DLA A-A-55212-1993 BELT ALL-WEATHER COAT WOMEN-S《女式羊毛带》.pdf

1、A-A-55212 = 9999974 0144574 702 m Class 1 - Marine Corps pewter 2246 Class 2 - Army black 385 I INCH-POUND I A-A-55 2 12 June 14, 1993 COMMERCIAL IT3M DESCRIPTION BELT, ALL-WEATHER COAT, WOMENS The General Services Administration has authorized the use of this Commercial Item Description in preferen

2、ce to MIL-B-29408. Abstract. This document covers the requirements for belts for polyester/cotton poplin womens all-weather coats. The belt is worn by female personnel of the US Marine Corps and the US Army. Schedule of sizes. The belts shall be in the following classes and sizes which correspond to

3、 sizes of coats with which the belts are worn. Classes Sizes Sizes 4, 6, 8, 10, 12, 14, 16, 18, 20, 22 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing

4、and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philsdelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. i AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release; dis

5、tribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55212 W 9999974 0144575 649 A-A-55 2 12 Salient Characteristics. DescriDtion. The belt shall be US Marine Corps design shown on Figure 1, having one end pointed on a 45-degre

6、e angle, and the other end square to attach to the buckle with a keeper, and a belt fastener on the under side to secure belt to coat. Figure 1 shows general design of the belt and is furnished for information only. In the event of conflict between the figure and the text of this document, the text

7、of this document shall govern. The buckle size shall be 2-1/4 inches. The finished strips for the belt keeper and fastener shall be uniform in width, 1/2 2 1/16 inch wide, and topstitched 1/16 inch from each edge. The belt keeper shall be positioned on the belt 6 inches from the unfinished end, and

8、tacked or bartacked to the under side of the belt on each side of the keeper. The keeper shall finish 2-1/2 2 1/8 inches. The belt fastener shall be cut to 9-1/2 inches in length, folded under one end of the fastener 1-1/2 inches, and stitched together 1/16 to 1/8 inch on both sides and across folde

9、d edge. The belt fastener shall finish on the underside of the belt. The interlining shall be positioned to the inside of the belt. The buttonhole shall be a horizontal straight type, 5/8 inch in length, and securely tacked at each end. The gage for stitching shall be uniform in width. The belt shal

10、l be edgestitched on both sides and the pointed end with a double row of stitching 1/16 inch and a 1/4 inch gage from the seamed and folded edge. The belt shall be 2-1/8 2 1/8 inches wide, and shall be pressed smooth and flat with a heated pressing iron or pressing machine. NOTE: A Sonic Macnine may

11、 be used to cut the strips to the proper length. Materials. Basic Fabric. The basic fabric for the belt shall be polyester/cotton blend poplin conforming to A-A-50531. of the cloth shall be Marine Corps pewter shade 2246 or Army black shade 385. The color Interlininq. fusible cloth of 85% polyester,

12、 15% polyamide or 100% polyester, 1.75 to 2.0 ounces per square yard, polyamide paste dot. The color shall be charcoal for class 1 and charcoal or black for class 2. For optimum results, the fusible material manufacturers recommendations fcr fusing dwell cime, Fressure, and temperature, based upon t

13、he fusing equipment used and hasic material being fused, shall be utilized. The interlining for the belt shall be a nonwoven 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55212 m 9999974 OL4457b 585 m A-A-55 21 2 Buckles. The plastic buckle f

14、or the belt shall be a 2-1/4 inch color shall be green AF Cable No. 62017 for class 1 and black shade CT62001 for Class 2. Buttons. The button shall be line 24 4-hole buttons melamine formaldehyde composition. The buttons shall have a glossy finish and shall be green shade AF Cable No. 62017 for cla

15、ss 1 and black shade CT62001 for class 2. general purpose buckle conforming to Class 3 of MIL-B-1860. The * Thread. The polyester/cotton covered thread shall be dyed shade taupe A, Cable No. 66030 for class 1 and shade black AA Cable No. 66043 for class 2 and shall conform to type I of A-A-50199. Th

16、e thread for bartacking, seaming, stitching and buttonholes shall be ticket no. 50, 2 ply, or ticket No. 70, 2 ply. The thread for button sewing shall be ticket No. 30, 2 or 3 ply. The dyed thread shall show fastness to wet-dry cleaning and light equal to or better than the standard sample when test

