DLA A-A-55075-1992 GLOVES MEN-S AND WOMEN-S ANTI-CONTACT《男式和女式防接触手套》.pdf

1、A-A-55075 84 m 7999774 0087506 687 m 1 INCH-POUND I A-A-5 507 5 17 Auqust 1992 COMMERCIAL ITEM DESCRIPTION GLOVES: MENS AND WOMENS, ANTI-CONTACT The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-G-10902. Abstract. This Commercial Item

2、 Description covers one type of simplex knitted cotton glove with leather reinforcement palm, fingers, and thumb. The gloves are intended for use by Defense Department personnel in cold-wet and cold-dry regions where dexterity and protection from cold metal contact are required. Classification. The

3、glove shall be provided in one type and three sizes. Salient Characteristics. The matched pair of gloves shall have a knitted cotton body of a Gunn design featuring a leather reinforcement palm patch. The cotton cloth glove parts shall be assembled by inseams, including a Bolton thumb design. A rein

4、forcement leather piece shall be superimposed over the pale side of the sewn cotton glove, covering front side of fingers, palm and thumb and stitched 1/16 to 3/32 inch from the edge of the leather patch. The cloth thumb shall be superimposed with the leather thumb patch, catching the edge of the le

5、ather into the inseam for the closing of the thumb. The remaining edge of the superimposed leather shall be stitched through at 1/16 to 3/32 inch from the leather edge, as indicated by dashed lines on Figure 1 (Front) view. The reinforced thumb shall be set into I Beneficial comments (recommendation

6、s, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Impr

7、ovement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55075 84 99999

8、74 0087507 513 W A-A-5507 5 the glove by inseaming, as indicated by solid lines on Figure 1. The glove back wrist portion shall feature a stretch zone created by an underlying elastic webbing. The grain side of all leather components shall face the outside. The elastic webbing, 2-1/4 to 2-3/4 inches

9、 in length, shall be stretched to its full length, 3 to 3-1/2 inches, and zigzag stitched from one end to the other onto the back wrist area using 1/4 inch stitch width (Figure 1). The zigzag stitching shall contain 15 to 20 points (“V“ shaped units). The tips of the four fingers and thumb on the pa

10、lm side shall be shirred between the joints indicated by notches. The length of the seam edges of the finger and thumb portions, after shirring, shall approximate the length of the seam edges of the corresponding finger and thumb backs. Excepting thumb, all side seams shall be straight and parallel.

11、 Finger tip seams shall be worked to form a moccasin effect. The top of the glove shall be hemmed. All ends of stitching not caught in other seams or covered by other rows of stitching shall be backstitched 1/2 inch. A permanent identification/size label shall be affixed to the inside, palm side of

12、wrist. The finished, matched pair shall be joined together by means of cord thread enabling the pulling apart of the pair, without tearing the gloves. Material. Leather: The leather shall be full grain, soft, flexible deerskin conforming to type VI of KK-L-2004 except that colorfastness to dry crock

13、ing shall be not lower numerically than Munsell value 6.0, and the thickness shall not be less than 1 1/2 ounces, nor more than 2 ounces. The skins shall be split, buffed, shaved, or skived to produce the required thickness with a smooth, clean surface on the flesh side. The color of the leather sha

14、ll be seal brown closely approximating the color of the cloth. Cloth: The cloth shall be a cotton simplex knitted fabric in Seal Brown, shade No. 105. The cloth shall show good colorfastness to laundering, perspiration and crocking. The finished cloth shall conform to the following requirements. Phy

15、sical Requirements Characteristic Requirement Test Method Weight 9.5 Wales, per inch (min.) 60 Courses, per inch (min.) 42 Bursting Strength lbs. (min.) 130 Stretch, percent Wales (length) (max.) 15 ASTM D 3776-85 ASTM D 3887-80 ASTM D 3887-80 ASTM D 3787-89 see Stretch test Provided by IHSNot for R

16、esaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55075 84 W 9999974 0087508 45T W A-A-55075 Physical Requirements (Cont) Characteristic Requirement Test Method Colorfastness Laundering good AATCC 61-1986 Perspiration good AATCC 15-1985 Croaking good AATCC 8-1985 Dimensio

