DLA A-A-55181-1993 HOLDER BADGE PLASTIC SECURITY POLICE《安全警察塑料徽章夹》.pdf

1、A-A-55 3 8 3 9999974 0344558 5bT m. +- + ;INCH-POUND: +- t A-A-55181 25 MAY 1993 COMMERCIAL ITEM DESCRIPTION HOLDER, BADGE, PLASTIC, SECURITY POLICE The General Services Administration has authorized the use of this commercial item description in preference to MIL-H-87106. Abstract. This Commercial

2、Item Description covers one type and size if badge used to retain the badge of security police of the Department of the Air Force. Salient Characteristic:. The holders dimensions shall be (3-3/4 inches long x 3/4 inch wide x 0.037 +/-0.004 inch thick). Figure l.“Holder“. Figure 1 IS furnished for in

3、formational purpoxe:, only to the extent of any inconsistencie: between the written (CIG) and the Figure, the written (CID) shall gobern. Material. The transparent holder shall be made from plastic vinyl copolymer material. The material shall be 0.037 thick (+/-0/004). The tearing resistance (origin

4、al property), weakest direction, shall be a minimum of 500 pounds per inch of thickness. The tearing resistance (after oven aging for 7 days at 158 degrees Fahrenheit), decrease from original value, shall be a maximum of 10 percent. Beneficial comments (recommendations, additions, deletions) and any

5、 pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using Standardization Document Improvement Proposal (DD Form 1426) appe

6、aring at the end of this document or by letter. RMSC N/A FSC 8455 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55LBL m 9999974 0144559 4Tb m A-A-55181 O Workman

7、ship. The holder shall be clean and free from dirt, oil, or any oth.er foreign matter; rough or sharp edges; scratches; scuffs; cracks; creases; blisters; bubbles; pimples; undispersed resin; pits; tears; cuts; or holes. Product Demonstration Model. When required, offrer shall submit samples of thei

8、r intended production. The Product Demonstration Model consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by

9、the government. Cce (:) Product Demonstration Motel approved by DPSC Lr,der the re:dltnt contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful off

10、erer of his responsibility to perform in accordance with the Commercial Item Description specified above. Quality Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own dr

11、awings, specifications, standards and quality assurance practices. lhe government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Examination. The Holders shall be inspected in

12、accordance with “Sampling Procedures and Tables for Inspection by Attribute:“, ANSI/ASQC 21.4, pub1i:hed tiy the American Society for Quality Control. Visual Examination. The inspection level for visual examination shall be I and the “Acceptable Quality Level (AQL)“ shall be 1.0. The sample unit is

13、one holder. Dimensional Examination. The finished holder shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one holder; the inspection level shall be 5-3 and the AQL shall be 2.5 Defects. The

14、 holder shall be examined for the following defects: not made of the specified material; color not transparent; any cracks; blisters. Scratche:, cuts, tear, cuts, tears cracks, wrinkles or scuffs; rough edges; surfaces containing voids, pockets or any noticeable defects; holder not clean; measuremen

15、t of item not as specified. O 2. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55181 9 9999974 01445b0 11B A-A-55:81 Preservation, Packing, and Marking The preservation, packing and marking shall be a; specified in the contract or order. O So

16、urce of Government Documents. Copies of Military and Federa; document: are available from: Standardization Document: Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nongovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Ap

17、plications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NI 10018-3308.) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadel

18、phia, FA 19103.) Custodian: Air force 1: Review Activity: Air Force - 45 Air Force - 82 Civil Agency Loordinating Activity: GSA-FS: Preparing Activity: DLA - CT ProJect 8455-0672 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. 3 A-A-55181 999977

19、4 01445b1 054 s A-A-55181 L 5/16 314 x 1 /4 SLOT 911 6 A- t ,? I 2 L 3/16 I -3hL )c SA3 R (TYP) HOLE I - 114- DIAMETER HOLE - 113 - : DXWNSIONS IN INCHES TIIICKNESS : O. 03 7 50.004 iJLE SS OTI IE RUT S F SPECIFIED TOLERANCE: 1/.64 O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-