DLA A-A-55537 A-2013 NOZZLE OIL BURNER PRESSURE ATOMIZING.pdf

1、AMSC N/C FSC 4530 INCH-POUND A-A-55537A 19 August 2013 SUPERSEDING A-A-55537 30 March 1992 NOZZLE, OIL BURNER, PRESSURE ATOMIZING The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID)

2、covers the general requirements for nozzle, oil burner, pressure atomizing. Nozzle, oil burner, pressure atomizing covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included i

3、n the PIN as shown in the following example (see 7.1). AA55537 - 001 - H30 - A8 - F1 - L CID Dash Spray Nozzle dim Filter Size number number pattern as specified in table III. Class - H30 = Hollow spray pattern; 30 angle of spray; as specified in figure 1 and table VI. Style - A8 = Adapter with 1/8

4、NPT will be furnished with nozzle, as specified in figure 1. Size - L = Long adapter (1.375 inch), as specified in figure 1. filter/strainer - filter or strainer as specified in table V. 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Nozzle, oil burner, pressure atomizing supplie

5、d to this CID shall be as specified herein (see figure 1). 3.1.1 Design and construction. Oil burner nozzles supplied to the CID will be as specified in the order or contract by the PIN. The thread type required on the nozzle adapter and the length of the adapter will be as specified in the order or

6、 contract by the PIN. See figure 1 and tables I, III, IV and V. 3.1.2 Filter or strainer. The nozzle will be furnished with a filter or strainer as indicated in table V. 3.1.3 Materials. All parts will be of materials as listed: Adapter brass Nozzle corrosion resistant steel Filter bronze Screen nic

7、kel copper alloy 3.1.4 Measurement and tolerances. All dimensions are in inches. Tolerances are as follows: Fractional + 0.03125 Angular + 5 3.1.5 Threads. Thread sizes as specified in FED-STD-H28. 3.1.6 Surfaces. The sealing surfaces between the adapter and the nozzle will have a 16 microinch finis

8、h or better. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55537A 3 3.2 Marking. Nozzle, oil burner, pressure atomizing supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on

9、 the unit pack shall be the CID PIN.) 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements,

10、 and promotes economically advantageous life cycle costs. 3.4 Workmanship. Nozzle, oil burner, pressure atomizing shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The

11、 offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID,

12、 conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criter

13、ia are necessary to document the quality of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 5 years. b. The company producing the item must have sold 5000 units meeting this CID in the c

14、ommercial marketplace over the past 5 years. 5.3 Certification. Certification must be done with the procuring activity approval. The contractor shall certify that the product offered meets the salient characteristics of the description and conforms to the producers own drawings, specifications, stan

15、dards, and quality assurance practices, and is the same as the product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract 6

16、. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally pre

17、ferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is

18、 available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). Provided

19、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55537A 4 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these nozzle, oil burner, pressure atomizing to DLA Land and Maritime under the Militar

20、y Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL STANDARD FED-STD-H28 - Screw-Thread Standards for Federal Services (Copies of these documents are available online at http:/quicksearch.dla.mil or from the DLA Document Service

21、s Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094). FEDERAL REGULATIONS FAR Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street,

22、NW, Washington D.C. 20401.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Commercial products. As part of the market analysis and research effort, this CID was co

23、ordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufact

24、urers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 1N0P1 EQUIPMENT PARTS SALES 140 RUTTER RD HALIFAX, PA 17032-9441 Tel: (717) 896-9110 Kory Rothermel Rod Fulkroad 08GG3 WATERBURY PLUMBING & HEATING SUPPLYINC 1344 MERIDEN RD WATERBURY, CT 067

25、05-3671 (203) 756-4411 MICHAEL L DANGELO DANIEL DANGELO Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55537A 5 2P336 APPLIANCE PARTS DISTRIBUTORS, INC. 400 BRISTOL PIKE CROYDON, PA 19021-5453 (215) 785-6282 KATHLEEN M. DOREY KENNETH M. BIEBE

