DLA A-A-55464 A-1994 CONNECTORS ELECTRICAL POWER PLUG HOUSINGS POLARIZED《两极化插头电气连接器》.pdf

1、- A-A-554b4A 9999974 0165419 622 A-A-55464A Auqust 12, 1994 SUPERSEDING A-A-55464 October 1, 1993 COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, POWER, PLUG HOUSINGS, POLARIZED The General Services Administration has authorized the use of this commercial item description (CID). Abstract. connec

2、tor can be used in applications that require crimp to discrete stranded wires, size 14 AWG through 24 AWG. used in military systems needing stringent environmental and electrical requirements. This CID covers the general requirements for connector, power, electrical plug housing. This Connectors cov

3、ered by this CID are intended for commercial/industrial applications and shall not be Part or Identifying Number (PIN). The PIN for A-A-5 5464 I I CID number the CID shall be as shown in the following example: I Dash number Salient characteristics. CID sheet. The electrical connectors shall be in ac

4、cordance with the requirements specified herein. Design, construction, and dimensions. Design, construction, and dimensions shall be as specified on figure i and table I. Operating temperature. Current/voltaae. The operating temperature range shall be from -55OC to 105OC. Current/voltage shall be 60

5、0 V ac at 15 amperes maximum. Maximum rated current that can be carried is limited by the maximum operating temperature of the housing, which is 105OC and maximum temperature rise of contacts, which is 3OOC. size, connector size, contact material, and ambient temperature. Variables shall be consider

6、ed for each application are wire Connector housings. Connector housings are molded from a nylon material UL 94V-O brick red for high impact and dielectric strength. Dielectric withstanding voltage. There shall be no breakdown of the insulating material when subjected to 5000 V ac for one minute betw

7、een adjacent contacts of the mated connector assemblies. Insulation resistance. mated connector assemblies. Insulation resistance shall be loo0 megohms minimum between adjacent contacts of Matins force. Connector mating force shall not exceed 13.34 newtons (3 pounds) solid pin styles and 1.5 pounds

8、for split pin styles, per contact. Unmating force. Connector unmating force shall not exceed 3.11 newtons (0.7 pound) minimum for solid pin styles and 2.22 newtons (0.5 pound) minimum for split pin styles, per contact. Contact retention. When an axial load is applied to the contact at the rate of 13

9、 millimeters (.5 inches)/minute, the contact retention force shall be 66.72 newtons (15 pounds) minimum. Durability. termination resistance, dry circuit shall not exceed 3.6 milliohms. physical damage. Durability shall consist of 50 cycles of mating and unmating and upon completion the There shall b

10、e no indication of AMSC NIA DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55464A m 9999974 OLb5420 344 m A-A-55464A t ,550 c/-. O10 SEE NOTE 2 i ,300 +/-

11、 ,010 SEE NOTE 2 t- i c Configuration A Figure 1. Dimensions and configurations. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55464A m 9999974 OLb542L 280 = Ilnr ,000 +/- O10 SEE NOTE 2 L I Configuration B Figure 1. Dimensions and configurat

12、ions - Continued. 3 A-A-55464A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55464A M 9999974 0165422 117 L I ,300 +/- O10 CEE NOTE 2 1.050 +/- . o10 SEE NOTE 2 1 n LI Configuration C Figure 1. Dimensions and configurations - Continued. 4 Provi

13、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55464A 9999974 OLb5423 053 H e e ,800 +- ,010 SEE NOTE 2 .550 +/-. O10 SEE NOTE 2 k- 1.080 - REF A-A-55464A Configuration D Figure 1. Dimensions and configurations - Continued. 5 Provided by IHSNot for

14、ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-554b4A E 9999974 0165424 T9T E A-A-55464A n r ,800 -e t- +/- ,010 SEE NOTE 2 I REF I n Configuration E Figure 1. Dimensions and configurations - Continued. 6 Provided by IHSNot for ResaleNo reproduction or networking perm

15、itted without license from IHS-,-,-A-A-55464A m 9999974 0165425 926 m A-A-55464A I. 050 +/-. 010 SEE NOTE 2 t- -I +/-.o10 .ao0 SEE NOTE 2 . Configuration F Figure 1. Dimensions and configurations - Continued. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

