DLA A-A-52303 A-2011 HOOKS BOAT BALL POINT.pdf

1、 Beneficial comments, recommendations, additions, deletions, etc., and data that may improve this document should be sent to: DLA, Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus, OH 43218-3990, or email to FluidFlowdla.mil. Since contact information can change, you may want to verify the curr

2、ency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 2040 COMMERCIAL ITEM DESCRIPTION HOOKS, BOAT, BALL POINT The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCO

3、PE. This commercial item description (CID) covers the general requirements for wooden handle boat hooks that are intended for applications in the handling of pontoons and other small marine craft. Boat hooks covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/P

4、ART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see figure 1) (see 7.1). 2.1 Classification. Type: A - 96 inches long, 1.5 inches diameter B - 120 inches long, 1.5 inches diameter C - 144 inches long, 2.0 inche

5、s diameter D - 84 inches long, 1.5 inches diameter E - 93 inches long, 1.5 inches diameter (modified, see figure 1) F - 96 inches long, 2.0 inches diameter 2.2 PIN. This example describes a part numbering system for A-A-52303. AA52303 X XXX CID Specification Number Type Length of wooden handle in in

6、ches INCH-POUND A-A-52303A 08 December 2011 SUPERSEDING A-A-52303 8 April 1992 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52303A 2 NOTE: Dimensions are in inches FIGURE 1. Boat hook (ball point). 3. SALIENT CHARACTERISTICS. 3.1 Interface and

7、 physical dimensions. Boat hooks supplied to this CID shall be as specified herein (see figure 1). 3.2 Design. The boat hook shall consist of a cast metal hook riveted to a wooden handle. The boat hook shall be constructed to withstand a longitudinal axis pull of a tensile or dead weight load of 300

8、 pounds applied to the hook. There shall be no evidence of deformation, separation, cracking, loosening, or any other evidence of a failure of the boat hook after verifying the load specified. The configuration of the boat hook assembly, i.e., the length of the hook and the length and diameter of th

9、e handle, shall be as shown in figure 1. 3.3 Materials. The materials and parts shall be selected to accomplish performance requirements and provide maximum safety to operating personnel. 3.4 Metal. All metal parts shall be made of corrosion-resistant materials or shall be suitably protected against

10、 internal or external corrosion during normal service operations and storage. 3.4.1 Dissimilar metals. The use of dissimilar metals in contact with each other shall be avoided. When this is not possible, they shall be suitable protected against each other to minimize or prevent galvanic corrosion. 3

11、.5 Hook. The hook shall be cast malleable iron conforming to ASTM-A47/A47M and zinc coated by one of the following processes: hot dipped, conforming to ASTM-A153/A153M, class B3; electro-deposition process, conforming to ASTM-B633, type II, class FE/ZE 13; or mechanically deposited process, conformi

12、ng to ASTM-B695, type II, class 12. Yellow brass (manganese bronze), designated as a copper alloy in the Unified Numbering System (UNS) as C86100 to C86800, may be used. 3.6 Handle. The handle shall be made from ash wood coated with no less than two coats of spar varnish or suitable polyurethane or

13、epoxy paint. It shall be capable of performing tasks associated with boat handling of small pontoons and small marine crafts. 3.7 Rivets. The rivets shall be of steel and zinc coated, or brass. 3.8 Marking. Boat hooks supplied to this CID shall be marked with the manufacturers (MFRs) standard commer

14、cial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52303A 3 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally pre

15、ferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. Boat hooks shall be processed in such a manner as to be uniform in qual

16、ity and shall be free from other defects that will affect life, serviceability, or appearance. All cast and fabricated components of the boat hooks shall be in accordance with high grade industry practices to assure safety of personnel. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encourage

17、d to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own dr

18、awings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the

19、 quality of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 5 years. b. The company producing the item must have sold at least 25 units meeting this CID in the commercial marketplace ove

20、r the past 2 most recent procurement years. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environment

21、ally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the date of this document, the U.S. Environmental Protection agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list

22、 of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements

23、 specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these boat hooks to DLA Land Use of Recovered Materials; Policy (Copies of this document is available online at www.acquisition.gov/comp/far/index.html or

24、from the U. S. Government Printing Office, 732 North Capital street NW, Washington, DC 20401. Other publications. ASTM INTERNATIONAL ASTM-A47/A47M - Standard Specification for Ferritic Malleable Iron Castings Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

