DLA A-A-52193 F-2008 FOOD CONTAINER INSULATED WITH INSERTS《带插件的隔热食品容器》.pdf

1、INCH-POUND A-A-52193F March 24, 2008 SUPERSEDING A-A-52193E February 18, 2004 COMMERCIAL ITEM DESCRIPTION FOOD CONTAINER, INSULATED, WITH INSERTS The General Services Administration has authorized the use of this commercial item description in preference to MIL-F-10870 for all federal agencies. 1. S

2、COPE AND CLASSIFICATION. 1.1 Scope. This commercial item description (CID) covers plastic insulated food containers with removable insert pans having covers and gaskets for the transportation of hot or cold foods and liquids without spillage (see 6.1). 1.2 Classification The food containers shall be

3、 of the following sizes, types, and classes (see 6.3): Size 1 - 10 1/4 inches height (see 2.1) Size 2 - 12 1/4 inches height (see 2.1) Size 3 - 9 1/4 inches height (see 2.1) Type I - 1/3 size, 6 inches deep, stainless steel insert pans with lids and gaskets (see 2.1.3) Type II - 1/3 size, 6 inches d

4、eep, plastic insert pans with lids and gaskets (see 2.1.4) Type III - Full size, 6 inches deep, plastic insert pans with lid and gasket (see 2.1.4) Class 1 - Brown (Desert Sand) Class 2 - Green (Olive) 1.3 CID based part identification number (PIN). A document based PIN to identify sizes and classes

5、 is included in section 6. This part identification number procedure is for government purposes and does not constitute a requirement for the contractor (see 6.6). 2. SALIENT CHARACTERISTICS. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data which ma

6、y improve this document should be sent to: Defense Supply Center Philadelphia (DSCP), ATTN: DSCP-FTSA, 700 Robbins Avenue, Philadelphia, PA 19111-5096 AMSC N/A FSC 7330 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52193F 2.1 Design. The insula

7、ted food container shall consist of a sealed insulated plastic body and lid. Lids shall be interchangeable between sizes 1 and 2. The exterior of the food container shall have an integral molded hand grasp handle which is continuous around the outside edge, and a minimum of four, over-the-center, pl

8、astic, lid locking latches. The food containers shall have the following maximum outside dimensions: Width Length HeightSize (inches) (inches) (inches)1 17 3/8 25 1/8 10 1/4 2 17 3/8 25 1/8 12 1/4 3 16 5/8 24 3/8 9 1/4 The food containers shall be stackable with an indentation in each outside corner

9、 of the lid to accommodate matching pads on the bottom of each container body. The stack ability interface shall be dimensionally the same for each size container. Size 1 and 2 containers shall be stackable when sizes are mixed in the same stack. The size 3 food container shall be nestable with a re

10、cessed bottom half of the body to accommodate matching insulated food containers. The nest ability interface shall be dimensionally the same for each size 3 container and shall reduce the stowage volume by more than or equal to 25% when two or more containers are nested together as compared to being

11、 stacked. 2.1.1 Body. The insulated container body shall consist of an inner and outer shell made of high density plastic, which is NSF/ANSI Standard 2, and Food and Drug Administration (FDA) food grade approved; also insulated to comply with the temperature performance specified in 2.2. The interio

12、r shall accommodate one full size, or three, one-third size, steam table pans, 6 inches deep. The size 1 container interior shall accommodate three tray pack cans (see figure 1). The size 2 container interior shall accommodate four tray pack cans (see figure 1). The size 3 container interior shall a

13、ccommodate five tray pack cans(see figure1). The body shall have a minimum of four plastic over-the-center latches. Latches shall be attached using stainless steel (American Iron and Steel Institute (AISI) types 304L or 316) machine screws threaded into the body. The latches shall be recessed from t

14、he outside edge of the body in both the latched and unlatched positions. Latches shall clamp the lid sufficiently to meet the thermal requirements specified in section 2.2. 2.1.2 Lid. The insulated lid shall be sealed, double walled, and made of high density plastic, which is Food and Drug Administr

15、ation (FDA) food grade approved, and insulated to comply with the temperature performance specified in 2.2. The top surface of the lid shall have recessed latching depressions to accommodate the latches installed on the body. The interior of the lid shall have special ribs to match the locations of

