DLA A-A-55173-1993 BELT MILITARY POLICE 1-3 4 INCH WIDE MAN-S《男式1-3 4英寸宽军警用皮带》.pdf

1、A-A-55373 9999974 0327738 bL0 = c 4 I INCH-POUND I A-A-5 5 17 3 08 Februarv 1993 COMMERCIAL ITEM DESCRIPTION BELT, MILITARY POLICE, 1-3/4 INCH WIDE, MANS The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-B-1718. Abstract. This documen

2、t covers one type of leather waist belt and is designed for use by Military Police. Classification. The belt sizes and lengths shall be as specified on page 2. Salient Characteristics. The waist belt shall be comprised of three piece leather construction: main body, keeper and loop. The main body sh

3、all be 1-3/4 inch wide. The keeper shall be 3/4 inch wide and 5-1/4 inch in length. The loop shall be 7/16 inch wide and 4-3/4 inch in length. be rounded with a size no. 1 edger. with a center bar buckle. Edges of the belt shall The belt is not furnished Material. Leather. The leather shall be top g

4、rain cattlehide, midew resistant treated type and shall be dyed black and finished smoothly on the grain side. The thickness shall be as follows; main body 8 ounce, keeper 4 ounce, loop 6 ounce. The thickness tolerances shall be plus 1 ounce and minus 1/2 ounce. The leather shall be black in color,

5、insuring a long-lasting smooth finish. facings. color of the belt. The finished grain side will be used for all visible The edges of the belt shall be dye treated to match the Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this doc

6、ument should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street,Philadelphia, PA 19101-8419, by using the self-addressed Standardization Document Improvement Proposal (.DD Form 1426) appearing at the end of this document or b

7、y letter. . AMSC . N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; . distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-553173 W 7Y 0327739 557 M A-A-5 5 17 3 Fastener, SnaD. The snap fasteners shall co

8、nform to a small wire spring clamp type, with a black finish. The snap fastener shall consist of the following components: button, socket, stud and eyelet. The button shall be 1/2 inch in diameter, and all other components shall interface with the button. A total of three snap fasteners are required

9、. Sizes and Lenaths. sizes and overall lengths: (Length tolerance, f 1/8 inch) The belt shall be provided in the following Length 34 42 - Label/Markinq. The letters WSv; and the belt size shall be indented or legibly stamped with black or red indelible marking ink, in 3/16 inch high characters. The

10、manufacturers name, year manufactured and contract number shall be in 3/32 inch high characters. All markings shall appear on the flesh side. . Workmanshb. After completion, the finished belt shall be thoroughly cleaned, and all foreign matter removed. Leather components shall be free from any cut,

11、damaged grain, scratch, hole, brand, hip mark and loose spongy leather. The items shall be uniform in quality and shall be free from irregularities or defects which adversely affect appearance, reliability or durability. Product Demonstration Model. When required, offerers shall submit samples of th

12、eir intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retai

13、ned by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the success

14、ful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Quality Assurance Certification. offered meets the salient characteristics of this description and that the prbduct conforms to the producers own drawings, specifications, standards and q

15、uality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. The contractor shall certify that the product 2 Provided by IHSNot for ResaleNo reprod

16、uction or networking permitted without license from IHS-,-,-A-A-55173 = 9999974 0127720 279 A-A-5 5 17 3 Reliance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requi

17、rements of the contract. Examination. Belt lots shall be inspected in accordance with llSampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The belt shall be examined for the defects listed below. Th

18、e lot size shall be expressed in units of belts. The sample unit is one belt. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 2.0. Defects. The belt shall be examined for the following defects: color or finish not as

19、specified, color not uniform, grain side not smooth finished, tacky or cracked finish. Leather; any hole, cut, tear, wrinkle, color not as specified; any spot or stain (grain side or flesh side) marking missing, incorrect, or illegible; measurement of item not as specified, fastener not functioning

20、properly (i.e., fails to snap closed to provide a secure closure or to open freely), failure to interface with a center bar buckle. Dimensional Examination. The finished belt shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as

21、a defect. The sample unit shall be one belt; the inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 1.5. Packaaing Examination. shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the

22、inspection lot. The inspection level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 1.0. The fully packaged shipping containers EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Material

23、s L Workmanship Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

24、om IHS-,-,-Content A-A-55173 rn 9999974 0127721 105 rn Palletization A-A- 5 5 17 3 Number of items in container is more or less than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as speci

25、fied Load not bonded as specified Resulatorv Reauirements. use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. The offeror/contractor is encouraged to Preservation, Packins. and Markinq. The preservation, packing, and marking shall be as specified in the c

26、ontract or order. Source of Government Documents. documents are available from: Copies of Military and Federal Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Non-Government Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspect

27、ion By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018-3308.) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916

28、Race Street, Philadelphia, PA 19103.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Custodians: , Air Force-99 Review Activity: Air Force-45 Air Force-82 Amy-GL User Activity: Navy-MC A-A-55173 74 0127722 041 = A-A-55173 Civil Agency Coordinating Activity: GSA-FSS Preparing Activity: DLA-CT Project No. 8465-0113 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-