25、HS-,-,-A-A-52303A 4 ASTM-A153/A153M - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware ASTM-B633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel ASTM-B695 - Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Ste

26、el (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) (Industry association specifications and standards are generally available for reference from libraries. They are also dis

27、tributed among technical groups and using Federal agencies.) 7.5 Ordering data. Procurement documents should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements (see 6). 7.6 Commercial products. As part of the market anal

28、ysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial product that would meet the requirements of the CID. (NOTE: This information should not be co

29、nsidered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and address 30396 Century Metal Parts Corp. 230 S. Fehrway Bay Shore, N.Y. 11706-1208 Phone: 631-667-0800 Fax: 631-667-0802 E-mail 7K520 Shaw & Tenney, Inc. P.O. Box

30、 213 20 Water Street Orono, Maine 04473 Phone: 207-866-4867 Toll Free: 800-240-4867 E-mail: 19175 Stefanowicz & Lutz Inc DBA Merit Metal Products Corp. 242 Valley Road Warrington, PA 18976-2520 Phone: 215-343-2500 Fax: 215-343-4839 E-mail 61125 J.G.B. Enterprises Inc. 115 Metropolitan Drive Live

31、rpool, NY 13088-5389 Phone: 315-451-2770 Fax: 315-451-8503 E-mail url: http:/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52303A 5 1UF60 U.S.A. Spares Inc. 1468 Trindle Rd. Carlisle, PA 17015-9741 Phone: 717-241-9222 Fax: 717-241-2977 E-mail

32、: 0M312 Valley Woodcraft and Lumber Co. Inc. 1167 North Washington St. Wiles-Barre, PA 18705-1837 Phone: 570-826-0411 Fax: 570-826-1303 E-mail: 7.7 Part number (P/N) supersession data. These CID PINs supersede the following MFRs P/Ns as shown in table I. This information is provided to assist in r

33、educing proliferation in the Government inventory system. TABLE I. P/N supersession data. Dash number (see 2.1) AA52303- MFRs CAGE 61125 PIN 1/MFRs CAGE 1UF60 PIN 1/MFRs CAGE 0M312 PIN 1/A AA52303-A-96 AA52303-A AA52303-A-96 B AA52303-B-120 AA52303-B AA52303-B-120 C AA52303-C-144 AA52303-C AA52303-C

34、-144 D AA52303-D-84 AA52303-D AA52303-D-84 E AA52303-E-93 AA52303-E AA52303-E-93 F AA52303-F-96 AA52303-F AA52303-F-96 Dash number (see 2.1) AA52303- MFRs CAGE 19175 PIN 1/MFRs CAGE 30396 PIN 1/MFRs CAGE 7K520 PIN 1/A 3306B-A AA52303-A BH-A B 3306B-B AA52303-B BH-B C 3306B-C AA52303-C BH-C D 3306B-D

35、 AA52303-D BH-D E 3306B-E AA52303-E BH-E F 3306B-F AA52303-F BH-F 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For a

36、ctual part marking requirements see 3.8. NOTE: For NSNs listed in table I see table II for cross-reference to manufacturers P/N. 7.8 Government Users. To acquire information on obtaining these ball point boat hooks from the Government inventory system, contact DLA Land and Maritime, ATTN: -FMV, P.O.

37、 Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7741. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52303A 6 7.8.1 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID. The list is for in

38、formation only and may not be indicative of all possible NSNs associated with the CID. For up to date information on assigned NSNs, please contact the aforementioned DLA Land and Maritime office (see 7.8). TABLE II. NSNs CID PIN PIN listed with NSN CAGE NSN AA52303-A-96 AA52303-B-120 H389 21530 2040

39、-00-268-9250 AA52303-C-144 A-52303-C-144 58536 2040-00-256-9047 AA52303-D-84 13216E9929 97403 2040-00-007-1136 AA52303-E-93 1/ 2588578 80064 2040-00-287-5495 AA52303-F-96 A-A-52303 58536 2040-00-255-6071 1/ The overall length includes the hook and pole as an assembly (AA52303-A-96 modified) (see fig

40、ure 1). 7.9 Key words. Brass Handle Iron Malleable Rivets Wooden 7.10 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDATING ACTIVITY Cus

41、todians: GSA - FAS Army AV Navy SH DLA CC Preparing activity: Review activities: DLA CC Navy MC, SA (Project 2040-2011-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-