16、 IHS-,-,-A-A-5546413 I- I t%- ,800 +/- ,010 SEE NOTE 2 7.080 - REF Inches mm .O10 0.25 .300 7.62 .460 11.68 NOTES 1. Dimensions are in inches. Inches mm I Inches mm .550 13.97 I 1.080 27.43 .580 14.73 I 1.3 33.02 .800 20.32 I 2. 3. Unless otherwise specified, tolerances are *.O15 inches. Dimensions

17、indicated is as molded, additional growth due to subsequent moisture absorption may occur. Configuration G Figure 1. Dimensions and configurations - Continued. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-554hYA 9999974 0365427 7T A-A-55464A

18、 Vibration. The connector, or hardware when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening of parts when subjected to vibration of 10-55-10 HZ traversed in 1 minute at 1.52 millimeters (.o6 inch) total excursion for 2 hours in each of three mutually perpend

19、icular planes. The contacts shall evidence no discontinuity greater than IO microsecond and termination resistance, dry circuit, 5 milliohms maximum. Physical shock. The connector, or hardware when assembled to the connector, shall be subjected to 50 GIs at 10 milliseconds; 3 shocks in each directio

20、n applied along the three mutually perpendicular planes, total 18 shocks. The contacts shall evidence no discontinuity greater than IO microsecond and termination resistance, dry circuit, 6.0 milliohms maximum. Thermal shock. The connector, when mated, shall be subjected to 25 cycles between -55OC a

21、nd 85OC. dielectric withstanding voltage; 3.75 milliohms maximum termination resistance, dry circuit. The connector, when mated, shall be subjected to 25 cycles between 25OC and Temperature-humidity cycling. 65C at 95 percent RH, with cold shock at -IOOC during any 5 of the first 9 cycles. Housing l

22、ock strength. Housing lock strength shall be 155.69 newtons (35 pounds) minimum. This section is not applicable to this CID. Regulatory requirements. Quality assurance provisions. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsib

23、le for the performance of all inspection, examination, and test requirements specified herein. his own or any other facilities suitable for the inspection requirements specified herein, unless disapproved by the Government. examinations, or tests set forth in this description where such inspections,

24、 examinations, and tests are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract or purchase order, the contractor may use The Government reserves the right to perform any of the inspections, Contractor certification stat

25、ement. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of this CID, and that the product conforms to the producers own drawings, specifications, standards, quality assurances practices, and is the same as the product provided as a

26、bid sample. the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The Government reserves the right to require proof of such conformance prior to Certificate of compliance. A certificate of compliance shall accompany all parts supplied to this CID.

27、Packaqing. Preservation I packaq i nq, packi nq, labe 1 i nq, and marking. Preservation, packaging, labe 1 i ng, and marki ng shall be as specified in the contract or purchase order. m. process of acquiring the item, but is not mandatory. This section contains relevant information which is useful to

28、 buyers, users and suppliers in the Orderinq data. Acquisition documents should specify the following: a. CID document number and revision and CID PIN. b. Quality assurance provisions. c. Packaging requirements. d. Color (if applicable). Comments. Comments on this CID should be directed to Defense E

29、lectronics Supply Center, 1507 Wilmington Pike, ATTN: DESC-ELDI, Dayton, OH 45444-5270, or telephone (513) 296-5391. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55464A CID dash number o1 02 03 04 05 06 Sources of supply. A suggested source

30、of supply is listed in table I. Additional sources will be added as they become available. Configuration Number of posit ions A 2 B 3 C 4 D 6 E 9 F 12 Table Superseded (old) PIN 87097- 002 O04 006 008 I. Suggested sources of supply. Superseding (new) PIN A-A-55464- 01 02 03 04 CID dash number A-A-55

31、464-01 A-A-55464-02 A-A-55464-03 A-A-55464-04 A-A-55464-05 A-A-55444-06 A-A-55464-07 Vendor commercial PIN 350777-1 350766-1 350779-1 350715-1 350720-1 350735-1 350736-1 Vendor CAGE number 00779 00779 00779 00779 00779 00779 00779 Ordering data. Supersession data. Supersession data shall be specifie

32、d on table II. Table 11. Supersession data. O1 4 07 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c O A-A-55464A = 9999974 OLb5429 571 D A-A-55464A Vendor CAGE number Vendor name and address 00779 AMP Incorporated P.O. Box 3608 Harrisburg, PA 17105-3608 CIVIL AGENCY COORDINATING ACTIVITY: GCA - 7FXE PREPARING ACTIVITY: DLA-ES (Project 5935-D521) 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-