DLA A-A-55442-1995 JAR SCREW CAP《装有螺旋帽的广口瓶》.pdf

1、A-A-55442 9999974 0366777 964 . INCH-POUND A-A-554 4 2 February 10, 1995 COMMERCIAL ITEM DESCRIPTION JAR, SCREW CAP The General Services Administration has authorized the use of this commercial item description, for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the re

2、quirements for a 1-fluid pint, 16-ounce capacity, screw cap jar for general purposes. 2. SALIENT CHARACTERISTICS. This jar, screw cap, shall be supplied without a metal lid. Any commercially available standard i-pint canning jar may be used. The nominal top inside diameter shall be 3-1/4 inches. Thi

3、s is standard for this type of wide mouth jar. 2.1 Phvsical and chemical properties. This jar, screw cap, shall conform to the requirements of ASTM standard E438, Type I, Class A when tested in accordance with ASTM Test Method EZ28. 3. REGULATORY REQUIREMENTS 3.1 Recovered materials. The offeror/con

4、tractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulati.on (FAR). Beneficial comments, recommendations,-additions, deletions, clarifications, etc. and any data which may improve this document should b

5、e sent to: Defense General Supply Center, ATTN: DGSC-VCA, Richmond, VA 23297-5610. AMSC-N/A FSC 8125 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55442 9999974 O

6、Lbb778 8TO A-A-554 4 2 3.2 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest version of FED-STD-376, Preferred

7、 Metric Units for General Use by the Federal Government, and all other requirements of this commercial item description, including form, fit, and function, are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a reque

8、st should be made to the contracting officer to determine if the product is acceptable. The ccntravting officer has the option of accepting or rejecting the product. 4. QUALITY ASSURANCE PROVISIONS 4.1 Contractor certification. The contractor shall certify and maintain substantiating evidence that t

9、he product offered meets the salient characteristics of this commercial item description, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices, and is the same product offered for sale in the commercial marketplace. The government re

10、serves the right to require proof of such conformance prior to first delivery, and thereafter, as may be otherwise provided for under the provisions of the contract. 5. PRESERVATION, PACKAGING, PACKING, AND MARKING. Preser- vation, packaging, packing, and marking for shipment shall be in accordance

11、with ASTM D 3951, Standard Practice for Commercial Packaging, or as specified in the contract or order. 6. NOTES 6.1 Addresses for obtaininq reference documents. 6.1.1 ASTM documents. ASTM documents may be obtained from the American Society for Testing and Materials, 1916 Race Street, Philadelphia,

12、PA 19103. 6.1.2 Military and federal specifications. Military and federal specifications may be obtained from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4, Section D, Philadelphia, PA 19111-5094. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

13、ut license from IHS-,-,-A-A-5 54 4 2 6.2 Suqqested sources of supply. The following are suggested sources of supply for the item covered by this CID. Competition is not limited to these sources. ALLTRISTA Corp., 301 South High St., Muncie, IN, 47305 Anchor Hocking Glass Co., 2893 W. Fair Ave., Lanca

14、ster, OH 43130 Continental Glass Co., 817 W. Cermak Rd., Chicago, IL 60608 Kerr Glass Co., 1840 Century Park East, Los Angeles, CA 9ii Smith Container Co., 3500 Browns Mill Rd., SE, Atlanta, GA 30354 6.3 Orderinq data. a. Title, number, and date of this CID. b. Specify special packaging requirements

15、. c. Contracting officer may request proof of certification prior to first contract delivery. 6.4 National stock number. 8125-00-695-3297 MILITARY INTEREST: Custodians: Army - SM Navy - SA Air Force - 69 DLA - GS CIVIL AGENCY COORDINATING AGENCY : DLA - GS PREPARING ACTIVITY: DLA - GS Project No. 8125-0381 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-