26、R 08QQ4 CCF ENTERPRISES INC. 2449 NW DALLAS ST GRAND PRAIRIE, TX 75050-4971 (972) 660-2114 KELLY COKER 7.7 Government users. To acquire information on obtaining these Nozzle, oil burner, pressure atomizing from the Government inventory system, contact DLA Land and Maritime, ATTN DLA Land and Marit

27、ime Call Center (NAB), P.O. Box 3990, Columbus, OH 432183990 or telephone (614) 692-2271 or (614) 692-3191. 7.8 Legacy. This commercial item description is a replacement for MS49007. MS49007 is canceled as of 18 December 1998 and copies of this document is available online at http:/quicksearch.dla.m

28、il or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094. 7.9 Cross referenced table. TABLE II. Cross referenced table. Old PIN New CID PIN MS49007-05-S60 A-A-55537-05-S60 MS49007-10-H60 A-A-55537-10-H60 MS49007-10-S45 A-A-55537-10-S45 MS49007-11-H

29、30-A4-L A-A-55537-11-H30-A4-L MS49007-11-S60 A-A-55537-11-S60 MS49007-12-SH45 A-A-55537-12-SH45 MS49007-15-H80 A-A-55537-15-H80 MS49007-15-SH60 A-A-55537-15-SH60 MS49007-16-SH80 A-A-55537-16-SH80 MS49007-17-H60 A-A-55537-17-H60 MS49007-19-SH60 A-A-55537-19-SH60 MS49007-21-H80 A-A-55537-21-H80 MS4900

30、7-22-H80 A-A-55537-22-H80 MS49007-22-S30-A8-L A-A-55537-22-S30-A8-L MS49007-23-S90 A-A-55537-23-S90 MS49007-24-SH80 A-A-55537-24-SH80 MS49007-25-SH45 A-A-55537-25-SH45 MS49007-31-H70 A-A-55537-31-H70 MS49007-18-SH80 A-A-55537-18-SH80 MS49007-19-H30 A-A-55537-19-H30 MS49007-18-H45 A-A-55537-18-H45 MS

31、49007-18-S90 A-A-55537-18-S90 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55537A 6 7.10 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiven

32、ess of the changes. FIGURE 1. Nozzle, oil burner, pressure atomizing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55537A 7 TABLE III. Nozzle type. 1/ US gallons per hour, number 2 fuel oil Type Rated GPH at Operating pressure PSI Type Rated G

33、PH at Operating pressure PSI 100 PSI 125 150 175 200 100 PSI 125 150 175 200 01 02 03 04 0.40 0.50 0.60 0.65 0.45 0.56 0.67 0.73 0.49 0.61 0.74 0.80 0.53 0.66 0.79 0.86 0.56 0.71 0.85 0.92 30 31 32 33 34 9.00 9.50 10.00 10.50 11.00 10.06 10.60 11.18 11.70 12.29 11.02 11.70 12,25 12.90 13.47 11.91 12

34、.60 13.23 13.90 14.55 12.73 13.50 14.14 14.90 15.55 05 06 07 08 09 0.75 0.85 1.00 1.10 1.20 0.84 0.95 1.12 1.23 1.34 0.92 1.04 1.23 1.34 1.47 0.99 1.13 1.32 1.45 1.59 1.06 1.20 1.41 1.55 1.70 35 36 37 38 39 12.00 13.80 14.00 15.30 16.00 13.40 15.40 15.65 17.10 17.89 14.70 16.90 17.15 18.70 19.60 15.

