DLA A A 59590 18B A-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 260 X 260 INCH BODY SIZE WITH VISUAL LOCK INDICATION.pdf

1、INCHPOUND AA59590/18B 18 June 2012 SUPERSEDING AA59590/18A 23 June 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE .260 X .260 INCH BODY SIZE, WITH VISUAL LOCK INDICATION The General Services Administration has authorized t

2、he use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item descri

3、ption (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /18 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) * Configuration Example: AA5959

4、0/18ET58E is the PIN for a nickel plated, 5.8 inches (147 mm) long card holder with a visual lock indication and a screw self-locking element. The card holder also features two tapped 0-80 UNF mounting holes for use with fasteners. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the ci

5、rcuit card assembly firmly in its installed position and provide high resistance to loosening due to shock and vibration. Card holders shall also provide maximum thermal transfer from the circuit card assembly to the cold plate or heat sink surfaces. Interface and physical dimensions. The card holde

6、rs supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4, and table I) and meet the general requirements of CID AA59590. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“ and “V

7、“. The dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Cold plate dimensions. Recommend cold plate slot width to accommodate

8、 the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shal

9、l be as follows: 10 inch-pounds (1.1 N-m) for assemblies using no options or option “W“ and 12 inch-pounds (1.4 N-m) for assemblies using options “D“ or “E“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/18B 2 Inches mm Inc

10、hes mm Inches mm Inches mm Inches mm .20 .25 5.1 6.4 .260 .270 6.60 6.86 .27 .325 6.9 8.26 .39 .56 9.9 14.2 .70 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .01

11、0 inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex drive socket shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“ and “V“. The across flats dimension for hex drive socket shall be a m

12、etric dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions, basic configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/18B 3 Visual lock indicator (see figure 2). The card h

13、older assembly shall have a visual indicator to show when the card holder assembly is in its relaxed (unlocked) state. When the card holder assembly is in the relaxed state, the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder

14、has been tightened so that the assembly is in the expanded (locked) position, this red band shall be concealed. FIGURE 2. Visual lock indicator details. Finish. The finish designator shall be as specified in AA59590. The finishes available for this CID specification sheet are as follows: “B“ (black

15、anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film) Mounting. The mounting designators shall be as specified in AA59590. Except when using mounting option “N“ two mounting holes are required on the card holders. The mounting options av

16、ailable for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UNC 2B holes), or “G“ (tapped M2.5 x.45 metric holes). See figure 1 and table I for mounting hole spacing requirements. Card holders using mo

17、unting option “J“ may be shipped unassembled. Counterbore holes (for rivet mounting). The holes used for rivet mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with an access/clearance counterbore of .156 inch (3.96 mm) d

18、iameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59590 and the lengths available for this CID specification sheet are listed

19、in table I. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “B“ .03 (0.8 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) 2.30 (58.4 mm) .90 (22.9 mm) 38 3.8

20、 (97 mm) 3.30 (83.8 mm) 1.90 (48.3 mm) 48 4.8 (122 mm) 4.30 (109.2 mm) 2.90 (73.7 mm) 58 5.8 (147 mm) 5.30 (134.6 mm) 3.90 (99.1 mm) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted

21、without license from IHS-,-,-AA59590/18B 4 Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. The correct PIN configuration identifier for each o

22、ption is listed in table II. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configuration. Configuration Applicable figures Hardware options 1 and 2 No changes from basic configuration W 1, 2, and 3 Lockwasher and flat

23、washer E 1, 2, and 4 Screw self-locking element D 1, 2, 3, and 4 Lockwasher, flat washer, and screw self-locking element Lockwasher and flat washer (see figure 3). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card hol

24、der assembly from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The use of a screw self-locking element on the scr

25、ew will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classification and notes). FIGURE 4. Screw self-locking element details. Lock

26、washer, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classification and notes). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

27、 IHS-,-,-AA59590/18B 5 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA59590 Holder, Electrical Card, Wedge Retainers, 3 P

28、iece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering

29、data shall be as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacture

30、rs were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name an

31、d address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim,

32、CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table I

33、V for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/

34、18B 6 TABLE III. Commercial part number supersession data. PIN designator AA59590/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28 VA2452.80H 3245VBA2.80H BN28 VA2452.80 3245VBA2.80 BT28 VA2452.80T0 3245VBA2.80T0 BV28 VA2452.80T2 3245VBA2.80T2 BG28 MVA2452.80TM2.5 32

35、45MVBA2.80TM2.5 BJ28W WVA2452.80H 3245VWBA2.80H BN28W WVA2452.80 3245VWBA2.80 BT28W WVA2452.80T0 3245VWBA2.80T0 BV28W WVA2452.80T2 3245VWBA2.80T2 BG28W MWVA2452.80TM2.5 3245MVWBA2.80TM2.5 BJ28E VA2452.80HL 3245VBA2.80HL BN28E VA2452.80L 3245VBA2.80L BT28E VA2452.80T0L 3245VBA2.80T0L BV28E VA2452.80T

36、2L 3245VBA2.80T2L BG28E MVA2452.80TM2.5L 3245MVBA2.80TM2.5L BJ28D WVA2452.80HL 3245VWBA2.80HL BN28D WVA2452.80L 3245VWBA2.80L BT28D WVA2452.80T0L 3245VWBA2.80T0L BV28D WVA2452.80T2L 3245VWBA2.80T2L BG28D MWVA2452.80TM2.5L 3245MVWBA2.80TM2.5L CJ28 V2452.80H 3245VWCG2.80H CN28 V2452.80 3245VWCG2.80 CT

