DLA A-A-55519 3 C-2012 FUSE INCLOSED LINK SUBMINIATURE SURFACE MOUNT (SM) VERY FAST ACTING WITH WRAP AROUND TERMINALS.pdf

1、AMSC N/A FSC 5920 INCH-POUND A-A-55519/3C 9 January 2012 SUPERSEDING A-A-55519/3B 16 May 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET FUSE, INCLOSED LINK, SUBMINIATURE, SURFACE MOUNT (SM) VERY FAST ACTING, WITH WRAP AROUND TERMINALS The General Services Administration has authorized the use

2、of this commercial item description for all federal agencies. The complete requirements for procuring the fuses described herein shall consist of this document and the issue in effect of A-A-55519. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specificati

3、on sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). AA55519 /03 - 001 A CID number Applicable CID specification sheet (two digits) Dash number Opening time Characteristics (see table III) SALIENT CHARACTERISTICS. Interface and physical di

4、mensions. Fuses supplied to this CID specification sheet shall be as specified herein (see figure 1). Electrical specifications. See table I. Voltage rating. The voltage rating shall be 125 V ac and 125 V dc maximum. Interrupting ratings. The interrupting ratings shall be as indicated in table II. O

5、pening time characteristics. The opening time characteristics shall be as indicated in table III. Environmental specifications. Fuses supplied to this CID shall be subject to the following tests and there shall be no electrical or mechanical damage to the fuse. Operating temperature. The operating t

6、emperature shall be -67F ( -55C) to 257F (+125C). Shock. Fuses shall meet shock requirements in accordance with method 213, MIL-STD-202, test condition I (100 gs peak for 6 milliseconds). Vibration. Fuses shall meet vibration requirements in accordance with method 201, MIL-STD-202, (10 Hz - 55 Hz, (

7、06 inch maximum total excursion). Insulation resistance (after opening). The insulation resistance after opening shall be 10,000 ohms minimum at 100 volts in accordance with method 302, MIL-STD-202, test condition A. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

8、se from IHS-,-,-A-A-55519/3C 2 NOTES: 1. Dimensions are in inches. 2. Tolerance is .006 inch (0.15 mm). FIGURE 1. Configuration and dimensions. Inches mm Inches mm .051 1.295 .170 4.32 .065 1.651 .195 4.953 .080 2.032 .285 7.239 .117 2.972 .325 8.255 .118 3.0 Provided by IHSNot for ResaleNo reproduc

9、tion or networking permitted without license from IHS-,-,-A-A-55519/3C 3 TABLE I. Electrical characteristics CID dash number AA55519/03- Ampere rating Nominal resistance cold ohms Nominal melting It A second 001 .0625 7.0 0.000075 002 .125 1.70 0.00163 003 .250 0.665 0.0106 004 .375 0.395 0.0254 005

10、 .5 0.275 0.0546 006 .75 0.166 0.155 007 1.0 0.122 0.281 008 1.5 0.0817 0.650 009 2.0 0.0468 0.421 010 2.5 0.0350 0.721 011 3.0 0.0290 1.23 012 3.5 0.0240 1.65 013 4.0 0.0224 2.35 014 5.0 0.0155 3.90 TABLE II. Interrupting ratings. Ampere (A) range Interrupting rating All ampere ratings 50 amperes a

11、t 125 V ac Resistance to soldering heat. Fuses shall meet resistance to soldering heat requirements in accordance with method 210, MIL-STD-202, test condition B (10 seconds at 500F (260C). Thermal shock. Fuses shall meet thermal shock requirements in accordance with method 107, MIL-STD-202, test con

12、dition B -85F (-65C) to +257F (125C). Moisture resistance. Fuses shall meet moisture resistance requirements in accordance with method 106, MIL-STD-202, with the exception of no load voltage during this test and step 7 shall not be performed. Physical specifications. Materials. Fuses shall have a mo

13、lded plastic body with copper terminals. Soldering parameters. Fuses shall be able to withstand, without electrical or mechanical damage to the fuse, a wave solder of +500F (260C) for 10 seconds maximum, and an infrared solder of +500F (260C) for 30 seconds maximum. Cartridge fuses shall also be abl

