DLA A-A-55248-1994 MITTEN WELDERS《焊接工露指长手套》.pdf

1、A-A-55248 = 9999974 OLb28L4 TT2 = V i A-A-55 2 4 8 February 17, 1994 COMMERCIAL ITEM DESCRIPTION MITTEN, WELDERS The General Services Administration has authorized the use of this commercial item description in preference to MIL-M-16149. Abstract. This commercial item description covers one type of

2、welders mitten with a one-finger leather gauntlet. The mittens are intended for use by Department of Defense personnel. Classification. for either the left or right hand as specified (see Notes). The mitten shall be procured in one size only, Salient characteristics Description. The mitten shall be

3、of a one-finger slip-on style, consisting of a two-piece leather front (gauntlet and palm), a one-piece leather back, two-piece thumb, welted leather inseams, fabric cuff lining, and a knitted insulated lining on the inside back of mitten extending from the wrist to the tip of the fingers. The mitte

4、n shall also have a leather fourchette between the index finger and the three-finger section. The thumb shall have a leather reinforcement piece attached over the face of the thumb (see Figure i). Leather welts shall be placed in between the following seams: fourchette/one-piece back seam, back thum

5、b/face thumb seam, gauntlet/palm seams, and the front/back seam. be 8-10. The mitten shall be neatly laid-off on a heated form. The minimum and maximum number of stitches per inch shall Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improvin

6、g this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by let

7、ter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55248 9999974 OLh28L5 939 A-A-55 2 4 8 . Materials * Leather. The leather shall be flesh sp

8、lit cattlehide, conforming to Type IV, class 2 or Type VI11 of KK-L-2004, suitable for use in gloves. Elongation requirements shall not apply. Both sides of the leather shall be smooth and free of loose flesh. Middle splits, head splits, belly splits and shoulder splits shall not be used. The color

9、shall be the color resulting from chrome tanning. The leather thickness testing shall be as specified in the contract or order. The thickness of the leather shall be not less than 3.5 ounces nor more than 5 ounces, except for the fourchette and welt strips of the mitten where a minimum of 3 ounces i

10、s permitted. i Thread. The thread for seaming and stitching the mitten shall be cotton, 105 Tex (in accordance with ASTM D204), 4 ply yarn (visual certification) with a minimum breaking strength of 5.0 pounds (in accordance with ASTM D2256), conforming to A-A-52094. Gauntlet lininq. The gauntlet lin

11、ing shall consist of an unbleached cotton duck fabric, or a gauntlet lining fabric composed of two thicknesses of unbleached cotton fabric securely laminated together. The weight of the hard textured unbleached cotton duck fabric shall be between 17.6 ounces per square yard (minimum) 19.4 ounces per

12、 square (maximum) (in accordance with ASTM D3776 option C I/), utilizing plied warp and filling yarns (visual certification). The laminated fabric shall be composed of a cotton twill fabric weighing not less than 3.7 ounces per square yard and a plain weave cotton backing fabric weighing not less th

13、an 1.7 ounces per square yard (in accordance with D3776 option C). The finished fabric (laminated) shall contain not less than 14 ounces per square yard of natural rubber, synthetic rubber, or synthetic resin (in accordance with ASTM D3776 option C l/), and weigh not less than 19.4 ounces per square

14、 yard (in accordance with ASTM D3776 option C l/). I/ All test results on the weight of the basic untreated cloth and finished cloth shall be averaged separately to determine the respective lot average weights. These values shall then be utilized in calculating the percent increase in the finished c

15、loth weight. Results shall be calculated to the nearest 0.1 percent. Hand liner. The inside back of the mitten shall have a knitted fleece fabric liner. The knitted fabric shall have an unbleached cotton ground with a napped wool pile face, shall be light gray in color, and shall weigh not less than

16、 6.0 ounces per square yard (in accordance with ASTM D3776 option C). Label/markinq. Each mitten shall be marked with a combination identification and size label conforming to type III or IV, class 4, of DDD-L-20, except that the size is not applicable. Each mitten shall be marked on the gauntlet li