17、ed as specified in A-A-50199. When no standard sample is available, the dyed thread shall show “good“ fastness to wet-dry cleaning and light when tested as specified in A-A-50199. Label. Each belt shall have a non-woven, commercial type label containing identification, instruction and size informati

18、on. The label shall be acrylic coated, mildew-resistant, and the printing shall show good fastness to dry cleaning. The label shall be printed on-the underside of the belt at the center back. As an alternate, a commercially acceptable hang tag, containing the specified information printed directly o

19、n the tag, may be used. The tag may be attached with string at the buttonhole or with plastic barb holder near neck of belt. The inscription shall read as follows: 0 - Item Description Contract Number National Stock Number Fur, Wool or Fiber Products Act information as applicable Label/taq. Each bel

20、t shall be individually coded with a type VIII, class 17 of DDD-L-20 label/tag bar code for personal clothing items. The label/tag bar code shall be located so that it is completely visible on the garment. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

21、S-,-,-A-A-55212 W 9999974 0344577 411 A-A-55212 Sizes and Measurements. The finished belt shall conform to the measurements below. Measurements in Inches Sizes - Belt Length 4 6 8 10 12 14 16 18 20 22 38 39-1/2 41 42-1/2 44 45-1/2 47 49 51 53 Tolerance - + 3/4 The belt length shall be measured along

22、 the center from the folded edge of the belt at the buckle to the end of the belt. WorkmanshiD. The finished belts shall conform to the quality of product established by this document. The occurrence of defects shall not exceed the applicable acceptable quality levels. Product Demonstration Model. W

23、hen required, offerers shall submit samples of their intended production. The product demonstration model will consist of units independently developed. Product demonstration models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicit

24、ation. Product demonstration models will be retained by the government. One (1) product demonstration model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the product

25、 demonstration model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Requlatorv Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maxim

26、um extent practicable. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55212 W 9999974 0144578 358 A-A-53 2 12 Qualitv Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this desc

27、ription and that the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of

28、the contract. Reliance on contractor quality assurance systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination. Belt lots shall be inspected in accord

29、ance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The belt shall be exsmined for the defects listed below. The lot size shall be expressed in units of belts. The sample unit is one belt.

30、 The inspection level shall be II and the AQL, expressed in terms of defects par hundred units, shall be 1.0. Defects. The belt shall be examinsd for the following defects: any hole, cut, tear, color not as specified; any spot or stain (outside); any pleats, puckering, or raw edges; thread ends not

31、removed; any fusing delaminated, bubbling of any fused component, any strike through or bleed through, or any resin transfer to belt; label missing, incorrect, or illegible; bar code label/tag omitted or not scannable, human-readable interpretation (HRI) omitted or illegible; measurement of item not

32、 as specified. Dimensional Examination. The finished belt shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one belt; the inspection level shall be S-3 and the AQL, expressed in terms of def

33、ects per hundred units, shall be 2.5. Packacrina Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-1 and AQL, expressed in terms

34、 of defects per hundred units, shall be 2.5. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55212 = 9999974 0144579 294 A-A-55 2 12 EXAMINE DEFECT Marking rcitted; incorrect; illegible; (exterior and interior) of improper size, location, or me

35、thod of application Materials Workmanship Content Palletization Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is more or l

36、ess than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Preservation, Packinu, and Markinq. The preservation, packing, and marking shall be as spe

37、cified in the contract or order. Source of Government Documents. documents are available from: Copies of Military and Federal Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonaovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tabl

38、es For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 11 West 42nd Street, New York, NY 10036.) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55212 7777774 OLYY580 Tob A-A-55 2

39、12 ASTM D 1424 - s ASTM D 1683 - ASTM D 3775 - ASTM D 3776 - Tearing Strength Breaking Strength Yarns Per Inch Weight T (Applications for copies should be addressed to American . - Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) AATCC Test Methods (Applications for copi

40、es should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215) Custodian: Army - GL User Activity: Navy-MC Civil Agency Coordinating Ac tivi ty : GSA - FSS Preparing Activity: DLA - CT Project No. 8410-0818 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55212 9993974 DI144581 942 9 A-A-552 12 ? Figure 1. Belt, All Weather Coat, Wornen,s 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-