DLA A-A-55211-1993 YARN WOOL《羊毛纱》.pdf

1、A-A-552LL 9999974 0344723 O02 I INCH-POUND 1 A-A-55 2 11 4 June 1993 COMMERCIAL ITEM DESCRIPTION YARN, WOOL The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-Y-16654. Abstract This Commercial Item Description covers worsted yarn inten

2、ded for use in hand weaving, textile work in occupational therapy, and lubricating purposes. Classification. The yarn shall be of the following types: Type I - White or dyed Type II - Natural Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in im

3、proving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or

4、by letter. 4 AMSC N/A FSC 8310 DISTRIBUTION STATEMENT A. Approved for public release; O distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55233 H 9999974 0344724 T49 H A-A-5 5 2 11 Salient Characteristics. The wool top sh

5、all be fleece wool, pulled wool, or any combination thereof not lower in grade than 56s U.S.Standard. The use of noils or laps is prohibited. The finished yarn shall contain not less than 95 percent wool based on the dry weight of the desized specimen. The yarn shall be spun on the worsted system fr

6、om combed top on either the Bradford, French, or American system. The yarn shall be not finer than 8s 4 ply or coarser than 7s 4 ply. The twist shall be soft with 5 turns per inch (25 percent) in the single yarn and 2 turns per inch (25 percent) in the ply yarn. The color of the Type I yarn shall ma

7、tch the standard sample under natural (north sky) daylight or artificial daylight having a color temperature of 7500 Kelvin and shall be a good approximation of the standard sample under incandescent lamplight at 2800 Kelvin. When white is specified, the yarn shall be bleached using hydrogen peroxid

8、e. Unless otherwise specified, the white yarn shall not be treated with an optical bleach. The Type II yarn shall be in the natural condition, undyed, unbleached and not subjected to any chemical processes. Turns per inch singles PlY 5 2 i Hydrogen Peroxide bleach Optical bleach FED-STD 191-5660 a C

9、olorfastness to light (Type I only) good AATCC 16A 5 A laundering good AATCC 61 Test 1A a A Wool content at least 95 percent FED STD 191-2101 . - i A certificate of compliance shall be submitted and will be acceptable for the stated requirement. 2 In the event that the use of an optical bleach is sp

10、ecified or permitted, the optical bleach shall be so selected that the finished yarn shall show no discoloration from light after exposure for 20 standard fading hours followed by 48 hours in the dark. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

11、,-A-A-55211 9999974 0344725 985 A-A-55 2 11 3 The dyed and finished yarn shall show fastness to laundering and to light equal to or better than the standard sample. When no standard sample has been established or designated “good“ fastness to laundering and to light. Use 2 to 6 grams of the applicab

12、le material held together to form a unit for testing unless otherwise specified in the procurement document. The laundering cycle of the launderometer or similar machine shall be 30 minutes and the temperature of the container and its contents shall be maintained at looo t4O F. (. as applicable to c

13、olorfastness, the finished yarn shall show 4 - Label/markinq. Yarn manufactured under this Commercial Item Description shall be labeled in accordance with the Wool Products Labeling Act of 1939. Workmanship. The finished yarn shall conform to the quality and grade of product established by this Comm

14、ercial Item Description. The occurrence of defects shall not exceed the applicable acceptable quality levels. After completion, the finished yarn shall be thoroughly cleaned, and all loose fiber, lint, and foreign matter removed. Reaulatorv Requirements. use recovered materials in accordance with Pu

15、blic Law 94-580 to the maximum extent practicable. The offerer/contractor is encouraged to gualitv Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own specifications, s

16、tandards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall not relieve the contractor of th

17、e responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55211 W 9999974 0144726 811 = A-A-5 5 2 11 Put-u

18、p. Unless otherwise specified, the yarn for Types I and II shall be put-up in 4.0 ounce skeins (210 percent). The average weight per skein, on a lot basis, shall be not less than 4.0 ounces. A lot shall be unacceptable if the average weight is less than the specified weight. The tolerance of plus or

19、 minus 10 * percent allowed per individual skein shall not apply to the average weight. A defect with regard to weight shall be considered to exist if the net weight of any one skein is not 1 within the specified range. The inspection level shall be S-3. The Acceptable Quality Level (AQL) shall be 2