16、the insert cover gaskets. When latched closed, the lid shall compress the insert cover gasket to form a liquid-tight seal on each insert pan. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52193F 2.1.3 Stainless steel insert pans type I. The i

17、nsert pans (3 required) shall be 22 gauge (U.S. Standard Gauge shall apply to all sheet metal thicknesses) AISI type 304 stainless steel. Insert pans shall have NSF/ANSI Standard No. 2 1isting. Each pan (6 by 11-5/8 inch inside dimensions) shall have a smooth bead around the top edge for easy cleani

18、ng and sealing. All inside corners shall be rounded and the flange (1/4 inch all around pan) shall have a minimum of 1/16-inch flat, horizontal termination around the trimmed edge to strengthen the flange on the pan. Pans shall be supplied with a 20 gauge passivated stainless steel cover and molded

19、gasket to seal the pan from liquid leakage. The gasket shall meet all FDA regulations for articles having repeated contact with food and shall function over a temperature range of -60F to 212F. The gasket shall not deteriorate as a result of exposure to repeated cleaning in a mechanical dishwashing

20、environment. The gasket shall be removable from the cover for cleaning. The covers shall have a 1/8 inch diameter raised air vent (open; unsealed) and a recessed lifting handle. 2.1.4 Plastic insert pans type II, and III. The insert pans shall be fabricated of a synthetic thermoplastic polymer. Inse

21、rt pans shall have NSF/ANSI Standard #2 listing, and meet all FDA regulations for articles having repeated contact with food and shall function over a temperature range of -40F to 375F. Third size pans (5 5/8 by 11-5/8 by 6 inches deep inside dimensions), and full size pans (11 1/2 by 19 1/2 by 5 5/

22、8 inches deep) shall have a smooth bead around the top edge for easy cleaning and sealing. All inside corners shall be rounded and the flange (1/4 inch all around pan) shall have a minimum of 1/16- inch flat horizontal termination around the trimmed edge to strengthen the flange on the pan. Pans sha

23、ll be supplied with a plastic cover that has an integrated gasket to prevent liquid leakage. The lid shall meet all FDA regulations for articles having repeated contact with food and shall function over a temperature range of -40F to 210F. The gasket shall not deteriorate as a result of exposure to

24、repeated cleaning in a mechanical dishwashing environment. 2.1.5 Divider bar. The divider bar (1 required) shall be 12-3/4 inches long, color white. The divider bar for the size 1, 2 and 3 containers shall accommodate two tray pack cans (see figure 1). The divider bar shall be of sufficient strength

25、 to maintain the location and support two tray pack cans and function over a temperature range of 33F to 180F 2F. 2.2 Thermal performance. 2.2.1 Hot. When each insert pan (3) in the container is filled with water having a temperature of 180F 2F, the water temperature shall decrease no more than 40F

26、when the container is exposed to an ambient temperature of -20F 5F for 4 hours. Prior to testing, the container shall be preheated by filling only the three insert pans with 180F 5F water, installing the pan covers and container lid, and holding for 10 minutes. Refill insert pans with water having t

27、he specified temperature. Test as specified above. 2.2.2 Co1d. When each insert pan (3) in the container is filled with water having a temperature of 33F +2F, -0F, the water temperature shall increase no more than 12F when the container is exposed to an ambient temperature of l20F 5F for 4 hours. Pr

28、ior to testing, the container shall be pre-chilled by filling only the three pans with a mixture of ice and water, installing the pan covers and container lid, and holding for 10 minutes. Empty all ice. Refill insert pans with water having the specified temperature. Test as specified above. 3 Provid

29、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52193F 2.3 Codes and standards. The insulated food containers shall comply with NSF/ANSI Standard No.2. 2.4 Molded identification marking (“government unique“ requirement see 6.8). When specified (see 6.3

30、), the insulated food container shall be furnished with identification information molded or embossed into the surface of the container body. The information required shall be as follows: “National Stock Number Manufacturers Name Manufacturers Address Manufacturers Model Number _.“ 2.5 Finish The su

