DLA A-A-55227-1993 POCKET AMMUNITION MAGAZINE ENLISTED MEN-S M-1923《M-1923型男式弹药库口袋》.pdf

1、A-A-5.5227 9979974 0145468 415 a Salient Characteristics. The construction of the pocket shall conform to Figure 1 and shall be as specified herein. 0 Material A-A-5 52 27 Auqust 19,1993 COMMERCIAL ITEM DESCRIPTION POCKET, AMMUNITION MAGAZINE, ENLISTED MENS, M-1923 The General Services Administratio

2、n has authorized the use of this Commercial Item Description in preference to MIL-P-2343. Abstract. This specification covers a two-compartment pocket, in one type and size, made of camouflage green cotton webbing and designed to accommodate one 7-round magazine for the .45 caliber automatic pistol

3、in each of the two compartments. The pocket is attached to a pistol belt or individual equipment belt by two keepers. Webbins, Cotton. The cotton webbing shall be dyed Camouflage Green 483, water repellent, mildew resistant conforming to the following descriptions: -medium weight webbing (hard textu

4、re) - 3-3/4 inch width, 2.43 oz/ln yd minimum -medium heavyweight webbing 2.25 oz/ln yd minimum - 2-1/4 inch width, Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Cent

5、er, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; d

6、istribution is unlimited. FSC 8465 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-552 2 7 The water repellents shall consist of aluminum salts of saturated carboxylic acids (such as formate, acetate, palmitate or stearate), zirconium salts of su

7、ch saturated carboxylic acids, or a combination of both, mixed with refined mineral and vegetable waxes, titanate esters, or a combination of both. The product shall be applied either in the form of an aqueous emulsion or in the form of a water free solvent solution. The mildew compound applied shal

8、l be copper 8-quinolinolate in solubilized form. 0 Thread, Polyester. The thread shall conform to polyester twisted, soft with non-wicking finish, multiple cord thread with a minimum breaking strength of 16 lbs. The thread shall be dyed Camouflage Green 483 and shall show fastness to weathering equa

9、l to or better than the standard sample. Fastener, Snap. The snap fastener shall be a large curtain type, black in color. The female component shall be regular pronged with clinch plate and the male component shall be stud eyelet base, size 1, except the washer is not required. Rivet, Tubular. The t

10、ubular rivets shall be brass, .123 inch nominal size. The head diameter shall be nominal .313 inch. The rivets shall be given a black chemical finish. The length shall be such as to provide a secure clinch of the assembled components. Keeper, With Slide. The keeper with slide shall conform to type X

11、 of MIL-H-9890. Support, Fastener. The fastener support shall be brass with a dark oxide finish. Markinq. The identification marking shall be applied by direct printing, stamping, or stenciling in the location shown on the figure. The characters shall be approximately 1/4 inch in height, black, well

12、 defined, clearly legible, shall not show smearing, bleeding, or off-setting, and shall not show objectionable strike-through of the cloth. marking shall include the nomenclature IIPocket, Ammo, Magazine“, contract number, stock number, and contractors name. In addition, the letters iiUStl shall be

13、applied in the size and location indicated on the figure and shall also be black in color, made by marking, direct printing, stamping, or stenciling. Label/Taq. Each item shall be individually bar-coded with the type VIII, class 17 label/tag of DDD-L-20. This label/tag shall be located so that it is

14、 completely visible on each item and causes no damage to the item. The Identification Defects. Bar-code omitted or not readable by scanner, Human- Readable Interpretation (HRI) omitted or illegible. Bar-coded type not as specified, code density not as specified. 2 Provided by IHSNot for ResaleNo rep

15、roduction or networking permitted without license from IHS-,-,-zes an1 A-A-55227 W 9999974 0145470 073 W A-A-5 52 2 7 Measurements. The finished pocket shall measurements in Figure 1. form to the Workmanship. After completion, the finished pocket shall be thoroughly cleaned, and all loose thread, li

16、nt, and foreign matter removed. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The product demonstration model will consist of units independently developed. evaluated by the government. Evaluation criteria and basis for award are contained in

17、 the solicitation. Product demonstration models will be retained by the government. One (1) product demonstration model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. advised that the product

18、demonstration model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Product demonstration models will be analyzed and Offerers are Resulatorv Reauirements. The offeror/contractor is encouraged to use recover

19、ed materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality Assurance e Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specificati

20、ons, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor quality assurance systems shall not relieve

21、 the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination. Pocket lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by AttributesIl, ANSI

22、/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The pockets shall be examined for the defects listed below. The lot size shall be expressed in units of pockets. shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units,