17、nal stability 2% in either direction AATCC 150-1987 Stretch test. (Cloth Only) Preparation of specimens. One specimen each from the length (wales) and width (courses) direction shall be tested from each sample unit. Each specimen shall be rectangular 4 inches by not less than 5 inches. The long dime

18、nsion should be parallel to the length (wales) of the cloth for length tests and parallel to the width (course) for width tests. The test specimens shall be taken no nearer to the selvage than 1/10 the width of the cloth. Two parallel lines 3 inches apart shall be drawn at right angles to the long d

19、imension of the specimen. In addition, a line shall be drawn parallel to the long dimension of the specimen and 1 inch in from either edge for properly aligning the specimen in the jaws of the testing apparatus. Test apparatus. The test device (see Figure 2) shall be an apparatus wherein the specime

20、n is held between the clamps. The design of the upper clamp shall be such that one gripping surface of the jaw shall be an integral part of the rigid frame or clamp. The face of the moveable jaw shall measure 1 inch by 1 1/2 inch or more inches with the long dimension perpendicular to the direction

21、of the application of the load. The lower clamp shall have similar jaws and, when weight is attached, shall weigh a total of 6 pounds. The jaws shall have smooth gripping surfaces, sufficiently flat and parallel to prevent slipping of the specimen during the test. Procedure. The specimen shall be pl

22、aced symmetrically in the clamps of the apparatus with the long dimension parallel and the short dimension at right angles to the direction of the application of the load. Using the specified guidelines, the specimen shall be aligned with one outside edge of the front jaws of each clamp. The proper

23、weight shall be added to insure a total of 6 pounds (including the weight of the lower jaws). The load shall be applied for 15 seconds and the distance between jaws measured by a pair of dividers or other suitable instrument. The elongation at the required load shall be expressed as the percent incr

24、ease in the length of specimen between the jaws. The percent stretch shall be calculated as follows: 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55075 154 = 9999974 0087509 396 A-A-5507 5 Percent = Stretch dimension - Oriqinal 3 inch dimens

25、ion X 100 Stretch Original dimension (3 inches) Report. The results obtained shall be reported separately to the nearest 1.0 percent. Seaming and Stitching: General purpose nylon thread, Seal Brown AM C.A. 66054, twisted, multiple cord; soft or bonded finish; or monocord, bonded finish, 3 ply, 6.0 t

26、.p.i., nominal Tex no. (g/km) 68. The thread shall show fastness to laundering and light equal to or better than the standard sample. When no standard sample is available, the dyed thread shall show good fastness to laundering and light. Shirring: Nylon thread, as per above, or as an alternate, Cott

27、on machine thread, dyed Seal Brown AM C.A. 66054, conforming to type I, ticket No. 30, 3 ply of A-A-52094. The thread shall show fastness to laundering and light equal to or better than the standard sample. When no standard sample is available, the dyed thread shall show “good“ fastness to launderin

28、g and light. Webbing: The unbleached elastic webbing with a 50% stretch shall be 3/8 inch wide, .035-.O5 inch thick, and the weight shall be 20 ounces per linear yard, (min). Label. Identification and size label. Each glove shall be marked with a combination identification and size label containing:

29、 item description, contract number, national stock number, and contractors name. The color of the marking medium shall be white. The label shall be made by either marking, heat transfer (decalcomania), direct printing, stamping or stenciling. The label printing medium shall consist of suitable nonto

30、xic dye(s) or pigment (s). The print shall be well defined, clearly legible and shall not show off-setting, smearing, bleeding, or discoloration. The label shall withstand fastness to laundering as stated therein. Combined wearinq/launderinq instruction label. A printed slip of thin paper containing

31、 the following wearing/laundering instructions shall be inserted in one of the gloves: 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55075 84 9399974 0087530 O08 A-A-5507 5 GLOVES, MENS AND WOMENS, ANTICONTACT WEARING INSTRUCTIONS NEVER HANDL