31、rface of the finished container shall comply with the finish requirements of NSF/ANSI Standard No.2. 2.6 Workmanship. The insulated food containers shall be complete, clean and free of scratches, dents, breaks, sharp edges and corners, and deformities. All components and assemblies shall be free of

32、dirt and other extraneous materials. Burrs, slivers, rough die, tool, and grinding marks, dents, and cracks shall be unacceptable. Threaded fasteners shall not be missing, broken, cracked, or stripped of threads. There shall be no defects affecting serviceability, durability, operation, performance

33、or appearance. 2.7 Classes (“government unique“ requirement) (see 1.2, 6.3, and 6.8). The body and lids of the sizes of insulated food containers shall be either Brown (class 1) conforming to FED-STD-595, Color Nos. 20313, 30313, or 30279; or Green (class 2) conforming to Fed-STD-595, Color Nos. 240

34、97, 34094, 34095, 34096, or 34097. Food containers of a specific lot shall not exhibit any variation in shade from the specific color selected and specified in the contract for that production lot. 2.8 Metric products. Products manufactured to metric (SI) dimensions will be considered on an equal ba

35、sis with those manufactured using inch-pound units, provided they fall within the tolerances specified using conversion tables contained in the latest revision of IEEE/ASTM SI10, and all other requirements of this Commercial Item Description are met. If a product is manufactured to metric (SI) dimen

36、sions and those dimensions exceed the tolerances specified in inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer may accept or reject the metric product. 3. REGULATORY REQUIREMENTS. 3.1 Recovered materials. The off

37、eror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). Recycled or reclaimed materials may be used in the construction of the equipment described herein. Recycled and reclaimed mater

38、ials shall consist of previously used material, which has been reprocessed to become a source of new raw material. Under no conditions or circumstances shall the contractor submit to the Government for acceptance reconditioned or rebuilt components as a part of the equipment described herein. 4 Prov

39、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52193F 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided shall meet the salient characteristics of this Commercial Item Description, and (except for any government unique

40、 requirements specified), conform to the producers own drawings, specifications, standards and quality practices, and be the same product offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as m

41、ay be otherwise provided for under the provisions of the contract. 4.2 Market acceptability. The following market acceptability criteria are necessary to document the quality of the products to be provided under this Commercial Item Description: a. The company producing the product must have been pr

42、oducing this product, or a similar product, for at least 1 year, to meet the requirements of the CID. b. The company must have sold at least 2000 units of the product, or a similar product, meeting the requirements of this CID in the commercial marketplace over the last 2 years. 4.3 Inspection requi

43、rements. Bid samples may be required for CID items when necessary to assure product quality. In general, first article testing should not be required. First article testing may only be required for those items produced on demand, which are customized. Detailed procedures on inspection requirements o

44、r sampling in a CID should be minimized and used only when no other method for assuring quality is acceptable. 4.4 NSF International standard compliance. Prior to approval of the first shipment, the contractor shall provide satisfactory evidence to the contracting officer (or his authorized represen

45、tative) that the food containers conform to the applicable requirements of NSF/ANSI Standard No.2. Acceptable evidence of meeting the requirements of NSF/ANSI Standard No.2 shall be a listing in the current edition of the NSF International “Listing of Food Service Equipment“ and display of the NSF I

46、nternational mark on the finished product, or a certified test report from a recognized independent laboratory acceptable to medical authority of the Government indicating that the item complies with the applicable NSF International requirement. 4.5 Warranty. Unless otherwise specified in the contra

47、ct, the manufacturers standard commercial warranty shall apply. 5. PACKAGING. 5.1 Packaging. Preservation, packing and marking requirements shall be as specified in the contract or purchase order (see 6.3). 6. NOTES. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

48、nse from IHS-,-,-A-A-52193F 6.1 Intended use. The insulated food containers are intended for use in transporting either hot (160F to 180F) or cold (35F to 40F) foods to remote feeding sites. Ambient temperatures range between -20F to120F. 6.2 Commercial item certification When this CID is used for p

49、rocurement, the commercial item certification clause must appear in the solicitation. 6.3 Acquisition requirements. Acquisition documents must specify the following: a. Title, number and date of this document. b. Size, type, and class of container required (see 1.2, 2.1, and 2.7). c. When molded identification marking is required (see .4). d. Packagin