DLA A A 59832 4-2010 EXTRACTOR ELECTRICAL CARD METAL NON朙OCKING SINGLE ACTION FOR 063 094 AND 125 INCH THICK CIRCUIT CARD ASSEMBLIES.pdf

1、INCHPOUND AA59832/4 28 June 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET EXTRACTOR, ELECTRICAL CARD, METAL, NONLOCKING, SINGLE ACTION, FOR .063, .094, AND .125 INCH THICK CIRCUIT CARD ASSEMBLIES The General Services Administration has authorized the use of this commercial item description fo

2、r all federal agencies. The complete requirements for procuring extractors described herein shall consist of this document and the latest issue in effect of AA59832. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification syst

3、em which is included in the Part Identification Number (PIN) as shown in the following example (see NOTES). AA59832 CID number /04 Applicable CID sheet U Configuration (see table I) * Slot width (see table I) 7 Material P Finish C Color Example: AA59832/04UT7PC is the PIN for a medium length stainle

4、ss steel extractor designed for mounting on a circuit card assembly with a printed board thickness of .094 inch (2.4 mm) in width. The corrosion protection applied to the extractor material is passivate (clear). SALIENT CHARACTERISTICS. Performance. Extractors shall be capable of injecting and remov

5、ing the circuit card assembly from its installed position. Interface and physical dimensions. The extractors supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59832. Configuration. The configuration of a extractor shall be as s

6、pecified in table I and on figure 1. Slot width. The available slot widths needed to accommodate various printed board thicknesses for the extractors covered by this CID specification sheet are specified in table I. Material. The extractor material shall be stainless steel as specified in AA59832. T

7、he material designator shall be a “7“ as specified in AA59832. Finish. The finish designator shall be as specified in AA59832. The only finish available for this CID specification sheet is “P“ (passivate). Color. The color designator shall be as specified in AA59832. The only color available for thi

8、s CID specification sheet is “C“ (clear). AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/4 2 Roll pin. A stainless steel roll pin is furnished with each extractor. The roll pin is .09375 inch (2.38 mm) diameter by .3125 inc

9、h (7.9 mm) long. TABLE I. Configurations and dimensions. 1/ Configuration Slot width designator Slot width Dimension “W“ 2/ Inch (mm) Accommodates printed board thickness Inch (mm) Mounting Dimension “M“ Inch (mm) U S .075 (1.91) .063 (1.6) .40 (10.2) U T .110 (2.79) .094 (2.4) .39 (9.9) U E .140 (3

10、.56) .125 (3.2) .38 (9.7) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. 2/ Tolerance is +.010, .000 inch (+0.25, 0.000 mm). Inches mm Inches mm Inches mm .250 6.35 .345 8.76 1.20 31.0 NOTES: 1. Dimensions are in inches. Millimeter equivalents are g

11、iven for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 1. Configuration U dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

12、 IHS-,-,-AA59832/4 3 Circuit card assembly printed board. The circuit card assembly should be designed so that electronic components in the area around the ejector mounting hole have sufficient clearance for ejector rotation as shown on figure 2. It is recommended that the outer edge of the circuit

13、card assembly be flush with the end of the card guide for the ejector to obtain optimum leverage. A single ejector is recommended for circuit card assemblies up to 5 inches (127 mm) in width. For circuit card assemblies over 5 inches (127 mm) in width or when using an electrical connector with more

14、than 100 contacts, two ejectors mounted on each circuit card assembly is recommended. Inches mm Inches mm Inches mm .109 .200 2.77 5.08 .312 .37 7.92 9.4 .70 17.8 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, toleran

15、ces are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 2 Circuit card assembly printed board mounting dimensions. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classif

16、ication section for PIN format example. Source of documents. Commercial Item Description AA59832 Extractor, Electrical Card, Metal, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/quicksearch/ or from

17、the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/4 4 Ordering data. Ordering data is as specified in AA59832. Commercial products. As part o

18、f the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the require

19、ments of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 07556 Unitrack Industries,

20、 Inc. 967 E. Masten Circle Milford, DE 199631085 Telephone: (302) 4245050 Facsimile: (302) 4245055 Electronic mail: URL: Part number (P/N) supersession data. This CID specification sheet PINs supersede the following manufacturers P/Ns as shown in table II. This information is being provided to ass

21、ist in reducing proliferation in the Government inventory system. TABLE II. Commercial part number supersession data. PIN designator AA59832/4 Vendor similar designator or type part number 1/ CAGE 07556 US7PC L10006SS UT7PC L10009SS UE7PC L100012SS 1/ The manufacturers P/N shall not be used for proc

22、urement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59832. MILITA

23、RY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing Activity: Air Force 85 DLA CC DLA CC Project 59982009049 Review Activity: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/quicksearch/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-