DLA A-A-50452 A-2011 LAMP INCANDESCENT S-6 BAYONET CANDELABRA DOUBLE CONTACT.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or DLA Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you may want to verify the

2、 currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 6240 INCH-POUND A-A-50452A 13 September 2011 SUPERSEDING A-A-50452 24 January 1992 COMMERCIAL ITEM DESCRIPTION LAMP, INCANDESCENT, S-6, BAYONET CANDELABRA, DOUBLE CONTACT The General Services Administ

3、ration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers S-6 incandescent lamps with a bayonet candelabra base. These lamps can be identified by the industry number 6S6DC(120). 2. SALIENT CHARACTERISTICS 2.1 P

4、hysical characteristics. The lamps shall conform to figure 1 and the following physical characteristics: Bulb designation S-6 Bulb finish Clear Base designation Bayonet candelabra, double contact Light center length 1.062 inches (distance from the center of the light source to the top of base pin) D

5、imensions (See figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50452A 2 FIGURE 1. Lamp dimensions (inches). 2.2 Functional characteristics. The lamps shall conform to the following functional characteristics: Volts 120 Watts 6 Lumen out

6、put (approx.) 40 Life hours (approx.) 1500 3. REGULATORY REQUIREMENTS 3.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PR

7、OVISIONS 4.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserv

8、es the right to require proof of such conformance. 4.2 Market acceptability. The products offered must have been previously sold either to the government or on the commercial market. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50452A 3 5. PAC

9、KAGING 5.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specified in the acquisition order (see 6.2(b). 6. NOTES 6.1 Source of document. 6.1.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electron

10、ic copies may be obtained from https:/www.acquisition.gov/far/. 6.2 Ordering data. The acquisition order should specify the following information: a. CID document number, revision, and CID PIN. b. Preservation, packing, and marking (see 5.1) 6.3 Cross-reference data. Cross-reference data for the par

11、t number information for this CID is as follows: CID part number A50452-1 MS-based part number MS15567-1 Industry number 6S6DC(120) 6.4 Subject term (key word) listing. Bulb Filament Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50452A 4 MILITA

12、RY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians: GSA - FAS Army - CR4 Navy - SH Air Force - 99 DLA - GS Review Activities: Air Force - 71 DLA - IS Preparing Activity: DLA - GS2 (Project 6240-2011-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-