning and ring twisting machines. It also specifies the method of designation of the travellers.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements

14、of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3, Preferred numbers Series of preferred numbers3 Terms and definitionsNo terms and definitions are listed in this docu

15、ment.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at https:/www.iso.org/obp/4 Principal dimensions of T- and SF-ringsThe principal dimensions of

16、T- and SF-rings are illustrated in Figures 1 and 2, and specified in Table 1.Figure 1 Example of a T-ringDIN ISO 96-1:2017-03 5 Figure 2 Example of an SF-ringTable 1 Ring dimensionsDimensions in millimetresT-Ring SF-RingInside diameter dHeight h1Fitting diameter d1Flange width b1Height h2Fitting dia

17、meter d2Flange width b2nominal tolerancea+0,15 0nominal tolerancea+0,2 0,136384042454881000,200,2(50)5154(55)576063(65)7075810d + 700,252,6b3,2c4d81012d + 1200,252,83,8aThe tolerance refers to the diameter d1, respectively d2, excluding any ovality.bThe flange width b1= 2,6 mm was designated previou

18、sly as ring flange No. 1/2.cThe flange width b1= 3,2 mm was designated previously as ring flange No. 1.dThe flange width b1= 4 mm was designated previously as ring flange No. 2.DIN ISO 96-1:2017-03 6 5 Travellers5.1 Examples of travellers appropriate for T- and SF-rings are shown in Figures 3 and 4.

19、Figure 3 Example of a traveller for a T-ring in the running positionFigure 4 Example of a traveller for an SF-ring in the running position5.2 The values for traveller mass are given in Table 2.Traveller mass is taken from the R20 series of preferred numbers in accordance with ISO 3. The range of tra

20、veller mass comprises values from 4 to 900 inclusive.The traveller mass represents the nominal mass, in grams, of 1 000 travellers of the same type. The tolerance on the nominal mass for 1 000 travellers of the same type is 3 %.DIN ISO 96-1:2017-03 7 Table 2 Traveller massMass of traveller (grams pe

21、r 1 000 travellers)4 25 1604,5 28 1805 31,5 2005,6 35,5 2246,3 40 2507,1 45 2808 50 3159 56 35510 63 40011,2 71 45012,5 80 50014 90 56016 100 63018 112 71020 125 80022,4 140 9006 Designation of travellersThe designation on the packing of travellers for the T- and SF-ring includes the following infor

22、mation:a) the denotation “Traveller” (optional);b) a reference to this document, i.e. ISO 96-1 (optional);c) the symbol “T” or “SF” (optional);d) the flange width, b1, in millimetres, of the appropriate ring (optional);e) the manufacturers designation for the traveller style (e.g. “C”, “EL”);f) the

23、wire section symbol (if applicable), e.g. “f ”, “r ” (“f” = flat, “r” = round);g) the traveller mass (see Table 2);h) the traveller material or traveller name if it is other than steel (where this information is omitted, it is assumed that the traveller material is steel);i) the surface finish (optional);j) the appearance (optional).DIN ISO 96-1:2017-03 8