17、ning (backside) with the printing centered and positioned 1-1/4 (2 1/8) inches from the 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-552 4 8 A-A-55248 = 9999974 0362836 875 = last line to the top edge of gauntlet opening. the marking medium

18、shall be dark blue or black and the markings shall show fastness to accelerated laundering only. the lettering shall be 1/8 2 1/16 inch in height, and the lettering shall bear the following inscription: The color of The size of MITTEN, WELDERS CONTRACT NO: SPO-000-000-0000 (Example) NSN: 8415-00-000

19、-0000 (Example) NAME OF CONTRACTOR: NAME OF MANUFACTURER: (If other than contractor) Fiaure. Figure 1 is furnished for information purposes only. In the case of any inconsistencies between the written document and the figure, the written document shall govern. Sizes and measurements. The finished mi

20、tten shall conform to the measurements below. All measurements are expressed in inches and have a tolerance of 2 1/4 inch. Table I. Finished measurements Measurement Dimension Width of palm (A) 5-1/2 Width of gauntlet cuff opening (B) 7-1/2 Length of thumb (C) 3-3/8 Length of first finger (D) 5-1/2

21、Length of palm (E) 8-1/2 Overall length (F) 15-1/4 Note: Refer to Figure 1 for A, B, C, D, E, and F measurements. A. Measurement taken across palm, approximately 1 inch above thumb crotch, folded edge to folded edge. B. Measurement taken across gauntlet cuff opening, folded edge to folded edge. C. t

22、humb. Measurement taken from thumb crotch to seam tip of D. Measurement taken from tip of the first (index) finger to thumb crotch. E. Measurement taken from tip of mitten to gauntlet palm seam. F. gauntlet cuff. Measurement taken from tip of mitten to top edge of 3 Provided by IHSNot for ResaleNo r

23、eproduction or networking permitted without license from IHS-,-,-A-A-55248 = 9999974 DLb28L7 701 A-A- 5 5 2 4 8 WorkmanshiP. The finished mittens shall conform to the quality of product established by this document. defects shall not exceed the contractors own quality assurance standards and the qua

24、lity assurance standards defined by the technical data in the bid package. The occurrence of Resulatorv reauirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality assurance Certification. The contracto

25、r shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producerIs own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the

26、first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Reliance on contractor quality assurance systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply wit

27、h all requirements of the contract. Certificate of compliance. Unless otherwise specified, a certificate of compliance shall be submitted and will be acceptable for the stated requirements. Where certificates of compliance are submitted, the Government reserves the right to check test such items to

28、determine the validity of the certification. Visual examination. Each mitten shall be examined for the defects listed below. Defects. Any hole, cut, tear, spot or stain (outside); thread ends not removed; any open seam; label/marking omitted, incorrect, illegible, incomplete, or misplaced; measureme

29、nts of mitten not as specified; gauntlet lining not type specified; hand liner not type specified; any thumb, first (index) finger or remaining finger areas distorted or twisted, affecting comfort of wearer; any welt omitted; any welt protruding more than 1/8 inch from finished seam; 3 or more needl

30、e holes or pinholes; needle chews; stitches per inch not as specified; any mitten not neatly laid-off, any operation omitted or not performed as specified; misplaced; leather: any brittle or bony area, thin or weak spot, open vein, wrinkles, grub or tick marks, loose spongy or flanky area; any mend

31、in fabric; improper lamination of lining. bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item; any items not packaged in accordance with contract. 4 Provided by IHSNot

32、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55248 9999774 0162818 648 D A-A-552 4 8 Preservation. Dackins, and markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government documents. documents are availab

33、le from: Copies of military and Federal Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Source of non-Government documents ASTM TEST METHODS (Applications for copies should be addressed to American Society for Testing and Materials, 1916 Race Street, Phil

34、adelphia, PA 19103-1187) Notes Orderinq data O a. Title, number, and date of this document b. Whether mitten is required for left hand or right hand (see Classification.) Cus tod iari : Navy-NU Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8415-0920 5 Provid

35、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55248 rn 9999774 OLb28L 584 rn A-A-5 52 4 a 1 LA- T&=$? I E I F c l i- F OM7- .FIGURE i MITTEN, WELDERS 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-