32、E COLD METAL WITH BARE HANDS-AVOID METAL BURNS USE THESE GLOVES TO AVOID TOUCHING COLD OBJECTS WHEN DELICATE ADJUSTMENTS ARE REQUIRED. DO NOT USE FOR ROUGH WORK. LAUNDERING INSTRUCTIONS TO MAXIMIZE WEAR-LIFE - AVOID UNNECESSARY LAUNDERING HANDWASH SEPARATELY (COLOR MAY BLEED) IN WARM WATER USING MIL

33、D SOAP. RINSE THOROUGHLY, GENTLY RING OUT, SPREAD TO ORIGINAL SHAPE, PLACE FACE DOWN ON PAPER TOWELS, AND AIR DRY ONLY DO NOT USE DETERGENT/CLEANING FLUIDS/SHOE CREAMS BLEACH/SADDLE SOAP Patterns. The government shall furnish a single size pattern. The contractor is responsible for grading patterns

34、for additional sizes. The pattern generally provides for a seam allowance of 1/16 inch for joining seams. Commercial patterns may be used in lieu of the government furnished pattern, provided they conform to the cited design and finished measurements. Cuttina Requirements. All knitted parts shall be

35、 cut from one piece of fabric with the length direction (hem to fingertip direction) of the part running the wale direction. All leathers shall be dampened and stretched out in the length direction (but, to head direction of the hide). Each glove leather component shall be cut with the length direct

36、ion, hem to fingertip, in the length direction, (butt to head direction) of the leather. Sizes and Measurements. The finished glove, after laying-off, shall conform to the measurements below: 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5507

37、5 84 = 9999974 0087511 T44 Size A-A-5 5 07 5 A - Overall length B - Minimum width inches inches Table I Small Medium Large 10 - +1/4 10 1/4 +1/4 10 1/2 i1/4 4 4 1/4 4 1/2 NOTE: Refer to Figure 1 for location of A and B measurements. Workmanship. After completion, the finished gloves shall be thoroug

38、hly cleaned, and all loose thread, lint, and foreign matter removed. The items shall be uniform in quality and shall be free from irregularities or defects which adversely affect appearance, reliability or durability. Finger seam allowances shall not exceed 1/32 inch in width. Gloves shall be dampen

39、ed or humidified and them laid off on laying-off boards heated to not less than 125O F. The seam on the finger tips shall be worked to the back of the boards to form the moccasin effect and the glove shall be pulled down so that the side seams of fingers shall be straight and parallel to the side se

40、am in the glove. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria a

41、nd basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this

42、contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Qualitv Assurance Certification. The contractor shall certify that the product offered meet

43、s the salient characteristics of this description. The producers option to use his own drawings, specifications, standards and quality assurance practices is predicated on full compliance with the salient characteristics. In the event of conflict between producers technical data package and governme

44、nt requirements, the latter shall always take precedence. The government reserves the right to require proof of such conformance prior to the first delivery, and thereafter, as may be otherwise provided for, under the provisions of the contract. 6 Provided by IHSNot for ResaleNo reproduction or netw

45、orking permitted without license from IHS-,-,-A-A-55075 BY Examination. Lots of gloves shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The inspection level

46、for visual examination shall be II and the AQL 10 for total (major and minor combined). The sample unit is one glove and the selection shall be made in pairs. For the pairing examination, the pair shall be examined together and each defect for pairing shall be scored as a single defect . Dimensional

47、 Examination. The finished gloves shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one glove; the inspection level shall be S-3 and the AQL shall be 4.0. Packaqinq Examination. The fully pa

48、ckaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and AQL shall be 2.5. Examination Defect Material Content Missing, damaged, not as required. Number o

49、f gloves per shipping container is more or less than required. Defects. The gloves shall be examined for the following defects: Assembly: any hole, cut, tear, color not uniform or as specified; shaded parts; any spot or stain (outside); dimensions not as specified; malformation, or detail, affecting comfort of wearer resulting from careless sewing; any component not as specified; any open seam; glove not neatly laid off or exhibiting moccasin effect; gloves not