DLA A-A-55208-1993 TAPE TEXTILE NYLON MULTIPLE TUBULAR《尼龙多管纺织带》.pdf

1、A-A-55208 = 74 0345239 Tb4 I INCH-POUND I A-A- 5 5 2 O 8 May 19, 1993 COMMERCIAL ITEM DESCRIPTION TAPE, TEXTILE: NYLON, MULTIPLE TUBULAR The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-T-5666. Abstract. manufacturing of parachute pa

2、cks. used to pull the pack flaps when the parachute ripcord is pulled. The tape shall be one type of nylon tape for the The tape holds the springs Salient Characteristics. The tape shall be 1 3/8 inches wide (- + 1/16) and manufactured with 210 denier warp and a 420 denier filling. The yarn shall be

3、 bright, high tenacity, light and heat resistant nylon having a minimum of 2-1/2 turns per inch. Material. It is encouraged that recycled material be used when practical as long as it meets the requirements of this document. * Beneficial comments (recommendations, additions, deletions) and any perti

4、nent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appear

5、ing at the end of this document or by letter. AMSC N/A FSC 8315 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55206 9999974 0345220 766 = A-A-55 2 O 8 Weave. back

6、) and one filling. The face and back warps shall weave plain, with one filling yarn per shed. The filling shall accomplish a cross-over; first on the face, then on the back at each 40-warp end interval so that five separated tubular sections shall be formed in the total width. The tape shall be comp

7、osed of two ground warp (face and I Color. Camouflage Green 483, or other color as specified by the procuring activity. The tape shall be yarn or piece dyed to Sage Green 1545, Colorfastness. equal to or better than the rating of 3 on the international grey scale when tested in accordance with AATCC

8、 61-1986 (water temperature 100F 2 4O). The dyed tape shall show fastness to laundering Physical requirements. The dyed tape shall conform to the requirements specified in Table I. Table I. Phvsical requirements Characteristic Requirement Test Method Colorfastness to Laundering . 3 rating AATCC 61-1

9、986 L/ Weave Plain Visual Width 1-3/8 2 1/16 Visual Thickness Weight (max) 0.020 to 0.025 ASTM-D 1777-64 inch 0.40 ounces ASTM-D 3776-85 per linear yd Breaking Strength (min) 500 pounds ASTM-D 5034-90 2/ (original) Elongation (min) 20 percent ASTM-D 5034-90 Total ends (min) 199 Visual Picks per inch

10、 (min) 84 Visual - i/ - 2/ The long dimension of the jaws shall be no less than the width of the specimen. Water temperature shall be 100F 2 4OF. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55208 W 9999974 OL4522L bL2 A-A-55 2 O 8 0 Lencrth

11、 and Dut-up. Unless otherwise specified, the tape shall be put up in rolls of not less than 95 yards and not greater than 105 yards. No roll shall contain more than three pieces and no piece shall be less than 10 yards in length. Workmanship. The end item shall conform to the quality of product esta

12、blished by this document and the occurrence of defects shall not exceed the applicable acceptable quality levels. gualitv Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producer

13、s own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Reliance on contractor quality assurance

14、 systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination Visual Examination. The tape shall be examined for the defects listed below. The lot size sha

15、ll be expressed in units of yards. The sample unit is one linear yard. * Defects. The tape shall be examined for the following defects: any hole, cut, tear, or color not as specified; any spot or stain (outside); thread ends not removed; label missing, incorrect, or illegible; measurement of item no

16、t as specified; bar-code omitted or not readable by scanner, Human-Readable Interpretation (HRI) omitted or illegible; bar-coded type not as specified, code density not as specified. Dimensional Examination. The finished tape shall conform to the dimensions specified. Any dimension that is not withi

17、n the established tolerance shall be classified as a defect. The sample unit shall be one roll. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55208 = 4 0345222 559 A-A-55 2 O 8 Packaqina Examination. The fully packaged shipping containers sha

18、ll be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Ma terials Workmanship Content Pal

19、letization Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items is n

20、ot as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Reuulatorv Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum

21、 extent practicable. Packaqinu, Packinq, Markins, and Palletization The preservation, packing, marking and palletization shall be as specified in the contract or order. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55208 m 9999974 0345223 495

22、 m A-A-5 5 20 8 Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonaovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection

23、 By Attributes - (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916

24、 Race Street, Philadelphia, PA 19103.) Custodian: Army - GL Navy - AS Air Force - 99 Review Activity: Air Force - 82 DLA - CT User Activity: Army - AV Navy - OS Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No.8315-0370 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-