23、 shall be 1.5. The sample unit is one pocket. The inspection level 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55227 W 74 0145471 TOT A-A- 5 5 2 2 7 Defects. The pocket shall be examined for the following defects: * Webbinq: Any hole, cut,

24、or tear, color not as specified Not firmly and tightly woven, edges frayed or scalloped Abrasion mark, club, smash, broken end or pick Body or pocket splices, i.e., not one continuous piece Any spot or stain (outside) Thread ends not removed Broken or malformed, failing to serve intended purpose, Ha

25、rdware : finish omitted, corroded areas, burrs or sharp edges Snap Fastener: Clinched excessively tight, cutting surrounding material Clinched loosely, permitting male components to rotate freely in the hole in the fastener support or on female components, socket legs not tightly clinched leaving cl

26、inch plate loose provide a secure closure, or open freely (NOTE: The fastener shall be snapped and unsnapped twice to determine whether parts of fastener separate freely and also effect a secure closure. ) Rivets : Incorrect style Fastener not functioning properly, i.e. fails to snap closed, Clinche

27、d excessively tight, cutting webbing Not securely clinched causing looseness of fastener support Rivet head placed on fastener support side of pocket Not assembled to pocket properly Slide component of keeper jams in open, partly closed, or closed Keeper: position (NOTE: The slide component of the k

28、eeper shall be fully closed and opened twice to determine whether slide operates freely.) Open seam Raw edaes Stitch Tension: Loose, resulting in a loose bobbin or top thread Tight resulting in puckering of webbing Any component part omitted or not as specified One or more rows of stitching omitted

29、Needle chews Mends or darns Thread breaks, skipped stitches or runoffs Components and Assembly: Bodv: at folded portion Bodv, ocket and piece “A*: Markinq: characters not as specified Flap improperly stitched causing distortion or excessive fullness Raw edges of not turned under Marking missing, inc

30、orrect, or illegible, or size of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55227 = 9999974 0145472 946 A-A-5 52 2 7 Dimensions: Any pocket too small, i.e., magazines fail to fit properly into either one of the individual pockets Pocket bo

31、dy or flap too short, causing inability to securely close the snap fastener (NOTE: Fit examination shall be performed with two standard 7 round ammunition magazines for the .45 caliber automatic pistol. The magazines shall be inserted into the individual pockets without effort other than that necess

32、ary to overcome friction between the magazines and the pockets. securely closed.) Measurement of item not as specified. The flap snap fastener shall be Dimensional Examination. The finished pocket shall conform to the dimensions specified. established tolerance shall be classified as a defect. The s

33、ample unit shall be one pocket; the inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Any dimension that is not within the Fit Examination. The fit examination shall be performed with two (2), 4-7/16 inch long X 1-5/16 inch wide X 1/2 inch thic

34、k blocks of wood (Poplar) which shall be inserted into the individual pockets without effort other than that necessary to overcome friction between the magazines and the pockets. The flap snap fastener shall be securely closed. Tne inspection level for fit of ammunition magazines into pocket shall b

35、e S-3 and the AQL, expressed in terms of defects per hundred units, 0.65. The sample unit is one pocket. Packasins Examination. shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2

36、and AQL, expressed in terms of defects per hundred units, shall be 2.5. e See Figure 2. The fully packaged shipping containers EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Materials Workmanship Any component missin

37、g, damaged, or not as specified Inadequate application of components, such as : incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55227 m 7q 0145473 8

38、82 m A-A-552 2 7 EXAMINE DEFECT Content Paletization Number of items in container is more or less than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specif

39、ied Preservation, Packina, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, P

40、A 19111-5094 Sources of Nonsovernment Documents ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection (Applications for copies should be addressed to American By Attributes National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-E 18 - Rockwell Hardness and Rockwell Su

41、perficial Hardness of Metallic Materials t (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I Custodians: Army - G

42、L Navy - NU A-A-55227 Ei 7997774 0345474 719 ? A-A-55227 Review Activity: Navy - MC User Activity: Navy - YD Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0134 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

43、S-,-,-A-A-55227 9999974 0145475 A-A-5 52 2 7 Figure 3 1. Pocket, b55 Ammunition Magazine, Enlisted Mens, M-1923 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-& Q: -J o, O a n O O 3 Figure 2. A-A-55227 9999974 0145476 591 A-A- 5 5 2 2 7 - I , Pocket, Ammunition Magazine, Enlisted Mens, M-1923 .45 Cal. 7-Round Magazine Gage Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-