DLA A-A-55140-1993 CONNECTORS ELECTRICAL IEEE 488 COMPATIBLE RECTANGULAR MINIATURE POLARIZED SHELL RECEPTACLE SHIELDED 24 POSITION FLAT CABLE TERMINATING INSULATION DISPLACEMENT SC.pdf

1、A-A-55140 9 9999974 0161bb5 705 A-A-55140 December 7, 1993 COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, IEEE 488 COMPATIBLE, RECTANGULAR, MINIATURE, POLARIZED SHELL, RECEPTACLE, SHIELDED, 24 POSITION, FLAT CABLE TERMINATING, INSULATION DISPLACEMENT, SCREU LOCKING, PREASSEMBLED CONSTRUCTION Th

2、e General Services Administration has authorized the use of this commercial item description (CID). Abstract. receptacle, electrical digital interface bus connector. require conformance to the IEEE 488 interface standard, and require termination of a 1.27 millimeters (.O50 inch) flat cable. and shal

3、l not be used in military systems needing stringent environmental and electrical requirements. Part or Identifyinq Number (PIN). This commercial item description (CID) covers the general requirements for a polarized shell, This connector can be used in applications that Connectors covered by this CI

4、D are intended for commercial/industrial applications The PIN for the CID shall be as shown in the following example: A-A-55140 I o1 - l I i II CID number Dash number Salient characteristics. Desiqn, construction, and dimensions. Design, construction, and dimensions figure 1 and in accordance with I

5、EEE 488. Contacts. The contacts shall be formed of a high conductive, high strength nickel plating in the contact area. Connector housinqs. Connector housings shall be molded from self-extinguishing black thermoplastic material for high impact and dielectric strength. a shall be as specified on copp

6、er alloy with gold over Connector shields. Connector hardware. Termination wire ranqe. Connector shields shall be made of die cast zinc with nickel plating. Connector hardware shall be made of zinc plated carbon steel. Terminations shall be insulation displacement type which accommodate 1.27 millime

7、ters (.O50 inch) centerline flat cable conductor with wire ranges of 26-30 AUG solid or 28 AWG stranded wire. Contact rating. Termination resistance. The contact resistance shall be 22 milliohms maximum initial for mated connectors Contacts shall be rated at 1 ampere maximum at +2SC. and 12 mi llioh

8、ms initial for unmated connectors. Dielectric withstandinq voltage. There shall be no breakdown of the insulating material when subjected to 1000 V ac for 1 minute between adjacent contacts of the mated connector assemblies. Matinq force. Unmatinq force. Durability. Durability shall consist of 200 c

9、ycles of mating and unmoting and upon completion the Connector mating force shall not exceed 3.12 newtons (0.7 pound) maximum per contact. Connector unmating force shall not exceed 0.89 newton (0.20 pound) minimum per contact. ? termination resistance shall not exceed a change greater than 10 millio

10、hms maximum from the initial * resistance. There shall be no indication of physical damage. 4 Operating temperature. The operating temperature range shall be from -4OOC to +75OC. FSC 5935 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleN

11、o reproduction or networking permitted without license from IHS-,-,-A-A-55140 A-A-55140 9999974 OLblbbb 641 I I I I mm 0.013 0.36 2.16 11.94 16.00 36.20 46.79 60.45 INCH .O005 .O85 ,470 .630 1.425 1.842 2.380 . O24 NOTES: 1. Dimensions are in millimeters. 2. The US government preferred system of mea

12、surement is the metric SI system. was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. However, since this item I Figure 1. Connector, receptacle, 24 position, flat cable, locking.

13、 L Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55140 9999974 OLbLbb7 588 A-A-55140 Vibration. The connector, or hardware when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening of parts when subjected to

14、 vibration of 10-55-10 Hz traversed in 1 minute at 1.52 millimeters (.O60 inch) total excursion for 2 hours in each of three mutually perpendicular planes. 9 I I Physical shock. The connector or hardware when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening o

15、f parts when subjected to 50 Gs half-sine wave shock of 11 milliseconds duration, 3 shocks in each direction applied along the three mutually perpendicular planes for a total of 18 shocks. Requlatory requirements. This section is not applicable to this CID. Quality assurance provisions. Responsibili

16、ty for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection, examination, and test requirements specified herein. his own or any other facilities suitable for the inspection requirements specified herein, unless

17、 disapproved by the Government. examinations, or tests set forth in this description where such inspections, examinations, and tests are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otheruise specified in the contract or purchase order, the contracto

18、r may use The Government reserves the right to perform any of the inspections, Contractor certification statement. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of this CID, and that the product conforms to the producers own draw

19、ings, specifications, standards, quality assurances practices, and is the same as the product provided as a bid sample. the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The Government reserves the right to require proof of such conformance prio

20、r to Certificate of compliance. A certificate of compliance shall accompany all connectors supplied to this CID. Packaqing. e Preservation, packaainq, packinq, Labeling, and marking. Preservation, packaging, labeling, and marking shall be as specified in the contract or purchase order. - Notes. proc

21、ess of acquiring the item, but is not mandatory. This section contains relevant information which is useful to buyers, users, and suppliers in the Referenced document. Other Publication INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE) IEEE 488 - IEEE Standard Digital Interface for Programmab

22、le Instrumentation. (Applications for copies should be addressed to the Institute of Electrical and Electronics Engineers (IEEE), IEEE Service Center, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855-1331.) Orderinq data. Acquisition documents should specify the following: a. CID document number a

23、nd revision and CID PIN. t b. Quality assurance provisions. c. Packaging requirements. Comments. Comments on this CID should be directed to Defense Electronics Supply Center, 1507 Wilmington Pike, ATTN: DESC-EMT, Dayton, OH 45444-5M30, or telephone (513) 296-5391. 3 Provided by IHSNot for ResaleNo r

24、eproduction or networking permitted without license from IHS-,-,-A-A-55140 9999974 0161bb8 414 A-A-55140 Source of supply. they become available. A suggested source of supply is listed in table I. Additional sources will be added as t TABLE I. Suggested source of supply. CID PIN A-A-551 40- number 5

25、54434-1 Vendor CAGE number 00779 Vendor name and address AMP, Incorporated 470 Friendship Road Harrisburg, PA 1711 1-1203 I CIVIL AGENCY CORDINATING ACTIVITY: GSA - 7FXE PREPARING ACTIVITY: DLA-ES (Project 5935-D426) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-