DLA A-A-55218-1993 SHIRT WOMEN-S DRESS WHITE (SHORT SLEEVE)《女性服装白色短袖上衣》.pdf

1、. U. A-A-55218 9999974 0244888 T4T 1 INCH-POUND I A-A-55 2 18 1 JULY 93 COMMERCIAL ITEM DESCRIPTION SHIRT, WOMENS, DRESS, WHITE (SHORT SLEEVE) The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-S-87055. Abstract. This specification cov

2、ers the requirements for a womans short sleeve dress shirt, with shoulder epaulets, made of a polyester/cotton blend fabric. Its use is intended for wear by female military personnel of the Navy. Salient Characteristics. The short sleeve shirt shall be a two-piece princess style front and a one piec

3、e back, seven (7) button front closure, breast patch pockets with button down flaps, a convertible collar with collar stays and two (2) shoulder epaulets. The topcollar, top collarstand, top epaulets and top pocket flaps shall be fused. NOTE: See figures 1 and 2. Beneficial comments (recommendations

4、, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the self-addressed Standardization

5、 ocument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5

6、5218 9Y99974 0344889 986 A-A-55 2 18 Material. Patterns. The government shall furnish a single size pattern. The contractor is responsible for grading patterns for additional sizes. The pattern generally provides for a seam allowance of 1/4 inch for joining seams except for the front seam which shal

7、l be 3/8 inch. Minor modification are permitted where necessary when using automatic equipment. Basic Material. The basic material shall be a polyester/cotton blend poplin, plain weave, white shade No. 3013, arid the standard sample is piece number 88064. The finished cloth shall match the standard

8、and be equal to or better than the standard sample with respect to all characteristics. The Basic Material shall be tested using all The Federal and Commercial Test Methods listed below. Table I I Characteristics however, stitches used for multioperations/8-l0 stitches per inch may be used if it doe

9、s not change the furnished measurements, or basic design. O TABLE III Back stitching Top Pocket corners may be tacked w/triangle tack Stitching Collarstand top Collar Front to side front Pocket to breast Pocket Flap position (raw edge) stitch flap to shirt Epaulet Buttonholes Top right-1 (horizontal

10、) right front-6 (vertical) Epaulets-2 (Horizontal) Pocket flaps-1 (vertical) Finished Pocket Pocket Flaps Epaulets widths not less than 1/4“ at the end of all seams not caught in other seams by stitching triangle base shall be: 1/8“ to 3/16“ at the top of pocket triangle apex shall be: 1/2“ to 3/4“

11、below the top of pocket 3/16“ from turned edge 1/16“ from folded edge 3/16“ from folded edge 1/16“ from folded edge 1/16“ from folded edge 1/2“ 11 1/16“ from pocket top 1/8“ to 3/16“ from raw edge 5/16“ from folded edge 1/16“ from folded and pointed edge 5/8“ 2 1/16“ from finished edge 3/4“ 2 1/16“

12、from folded edge 5/16“ + 1/16“ from pointed edge 1/2“ -1/16“ from pointed edge 4-3/4“ -+ 1/8“ vertical length 4-1/4“ 2 1/16“ width 4-3/8“ 2 1/16“ width 1-3/8“ 5 1/16“ vertical length at sides 2“ - + 1/16“ ,vertical length at center 1-1/2“ 2 1/8“ at bottonhole 1-3/4“ +. 1/8“ at armhole seam Note: cen

13、ter epaulets with squared end 1/4“ 2 1/16 forward of the shoulder seam, and the pointed end 1/4“ to 3/8“ below the raw edge of the neck line. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55218 9999974 01441393 307 +* A B C D -Ticket Si z e B

14、ust Lenuth Sleeve Lenuth Collar -Bust Collar 32 12 37-3/4 27-1/8 4-1/4 12 32 13 37-3/4 27-1/2 4-1/4 13 34 12 39-3/4 27-1/8 4-1/4 12 34 13 39-3/4 27-1/2 4-1/4 13 34 14 39-3/4 27-7/8 4-1/4 14 34 15 39-3/4 28-1/4 4-1/4 15 36 13 41-3/4 27-1/2 4-1/4 13 36 14 41-3/4 27-7/8 4-1/4 14 36 15 41-3/4 28-1/4 4-1

15、/4 15 38 13 43-3/4 27-1/2 4-1/4 13 38 14 43-3/4 27-7/8 4-1/4 14 38 15 43-3/4 28-1/4 4-1/4 15 38 16 43-3/4 28-5/8 4-1/4 16 40 14 45-3/4 27-7/8 4-1/4 14 40 15 45-3/4 28-1/4 4-1/4 15 40 16 45-3/4 28-5/8 4-1/4 16 42 15 47-3/4 28-5/8 4-1/4 15 42 16 47-3/4 28-5/8 4-1/4 16 A-A-552 18 Sizes and Measurements