37、28 V2452.80T0 3245VWCG2.80T0 CV28 V2452.80T2 3245VWCG2.80T2 CG28 MV2452.80TM2.5 3245MVWCG2.80TM2.5 CJ28W WV2452.80H 3245VWCG2.80H CN28W WV2452.80 3245VWCG2.80 CT28W WV2452.80T0 3245VWCG2.80T0 CV28W WV2452.80T2 3245VWCG2.80T2 CG28W MWV2452.80TM2.5 3245MVWCG2.80TM2.5 See footnotes at end of table. Pro

38、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/18B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 CJ28E V2452.80HL 3245VCG2.80

39、HL CN28E V2452.80L 3245VCG2.80L CT28E V2452.80T0L 3245VCG2.80T0L CV28E V2452.80T2L 3245VCG2.80T2L CG28E MV2452.80TM2.5L 3245MVCG2.80TM2.5L CJ28D WV2452.80HL 3245VWCG2.80HL CN28D WV2452.80L 3245VWCG2.80L CT28D WV2452.80T0L 3245VWCG2.80T0L CV28D WV2452.80T2L 3245VWCG2.80T2L CG28D MWV2452.80TM2.5L 3245

40、MVWCG2.80TM2.5L EJ28 VEN2452.80H 3245VEN2.80H EN28 VEN2452.80 3245VEN2.80 ET28 VEN2452.80T0 3245VEN2.80T0 EV28 VEN2452.80T2 3245VEN2.80T2 EG28 MVEN2452.80TM2.5 3245MVEN2.80TM2.5 EJ28W WVEN2452.80H 3245VWEN2.80H EN28W WVEN2452.80 3245VWEN2.80 ET28W WVEN2452.80T0 3245VWEN2.80T0 EV28W WVEN2452.80T2 324

41、5VWEN2.80T2 EG28W MWVEN2452.80TM2.5 3245MVWEN2.80TM2.5 EJ28E VEN2452.80HL 3245VEN2.80HL EN28E VEN2452.80L 3245VEN2.80L ET28E VEN2452.80T0L 3245VEN2.80T0L EV28E VEN2452.80T2L 3245VEN2.80T2L EG28E MVEN2452.80TM2.5L 3245MVEN2.80TM2.5L EJ28D WVEN2452.80HL 3245VWEN2.80HL EN28D WVEN2452.80L 3245VWEN2.80L

42、ET28D WVEN2452.80T0L 3245VWEN2.80T0L EV28D WVEN2452.80T2L 3245VWEN2.80T2L EG28D MWVEN2452.80TM2.5L 3245MVWEN2.80TM2.5L See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/18B 8 TABLE III. Commercial part number super

43、session data Continued. PIN designator AA59590/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 HJ28 VHA2452.80H 3245VBH2.80H HN28 VHA2452.80 3245VBH2.80 HT28 VHA2452.80T0 3245VBH2.80T0 HV28 VHA2452.80T2 3245VBH2.80T2 HG28 MVHA2452.80TM2.5 3245MVBH2.80TM2.5 HJ28W WVHA2452

44、.80H 3245VWBH2.80H HN28W WVHA2452.80 3245VWBH2.80 HT28W WVHA2452.80T0 3245VWBH2.80T0 HV28W WVHA2452.80T2 3245VWBH2.80T2 HG28W MWVHA2452.80TM2.5 3245MVWBH2.80TM2.5 HJ28E VHA2452.80HL 3245VBH2.80HL HN28E VHA2452.80L 3245VBH2.80L HT28E VHA2452.80T0L 3245VBH2.80T0L HV28E VHA2452.80T2L 3245VBH2.80T2L HG2

45、8E MVHA2452.80TM2.5L 3245MVBH2.80TM2.5L HJ28D WVHA2452.80HL 3245VWBH2.80HL HN28D WVHA2452.80L 3245VWBH2.80L HT28D WVHA2452.80T0L 3245VWBH2.80T0L HV28D WVHA2452.80T2L 3245VWBH2.80T2L HG28D MWVHA2452.80TM2.5L 3245MVWBH2.80TM2.5L RJ28 VR2452.80HL 3245VCC2.80H RN28 VR2452.80L 3245VCC2.80 RT28 VR2452.80T

46、0L 3245VCC2.80T0 RV28 VR2452.80T2L 3245VCC2.80T2 RG28 MVR2452.80TM2.5L 3245MVCC2.80TM2.5 RJ28W WVR2452.80H 3245VWCC2.80H RN28W WVR2452.80 3245VWCC2.80 RT28W WVR2452.80T0 3245VWCC2.80T0 RV28W WVR2452.80T2 3245VWCC2.80T2 RG28W MWVR2452.80TM2.5 3245MVWCC2.80TM2.5 See footnotes at end of table.Provided

47、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/18B 9 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 RJ28E WVR2452.80H 3245VCC2.80HL RN28E WVR2452.80 3245VCC2.80L RT28E WVR2452.80T0 3245VCC2.80T0L RV28E WVR2452.80T2 3245VCC2.80T2L RG28E MWVR2452.80TM2.5 3245MVCC2.80TM2.5L RJ28D WVR2452.80HL 3245VWCC2.80HL RN28D WVR2452.80L 3245VWCC2.80L RT28D WVR2452.80T0L 3245VWCC2.80T0L RV28D