DLA A A 59590 11B A-2010 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 240 X 180 INCH BODY SIZE.pdf

1、INCHPOUND AA59590/11B 11 October 2010 SUPERSEDING A-A-59590/11A 19 January 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .240 X .180 INCH BODY SIZE The General Services Administration has authorized the use of this comme

2、rcial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specific

3、ation sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /11 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) W, D, E Configuration (see table II) Example: AA595

4、90/11BV38 is the PIN for a black anodize finished, 3.8 inch long card holder. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card assembly firmly in its installed position. When the

5、card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 G-rms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and the heat sink surfaces. Material. Unless otherwise specified herein, the card holder m

6、aterials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, in table I, and AA59590. Actuating screw hex drive socket. The across flats dimension for the hex drive socket shall be as

7、 follows: .094 inch (2.38 mm) for mounting options “J“, “N“, “T“, “R“, “V“, and “S“ and 2.5 mm (.098 inch) for mounting options “G“ and “M“. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be 4 to 6 inch-po

8、unds (0.45 to 0.68 N-m). Cold plate slot width dimensions (when applicable). The recommended cold plate slot width to accommodate the circuit card assembly with attached card holder is .210 inch (5.33 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). AMSC N/A FS

9、C 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/11B 2 Inches mm Inches mm Inches mm .08 .180 2.0 4.57 .220 .240 5.59 6.09 .42 10.7 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwi

10、se specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Dimension shall be .20 inch (5.1 mm) maximum on card holders without option “W“ or “D“ and .30 inch (7.6 mm) maximum on card holders with option “W“ or “D“. 4. The across flats

11、dimension for hex drive socket shall be .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting options “G“ and “M“. FIGURE 1. Relaxed and expanded dime

12、nsions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/11B 3 Finish. The finish designator shall be as specified in AA59590. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film

13、), “E“ (electroless nickel), “H“ (hard black anodize), “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ or “R“ (tapp

14、ed 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. See figure 1 for mounting hole spacing requirements. Mounting hole locations (when required). Two mounting holes are required

15、on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements. Ri

16、vet mounting holes. The holes used for rivet mounting shall be .066 to .073 inch (1.68 to 1.85 mm) diameter through holes, countersunk 100 degrees by .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diameter by .130 to .140 inch (3.30 to 3.56 mm) deep. Ri

17、vets. This card holder uses rivet style A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths fo

18、r this specification sheet are listed in table I. TABLE I. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .02 (0.5) Dimension “C“ .005 (0.13) Dimension “D“ .01 (0.3) Without options “W“ or “D“ With options “W

19、“ or “D“ 18 1.8 (45.7) 2.00 (50.8) 2.10 (53.3) .95 (24.1) .40 (10.2) .275 (6.99) 23 2.3 (58.4) 2.50 (63.5) 2.60 (66.0) 1.45 (36.8) .70 (17.8) .370 (9.39) 28 2.8 (71.1) 3.00 (76.2) 3.10 (78.7) 1.95 (49.5) .90 (22.9) .525 (13.3) 30 3.0 (76.2) 3.20 (81.3) 3.30 (83.8) 2.15 (54.6) 1.10 (27.9) .525 (13.3)

20、 33 3.3 (83.8) 3.50 (88.9) 3.6.0 (91.4) 2.45 (62.2) 1.40 (35.6) .525 (13.3) 35 3.5 (88.9) 3.70 (94.0) 3.80 (96.5) 2.65 (67.3) 1.60 (40.6) .525 (13.3) 38 3.8 (96.5) 4.00 (101.6) 4.10 (104.1) 2.95 (74.9) 1.90 (48.3) .525 (13.3) 40 4.0 (101.6) 4.20 (106.4) 4.30 (109.2) 3.15 (80.0) 2.10 (53.3) .525 (13.

21、3) 43 4.3 (109.2) 4.50 (114.3) 4.60 (116.8) 3.45 (87.6) 2.40 (60.9) .525 (13.3) 45 4.5 (114.3) 4.70 (119.4) 4.80 (121.9) 3.65 (92.7) 2.60 (66.0) .525 (13.3) 48 4.8 (121.9) 5.00 (127.0) 5.10 (129.5) 3.95 (100.3) 2.90 (73.7) .525 (13.3) 50 5.0 (127.0) 5.20 (132.1) 5.30 (134.6) 4.15 (105.4) 3.10 (78.7)

22、 .525 (13.3) 53 5.3 (134.6) 5.50 (139.7) 5.60 (142.2) 4.45 (113.0) 3.40 (86.4) .525 (13.3) 58 5.8 (147.3) 6.00 (152.4) 6.10 (154.9) 4.95 (125.7) 3.90 (99.1) .525 (13.3) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Provided by IHSNot for ResaleNo reproduct

23、ion or networking permitted without license from IHS-,-,-AA59590/11B 4 Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1, 2, and 3. Card holders not requiring the options described by table II

24、shall leave the configuration position in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardware options - 1 No added options W 1 and 2 Lockwasher and flat washer E 1 and 3 Screw self-locking element D 1, 2, and 3 Lockwasher, flat washer and screw self-locking element Loc

25、kwasher and flat washer (see figure 2). The use of a lockwasher and flat washer located under the screw head will provide additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and not

26、es). FIGURE 2. Lockwasher and flat washer details. Screw self-locking element (see figure 3). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in

27、 the PIN (see classification and notes). FIGURE 3. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration shall include a suffix “D“ in the PIN (see classification and

28、 notes). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/11B 5 Sourc

29、e of documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil or from the Standardization