35、90 18.30 18.52 20.30 21.17 17.00 19.60 19.79 21.60 22.63 10 11 12 13 14 1.25 1.35 1.50 1.65 1.75 1.39 1.51 1.68 1.84 1.96 1.53 1.65 1.84 2.02 2.14 1.65 1.79 1.98 2.18 2.32 1.77 1.91 2.12 2.34 2.48 40 41 42 43 44 17.50 18.00 19.50 20.00 21.50 19.60 20.12 21.80 22.26 24.00 21.40 22.04 23.90 24.49 26.4

36、0 23.20 23.81 25.80 26.46 28.40 24.80 25.46 27.60 28.28 30.40 15 16 17 18 19 2.00 2.25 2.50 3.00 3.50 2.24 2.52 2.80 3.35 3.91 2.45 2.74 3.06 3.68 4.29 2.65 2.98 3.30 3.97 4.63 2.83 3.18 3.54 4.25 4.95 45 46 47 48 49 22.00 24.00 26.00 28.00 30.00 24.60 26.80 29.07 31.30 33.60 26.94 29.40 31.84 34.30

37、 36.80 29.10 31.80 34.39 37.00 39.70 31.11 34.00 36.77 39.60 42.50 20 21 22 23 24 4.00 4.50 5.00 5.50 6.00 4.47 5.04 5.59 6.15 6.71 4.90 5.51 6.13 6.74 7.33 5.30 5.93 6.61 7.27 7.94 5.66 6.36 7.07 7.78 8.48 50 51 52 53 54 35.00 40.00 45.00 50.00 55.00 39.10 44.70 50.40 55.90 61.50 42.90 49.00 55.20

38、61.30 67.40 46.30 53.00 59.30 66.10 72.70 49.50 56.50 63.70 70.70 77.70 25 26 27 28 29 6.50 7.00 7.50 8.00 8.30 7.26 7.82 8.38 8.94 9.28 7.98 8.58 9.19 9.79 10.20 8.60 9.25 9.91 10.58 11.00 9.20 9.90 10.60 11.31 11.80 55 56 57 58 59 60.00 70.00 80.00 90.00 100.00 67.00 78.20 89.40 100.90 111.90 73.5

39、0 85.70 98.00 110.50 122.50 79.40 92.50 106.00 119.20 132.30 84.00 99.00 113.50 127.50 141.40 1/ Based on oil weighing 7.16 pounds per gallon at 74F and 34 Seconds Saybolt Universal (SSU) viscosity at 100F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

40、-,-,-A-A-55537A 8 Table IV. Nozzle class. Angle of spray Spray pattern Rated capacity GPH at 100 PSI 30 SOLID (S) SEMI-SOLID (SH) HOLLOW (H) .50 TO 24.00 4.50 TO 20.00 .50 TO 8.00 45 SOLID (S) SEMI-SOLID (SH) HOLLOW (H) .40 TO 30.00 2.25 TO 50.00 .50 TO 50.00 60 SOLID (S) SEMI-SOLID (SH) HOLLOW (H)

41、.40 TO 4.00 2,25 TO 50.00 .40 TO 50.00 70 SOLID (S) SEMI-SOLID (SH) HOLLOW (H) .50 TO 60.00 2.25 TO 60.00 .50 TO 35.00 80 SOLID (S) SEMI-SOLID (SH) HOLLOW (H) .40 TO 100.00 2.25 TO 100.00 .40 TO 50.00 90 SOLID (S) SEMI-SOLID (SH) HOLLOW (H) .60 TO 50.00 2.25 TO 50.00 .60 TO 9.50 Provided by IHSNot f

42、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55537A 9 TABLE V. Filter and strainer types. CID PIN code Rated capacity To be furnished with nozzle F1 .40 TO 1.00 POROUS BRONZE FILTER (25 TO 50 MICRONS) F2 .60 TO .85 SCREEN STRAINER 200 MESH F3 1.10 TO 2.00 POROUS

43、BRONZE FILTER (75 TO 100 MICRONS) F4 1.10 TO 10.58 SCREEN STRAINER 100 TO 120 MESH NO 11.00 TO 100.00 NO FILTER Note: The screen strainer can be substituted for the porous bronze filter on the following. flow rates: .40 to 1.00 and 1.10 to 2.00 MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY:

44、Custodians: GSA - FAS Army - AT Navy - SH Preparing activity: Air Force - 99 DLA - CC DLA - CC Review activities: Project 4530-2012-001 Army-AR Navy SA,YD Air Force 71, 84 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-