20、.7 defects per 100 units. For lots consisting of 500 or fewer units, the sample size shall be 10 and the acceptance number 1. The lot size shall be the number of units in the inspection lot. Examination. Yarn skeins shall be inspected in accordance with “Sampling Procedures and Tables for Inspection

21、 by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. In-process inspection. Inspections shall be made at any point or during any phase of the manufacturing process to assure that no noils or laps are used and that the dyeing requirements have been adhered to. The G

22、overnment reserves the right to exclude from consideration for acceptance any material for which in-process inspection has indicated non-conformance. Visual Examination. Defects found during this examination shall be classified in accordance with the defects listed in Table II and regardless of thei

23、r proximity to each other, except where two or more defects represent a single local condition, in which case only the most serious defect shall be counted. The sample unit shall be one skein. The Acceptable Quality Level (AQL) shall be 1.5 major defects and 6.5 total (major and minor combined) defe

24、cts per 100 units. The sample size shall be in accordance with inspection level S-l. The lot size shall be expressed in units of one skein. Put-up other than specified X Improperly or not uniformly wound resulting in entangling during unwinding or otherwise affecting free unhampered unwinding of the

25、 skein. X 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55211 74 01YY727 758 A-A-55 2 11 Color e Cleanliness P Other than specified Off shade, i.e. not within established tolerance Spot or stain r Lumps r X X X X Objectionable odor X Identifi

26、cation Not labeled in accordance with (fiber ) Wool Products Labeling Act of 1939 X - i Clearly visible at normal inspection distance (3 feet) Wool. The wool shall be visually examined for grade in top form by comparison with the U.S.Standard Methods of Test for Grades of Wool Top. In the event of a

27、 dispute, the wool grade shall be determined by the width method (wedge). The sample unit shall be one yard of top. The sample size shall be as shown in Table III. The lot size shall be expressed in units of one pound. The result from each sample unit shall be reported separately. The lot shall be u

28、nacceptable if a single sample unit fails to meet the required grade. e Table III Tests. The methods of testing specified, wherever applicable, and as listed in Table I shall be followed. The physical and chemical values specified apply to the results of the determinations made on a sample unit for

29、test purposes as specified in the applicable test methods. The sample unit shall be two skeins. The lot shall be unacceptable if one or more sample units fail to meet any test requirement specified. The lot size shall be expressed in units of one skein. All test reports shall contain the individual

30、values utilized in expressing the final result. The sample size (number of sample units) shall be in accordance with the following: Lot size (skeins) # 800 or less Sample size 2 3 5 801 up to and including 22,000 22,001 and over 5 Provided by IHSNot for ResaleNo reproduction or networking permitted

31、without license from IHS-,-,-A-A-55233 9999974 0344728 694 A-A-55 2 11 Packacrincr Examination. An examination shall be made to determine that the packaging, packing, and marking complies with all listed requirements. Defects shall be scored in accordance with the list below. The sample unit shall b

32、e one shipping container fully prepared for delivery with the exception that it need not be closed. Defects of closure listed below shall be examined on shipping containers fully prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot. The inspec

33、tion level shall be S-2 and the Acceptable Quality Level shall be 1.5 defects per 100 units in accordance with ANSI/ASQC 21.4. Examine Defect Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application. Materials Workmanship Content Preservatio

34、n Any component missing, damaged, or not as specified. Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, inadequate stapling or improper taping. Bulged or distorted container. Open and non-continuous heat sealed seams and closure of polyethylene b

35、ag. Omission of vent hole in polyethylene bag. Incorrectly fabricated bag. Number of skeins per package is more or less than required. Preservation improper, improperly applied or missing. I - i For this defect one package shall be examined from each shipping container in the sample. Preservation, P

36、ackinu, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55211 9999974 0344729 520 A-A-55 2 11 Source of Government Documents. Copies of Military

37、 and Federal documents are available from: , I Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 ? Methods of Test for Grades of Wool Top (Applications for copies should be addressed to the United States Department of Agriculture, Agriculture Marketing Serv

38、ice, Washington, D.C. 20402.) Rules and Regulations Under the Wool Products Labeling Act of 1939 (Applications for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D.C. 20402.) Sources of Nonaovernment Documents. ANSI/ASQC 21.4 - Sampling Procedu

39、res and Tables For Inspection 0 By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) AATCC tests (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O.BOX 12215, Triangle Park, NC 27709-2215.) Custodians: Army - GL Navy - NU Review Activity: Army - MD Preparing Activity: DLA - CT Project No. 8310-0195 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-