30、Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commer

31、cial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be

32、used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsim

33、ile: (858) 7402430 Electronic mail: (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Aven

34、ue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersede the following manufacturers part numbers in table III and on DESC Drawing 84103 (table IV) as shown. The CID PINs listed in table II ar

35、e only for length designator “28“. See table V for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking pe

36、rmitted without license from IHS-,-,-AA59590/11B 6 TABLE III. Commercial part number supersession data. PIN designator AA59590/11 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ C

37、AGE 5BG68 BJ28 416B A2402.80H 3240BA2.80H BN28 416BA A2402.80 3240BA2.80 BT28 416BT A2402.80T0 3240BA2.80T0 BV28 416BS A2402.80T2 3240BA2.80T2 BG28 416BM MA2402.80TM2.5 3240MBA2.80TM2.5 BJ28E 416BL A2402.80HL 3240BA2.80HL BN28E 416BAL A2402.80L 3240BA2.80L BT28E 416BTL A2402.80T0L 3240BA2.80T0L BV28

38、E 416BSL A2402.80T2L 3240BA2.80T2L BG28E 416BML MA2402.80TM2.5L 3240MBA2.80TM2.5L BJ28W 416BLF WA2402.80H 3240WBA2.80H BN28W 416BLFA WA2402.80 3240WBA2.80 BT28W 416BLFT WA2402.80T0 3240WBA2.80T0 BV28W 416BLFS WA2402.80T2 3240WBA2.80T2 BG28W 416BLFM MWA2402.80TM2.5 3240MWBA2.80TM2.5 BJ28D 416BLFL WA2

39、402.80HL 3240WBA2.80HL BN28D 416BLFAL WA2402.80L 3240WBA2.80L BT28D 416BLFTL WA2402.80T0L 3240WBA2.80T0L BV28D 416BLFSL WA2402.80T2L 3240WBA2.80T2L BG28D 416BLFML MWA2402.80TM2.5L 3240MWBA2.80TM2.5L CJ28 416 2402.80H 3240CG2.80H CN28 416A 2402.80 3240CG2.80 CT28 416T 2402.80T0 3240CG2.80T0 CV28 416S

40、 2402.80T2 3240CG2.80T2 CG28 416M M2402.80TM2.5 3240MCG2.80TM2.5 CJ28E 416L 2402.80HL 3240CG2.80HL CN28E 416AL 2402.80L 3240CG2.80L CT28E 416TL 2402.80T0L 3240CG2.80T0L CV28E 416SL 2402.80T2L 3240CG2.80T2L CG28E 416ML M2402.80TM2.5L 3240MCG2.80TM2.5L See footnote at end of table. Provided by IHSNot

41、for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/11B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/11 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 6108

42、1 Vendor similar designator or type part number 1/ CAGE 5BG68 CJ28W 416LF W2402.80H 3240WCG2.80H CN28W 416LFA W2402.80 3240WCG2.80 CT28W 416LFT W2402.80T0 3240WCG2.80T0 CV28W 416LFS W2402.80T2 3240WCG2.80T2 CG28W 416LFM MW2402.80TM2.5 3240MWCG2.80TM2.5 CJ28D 416LFL W2402.80HL 3240WCG2.80HL CN28D 416

43、LFAL W2402.80L 3240WCG2.80L CT28D 416LFTL W2402.80T0L 3240WCG2.80T0L CV28D 416LFSL W2402.80T2L 3240WCG2.80T2L CG28D 416LFML MW2402.80TM2.5L 3240MWCG2.80TM2.5L EJ28 416EN EN2402.80H 3240EN2.80H EN28 416ENA EN2402.80 3240EN2.80 ET28 416ENT EN2402.80T0 3240EN2.80T0 EV28 416ENS EN2402.80T2 3240EN2.80T2

44、EG28 416ENM MEN2402.80TM2.5 3240EN2.80TM2.5 EJ28E 416ENL EN2402.80HL 3240EN2.80HL EN28E 416ENAL EN2402.80L 3240EN2.80L ET28E 416ENTL EN2402.80T0L 3240EN2.80T0L EV28E 416ENSL EN2402.80T2L 3240EN2.80T2L EG28E 416ENML MEN2402.80TM2.5L 3240MEN2.80TM2.5L EJ28W 416ENLF WEN2402.80H 3240WEN2.80H EN28W 416EN

45、LFA WEN2402.80 3240WEN2.80 ET28W 416ENLFT WEN2402.80T0 3240WEN2.80T0 EV28W 416ENLFS WEN2402.80T2 3240WEN2.80T2 EG28W 416ENLFM MWEN2402.80TM2.5 3240MWEN2.80TM2.5 EJ28D 416ENLFL WEN2402.80HL 3240WEN2.80HL EN28D 416ENLFAL WEN2402.80L 3240WEN2.80L ET28D 416ENLFTL WEN2402.80T0L 3240WEN2.80T0L EV28D 416EN

46、LFSL WEN2402.80T2L 3240WEN2.80T2L EG28D 416ENLFML MWEN2402.80TM2.5L 3240MWEN2.80TM2.5L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/11B 8 TABLE III. Commercial part number supersession data Continued. PIN desi

47、gnator AA59590/11 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 HJ28 416B3 HA2402.80H 3240BH2.80H HN28 416B3A HA2402.80 3240BH2.80 HT28 416B3T HA2402.80T0 3240BH2.80T0 HV28 416B3S HA2402.80T2 3240BH2.80T2 HG28 416B3M MHA2402.80TM2.5 32