DLA A-A-55105-1992 BAG BARRACKS《棚屋袋》.pdf

1、e A-A-55105 9999974 OL2LO90 872 A-A-5 5 1 O 5 17 December 1992 COMMERCIAL ITEM DESCRIPTION BAG, BARRACKS The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-B-2378. Abstract. This document covers bag, barracks one type and size, with dr

2、awstring closure. a laundry bag to hold the soiled clothing of enlisted men and The barracks bag is intended for use as women. a Salient Characteristics. The bag shall be made of cloth, sateen, cotton, 8.2 oz the color shall be Camouflage Green 483. finished bag shall measure 32 2 3/4 inches in leng

3、th by 24 3/4 2 1/2 inches in width. The construction shall conform to Figure 1, and shall be as specified herein. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. The Beneficial comments (recommendations, a

4、dditions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvem

5、ent Proposal (DD Form 1426) appearing at the end of this document or by letter. i AMSC N/A DISTRIBUTION STATEMENT A. lo FSC 8465 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55105 W 99999

6、74 O121091 709 A-A-55 1 O 5 Materials. Thread, isolvester. soft multiple cord. polyester. Thread Camouflage Green 48 to laundering. The thread for all stitching shall be twisted The yarn shall be continuous multifilament size is 70, the thread shall be dyed 3. The thread shall show good color fastne

7、ss Braid, tubular, cotton. The braid shall be 6/32 inch diameter, solid. The cotton used to make the yarn shall be carded, spun, and twisted into ply yarns. The length of the braid shall be 62 2 1/2 inches, two (2) braid are required for the bag. The braid shall be dyed CG 483 and shall show fastnes

8、s to light, laundering (after 3 cycles), crocking, and wet-dry cleaning. The natural finish shall denote a braid for which no consistency or luster other than that inherent in the basic fiber is required. Grommets. The grommets shall be brass and spur washer, and shall conform to type III, Class 3 s

9、ize No. 1 of MIL-G-16491. Markinq. The identification marking shall be applied in the location shown on Figure 1. The letters “US“ shall be applied in the size characters and in the location indicated on the figure and the markings shall have color fastness to laundering. Workmanship. After completi

10、on, the finished bag shall be thoroughly cleaned, and all loose thread, lint, and foreign matter removed. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Dem

11、onstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve

12、 as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. 2

13、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55105 D 9999974 012LO92 b45 D A-A-5 5 105 Component and assembly Any operation omitted, I added or not performed I Oualitv Assurance Certification. The contractor shall certify that the product that

14、 the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Re

15、liance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. 4 offered meets the salient characteristics of this description and 4 Examination.

16、 Bag Lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The bag shall be examined for the defects listed below. The lot size shall be expressed in units o

17、f bags. The sample unit shall be one bag. The inspection level shall be S-3 and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 1.0. Visual defects Examination Defect Cloth Hole, cut, or tear; any smash, weak place, broken or missing yarn, multiple float

18、s, or open place, clearly visible. Shade bar, fine or coarse filling bar. Examination: Workmanship Not within industry standards or practices. Grommet * Clinched excessively tight, cutting surrounding material. Insecurely clinched to a degree that grommet may be detached from material. 3 Provided by

19、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55105 m 999Y OL21093 5L m A-A-55 1 O 5 Visual defects Examination Defect Hems Drawstrings (two required in hem Markings Cleanness Seam badly pleated or Needle chews. puckered. Formed on outside of bag. Twisted

20、 or pleated. Either drawstring caught in hem stitching causing failure to draw freely. loop not extended thru grommet on each side. Omitted, incorrect, illegible, misplaced or size of characters not as specified. Spots or stains clearly noticeable; thread ends not trimmed to 1/4 inch maximum length.

21、 Dimensional Examination. The finished bag shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one bag; the inspection level shall be 5-3 and the AQL, expressed in terms of defects per hundred

22、 units, shall be 1.0. Defects. The bag shall be examined for the following defects: any hole, cut, tear, color not as specified; any or stain (outside); thread ends not removed; label missing, incorrect, or illegible; measurement of item not as specified. Packauinu Examination. The fully packaged sh

23、ipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be 5-2 and AQL, expressed in terms of defects per hundred units, shall be 1.0. 4 Provided by IHSNot for ResaleNo repr

24、oduction or networking permitted without license from IHS-,-,-A-A-55105 = 9999974 012109q q1 I Overseas. A-A-55 1 O 5 I Packacrinq. Each bag shall be folded. Packacrinq. Fifty bags shall be packed in a fiberboard box conforming to style RSC-L, grade 275 of PPP-B-636. The inside dimensions of the box

25、 shall be approximately 24 by 16 by 13 inches. The box shall be closed in accordance with the appendix Of PPP-B-636. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Materials Workmanship Content Palletization Any comp

26、onent missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items not as specified on shi

27、pping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified PACKING. Palletization. Boxes shall be palletized on a 4 way entry pallet in accordance with load type Ia of MIL-STD-147. Each prepared load shall be bonded with

28、primary and secondary straps in accordance with bonding means C and D, or film bonding means F or G. The pallet pattern shall be number 3 in accordance with the appendix of MIL-STD-147. t Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55105 9999

29、974 OL2b095 354 A-A-5 5 1 O 5 Markinq. Marking shall be in accordance with MIL-STD-129. Domestic. Packacrina, P ackina, p alletization. and markinq. Packaging, palletization, and marking shall be in accordance with ASTM D 3951. Recrulatorv Reauirements. use recovered materials in accordance with Pub

30、lic Law 94-580 to the maximum extent practicable. The offeror/contractor is encouraged to Source of Government Documents. documents are available from: Copies of Military and Federal Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonaovernment

31、 Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies

32、 should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodian: DLA-CT Review Activity: Army- GL Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0129 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-P h o h A-A-55105 = 9999974 0L2L096 290 FIGURE 1 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-