16、. The finished shirt shall conform to the measurements below. Table IV 1 Tolerances - +1/2 - +1/2 - +1/4 - +1/4 NOTE: Refer to figure 1 and 2 for A, B, C, D. All measurements shall be taken with the shirt buttoned, laid flat and smooth. A. Bust. Twice the measurement taken across the front at the ba

17、se of the armhole from folded edge. B. Back Lenuth. Back length shall be taken along the center of the back from the under collar seam to the bottom of the shirt. C. Sleeve Lenuth. Measurement shall be taken along the inseam, from underarm seam to bottom edge of sleeve. D. Collar. Measurement shall

18、be taken from between the end points of the junction of the collar and the collarstand, with the collar in flat position. Label/Markinq. The label/marking shall be as follows: Size stamp will be indicated as follows; 34B-15N (example) Stock number-8410-00-000-0000 (example) O 6 Provided by IHSNot fo

19、r ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55218 m 9999974 0344894 243 m A-A-5 5 2 18 Combination Label shall be centered and stitched to left front facing on inside of shirt around all four sides, 1/8 to 3/16 inch from the edge. The label shall finish face side

20、 up, with the top edge parallel to the folded front edge of facing and the side edge approximately 1 t 2 inches from the bottom edge of shirt. All of the printing shall be clearly visible. e NAME : SERVICE NO: SHIRT, WOMANS, DRESS, WHITE (SHORT - SLEEVE) FIBER CONTENT: POLYESTER (65%) - COTTON (35%)

21、 CONTRACT NO: DLA 100-00-0-0000 NAME OF MANUFACTURER: (if other than the contractor) LAUNDERING INSTRUCTIONS Machine Wash, Hot water Tumble Dry, Medium Heat Remove immediately, or use NAVY FORMULA I NAVEDTRA 414-01-45-81, Product Demonstration Model. When required, offerers shall submit samples of t

22、heir intended production. The Product Demonstration Model will consist of units independently evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model a

23、pproved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance w

24、ith the Commercial Item Description specified above. developed. Product Demonstration Models will be analyzed and Requlatory Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality Assurance Certifi

25、cation. The contractor shall certify that the product offered meets all the characteristics of this commercial item description and that the product conforms to the producers om drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of

26、 such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acce

27、ptance comply with all requirements of the contract. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-552LB W 9999974 0344895 38T W A-A- 5 5 2 18 Examination. The shirt lots shall be inspected in accordance with “Sampling Procedures and Tables f

28、or Inspection by Attributes”, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The shirts shall be examined for the defects listed below. The lot size shall be expressed in units of 100. The sample unit is one shirt. The inspection level shall be II and the

29、acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 6.5. Defects. The shirts shall be examined for defects in design, materials, and workmanship according to using MIL-STD- 1492C. Dimensional Examination. The finished shirt shall conform to the dimensions specif

30、ied; Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one; the inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. Packaqinu Examination. The fully packaged shipping containers s

31、hall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 1.0. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (ex

32、terior and interior) of improper size, location, or method of application Ma ter ia 1 s Workmanship Content Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapli

33、ng Number of items in container is more or less than required NSN shown on one or more items not as specified on shipping container 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-552113 9999974 0344896 01b M A-A-55 2 18 Palletization Length, w

34、idth, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Preservation, Packinu, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government Documents. Copies of Military and Federal d

35、ocuments are available for: A-A-5 O1 9 9 - THREAD, POLYESTER CORE, COTTON- OR POLYESTER COVERED MIL-C-44296 - CLOTH, FUSIBLES MIL-STD-191 - FEDERAL TEST METHOD STANDARDS MIL-STD-1492C - MILITARY STANDARD; PROVISIONS for EVALUATING QUALITY of MENS SHIRTS Standardization Documents Order Desk Bldg. 4D

36、700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonuovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 11 West 42nd Street, New York, NY 10036-8002.) AATCC

37、- 16 - Colorfastness AATCC - 124 - Appearance of Durable Press (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215) ASTM D3775 - Yarns Per Inch (Woven) ASTM D3776 OPTION C - Weight ASTM D5034-90

38、- Breaking Strength (Grab) 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-552LB = 9999974 0344897 T52 = A-A-55 2 18 (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA

39、19103-1187.) Custodian: NAVY - NU Civil Agency Coordinating Ac tivi ty : GSA - FSS Preparing Activity: DLA - CT Project No. 8410 - 0806 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55218 m 999997Li 0144898 999 m A-A-XXXXX 0 ZONE o 9 i - - - -. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-x A-A-XXXXX . . - I X 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-