14、e to withstand without damage a vapor phase solder of +420F (215C) for 120 seconds maximum. Solderability. Fuses shall meet solderability requirements in accordance with method 208 of MIL-STD-202. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5

15、5519/3C 4 TABLE III. Rating versus opening time. Ampere rating Opening time characteristics Percent of ampere rating Opening time All ampere ratings A 100 percent 4 hours, minimum 200 percent 1 second, maximum B 100 percent 4 hours, minimum 250 percent 5 seconds, maximum PACKAGING. Packaging shall b

16、e as specified in A-A-55519. In addition, inclosed link fuses may be supplied individually or in a quantity of 500 on a 12 mm (.472 inches) wide tape reel in accordance with ECA EIA 481. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification s

17、heet. See classification information for PIN format example. Source of documents. MILITARY STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts, Test Methods for. (Copies of this document is available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document

18、 Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Other Publications ELECTRONIC COMPONENETS ASSOCIATION/ELECTRONICS INDUSTRY ASSOCIATION (ECA/EIA) ECA EIA 481 - 8 mm Through 200 mm Embossed Carrier Taping and 8 mm Suite 500 Chicago, IL 60631-2708 Phone number (800) 999-9445

19、 Facsimile number (847) 391-0753 E-mail: mailto: URL: http:/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55519/3C 6 Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This infor

20、mation is being provided to assist in reducing proliferation in the Government inventory system. TABLE IV. P/N supersession data. CID dash number (see table I) AA55519/03- MFGRs CAGE MFGRs PIN 1/ MFGRs CAGE MFGRs PIN 1/ 001A 61935 3404.0003.11 75915 459.062 001B N/A N/A N/A N/A 002A 61935 3404.0049.

21、11 75915 459.125 002B N/A N/A N/A N/A 003A 61935 3404.0006.11 75915 459.250 003B N/A N/A N/A N/A 004A 61935 3404.0044.11 75915 459.375 004B N/A N/A N/A N/A 005A 61935 3404.0045.11 75915 459.500 005B N/A N/A N/A N/A 006A 61935 3404.0046.11 75915 459.750 006B N/A N/A N/A N/A 007A 61935 3404.0009.11 75

22、915 459001 007B N/A N/A N/A N/A 008A 61935 3404.0047.11 75915 45901.5 008B N/A N/A N/A N/A 009A 61935 3404.0012.11 75915 459002 009B N/A N/A N/A N/A 010A 61935 3404.0013.11 75915 45902.5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55519/3C 7

23、TABLE IV. P/N supersession data - Continued. CID dash number (see table I) AA55519/03- MFGRs CAGE MFGRs PIN 1/ MFGRs CAGE MFGRs PIN 1/ 010B N/A N/A N/A N/A 011A 61935 3404.0014.11 75915 459003 011B N/A N/A N/A N/A 012A 61935 3404.0015.11 75915 45903.5 012B N/A N/A N/A N/A 013A 61935 3404.0016.11 759

24、15 459004 013B N/A N/A N/A N/A 014A 61935 3404.0017.11 75915 459005 014B N/A N/A N/A N/A 1/ The manufacturers P/N shall not be used for acquisition to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products

25、were reviewed and could be replaced by the CID P/N shown. For actual part marking requirements, see the marking paragraph of A-A-55519. National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID specification sheet. The list is for information only and may not

26、 be indicative of all possible NSNs associated with the CID specification sheet. For up to date information on assigned NSNs, please contact the aforementioned DSCC office listed in A-A-55519. TABLE V. NSNs. Dash number (see table I) AA55519/03- NSN Dash number (see table I) AA55519/03- NSN 001A N/A

27、 008A N/A 001B N/A 008B N/A 002A N/A 009A N/A 002B N/A 009B N/A 003A N/A 010A 5920-01-370-2731 003B N/A 010B N/A 004A N/A 011A N/A 004B N/A 011B N/A 005A N/A 012A N/A 005B N/A 012B N/A 006A N/A 013A N/A 006B N/A 013B N/A 007A N/A 014A N/A 007B N/A 014B N/A Provided by IHSNot for ResaleNo reproductio

28、n or networking permitted without license from IHS-,-,-A-A-55519/3C 8 Changes from previous issue. The margins of this CID specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liab

29、ility whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING

30、ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2011-086 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-