DLA A-A-50547-1994 BAG LINEMAN-S GLOVE《架线工手套袋》.pdf

1、A-A-50543 = 9999974 O362279 563 I INCH-POUND I A-A- 50547 Februarv 22. 1994 SUPERSEDING 25 August 1988 MIL-B-28599C(YD) COMMERCIAL ITEM DESCRIPTION BAG, LINEMANS GLOVE This Commercial Item Description (CID) is approved by the Commissioner, Federal Supply Service, General Services Administration, for

2、 the use of all Federal agencies. This CID is to be used in preference to Military Specification MIL-B-28599C(D), which is cancelled. Abstract. storing and protecting linemans gloves. This CID covers the requirements for one type of protective bag for Salient characteristics. i 1. 2. 3. 4. 5. Cloth.

3、 The cloth used in fabrication shall be made from cotton duck single wall, commercial designation No. 8, hard texture. Minimum weight per square yard shall be 23 ounces (oz) (652 grams (g). Thread. Thread used in sewing shall be commercial thread. Thread shall be cotton, polyester, or nylon and shal

4、l have a minimum breaking strength of 14 pounds (lb) (6.35 kilograms (kg). Grommets. The grommets and washers shall be the manufacturers standard brass grommets and washers. Grommets shall be provided in bottom or bottom gusset. Design. and sides, equipped with a rust-resistant snap hook and dee rin

5、g for attachment to a linemans belt. The glove bag shall consist of a body with a gusset bottom Dimensions. The nominal dimensions of the bag shall be overall depth 4 inches (10.2 centimeters (cm), overall height 18 inches (45.7 cm), overall width 9 inches (22.9 cm). IBeneficial comments (recommenda

6、tions, additions, deletions) and any pertinent1 Idata which may be of use in improving this document should be addressed to: I 7 ICommanding Officer (Code 156), Naval Construction Battalion Center, I Il000 23rd Avenue. Port Hueneme, CA 93043-4301. I FSC 4240 rl) DISTRIBUTION STATEMENT A. Approved fo

7、r public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50547 m 9999974 0362280 285 m A-A- 50547 6. Stitchinq. All stitching shall be lock type stitch, 6 to 8 stitches Thread breaks in stitching shall per inch

8、 (2 to 3 stitches per cm). be overstitched not less than 1 inch (2.54 cm) at each break. Stitching shall be backstitched not less than 1 inch (2.54 cm) at the ends except where ends are turned under in a hem or held down by overstitching. stitching. Thread tension shall be maintained to prevent loos

9、e All thread ends shall be trimmed. 7. Seams. so that no runoffs, twists, pleats, puckers, or open seams shall result. Seam allowance shall be maintained with seams properly sewn 8. Settine of grommets. Holes, punched to receive the grommets, shall be smaller than the outside diameter of the grommet

10、 barrel, making it necessary to force the barrel through the hole. securely clinched to avoid cutting of the material. Grommets shall be 9. SDecial markin-;. Each bag shall be stenciled in a clear, legible manner with the words “ALWAYS WEAR YOUR GUIVES.“ Contractor certification. substantiating evid

11、ence that the product offered meets the salient characteristics of this CID and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices and is the same product sold in the commercial marketplace. right to require proof of such conformance p

12、rior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The contractor shall certify and maintain The Government reserves the Metric DrOdUCtS. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured

13、using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of FED-STD-376, and all other requirements of this CID are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in th

14、e inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. officer has the option of accepting or rejecting the product. The contracting Recrulatorv reauirements. In accordance with Section 23.403 of the Federal Acquisition Regulations, the Gov

15、ernments policy is to acquire items composed of the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition without adversely affecting performance requirements or exposing the suppliers employees to undue hazards from the recovered mate

16、rials. Packaeine. Dackinp and marking. The packaging, packing, labeling, and marking shall be as specified in the contract or order. Notes. FED-STD-376 is available from Standardization Documents Order Desk, Bldg. 4D, 700 Rabbins Avenue, Philadelphia, PA 19111-5094. c The only known NSN referencing

17、this document is 4240-00-070-0968. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50547 = 9999974 0162281 111 A-A-50547 MILITARY INTERESTS: a Custodian 1 Navy - YD1 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: Navy - M1 (Project 4240-0588) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-