DLA A-A-55539 B-2013 VEHICLE COVERS AND END CURTAINS.pdf

1、AMSC N/A FSC 2540 INCH-POUND A-A-55539B 9 December 2013 SUPERSEDING A-A-55539A 19 March 2003 COMMERCIAL ITEM DESCRIPTION VEHICLE COVERS AND END CURTAINS The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial

2、item description (CID) covers the general requirements for vehicle covers and end curtains. Vehicle covers and end curtains covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is i

3、ncluded in the PIN as shown in the following example (see 7.1). 2.1 Part or Identification Number (PIN). (see the following example) A-A-55539 - 001 CID number Dash number (See tables III & IV) 2.2 Vehicle top covers. Sizes as shown in table l (with dash sizes 6, 8, 26, 27, 28, 30) 2.3 Vehicle end c

4、overs. Sizes as shown in table lI (with dash sizes 4, 16, 18, 20). 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Vehicle covers and end curtains supplied to this CID shall be as specified herein (see figure 1). Beneficial comments, recommendations, additions, deletions, clarific

5、ations, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432183990, or email fluidflow.dla.mil. Since contact information can change you may want to verify the currency of the address information using the ASSIST Online

6、 database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 2 3.1.1 Design. The fitted covers shall be made in accordance to the dimensions in tables lll and lV as they apply to figures 1, 2, and 3. 3.1.2 Characteri

7、stics. The fitted covers shall have the following characteristics or capabilities: a. Provide a protective barrier against sun, wind, water, sand, dust and dirt for the vehicle body it is mounted on. b. Provided with a means to resist abrasion from the vehicle body and the mounting points and suppor

8、ts. c. Be equipped with adjustable provisions to secure the cover to the vehicle on the sides, front and rear which match the tie down or securing points on the applicable vehicle. d. Be equipped with provisions to roll up and secure the cover while it is mounted on the vehicle. e. Be the color spec

9、ified in the purchase order. f. Be constructed of 19 to 22 ounce material treated to repel water. g. Be made to the dimensions in tables III and IV as they pertain to figure numbers 1, 2 and 3. h. Be marked to indicate which end goes on the front of the intended vehicle. i. Be marked with the manufa

10、cturers part number on the inside cover or end curtain. 3.2 Marking. Vehicle covers and end curtains supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.3 Recycled, recovered, or environme

11、ntally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.4 Workmanship.

12、Vehicle covers and end curtains shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent

13、 practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality ass

14、urance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Certification. Certification must be done with the procuring activity approval. The contractor shall certify that the product offered meets

15、 the salient characteristics of the description and conforms to the producers own drawings, specifications, standards, and quality assurance practices, and is the same as the product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformanc

16、e prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 3 6. PACKAGING. Preservation, packing, and marking shall be as specified in the

17、contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the r

18、equirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.ht

19、m. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory co

20、ntrol, and submission of these vehicle covers and end curtains to DLA Land and Maritime under the Parts Management Advisory Team (PMAT), CAGE code 58536 should be used. 7.4 Source of documents. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-32002 - Cover Material, Vehicle, Coated Tactical and Combat,

21、Heavy-Duty Waterproof (Copies of these documents are available online at http:/quicksearch.mil or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094) FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of these documents are ava

22、ilable online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance pro

23、visions or certification. c. Packaging requirements. 7.6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have

24、commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

25、ense from IHS-,-,-A-A-55539B 4 MFRs CAGE MFRs name and address 1RLH6 Hoffmann Fabricating LLC 909 E Waterman st Wichita, KS 67202-4731 Shala Hoffmann Tel: (316) 262-6041 54799 Breton Industries 1 Sam Straton Rd. Amsterdam, NY 12010 Al Darmofal (518) 842-3030 4K539 Polytechnic Industries Inc. 14 Ro

26、land ave Mount Laurel, NJ 08054-1012 Eric B. Miller Tel: (856) 235-6550 9J595 Weckworth Manufacturing inc 117 Baughman ave Haysville, KS 67060-1305 Loren Watson Tel: (316) 263-3286 3S151 Production Products Manufacturing 1285 Dunn rd Saint Louis, MO 63138-2802 Daniel P Gaffney Tel: (314) 868-3500

27、 15814 C.R. Daniels Inc 3451 Ellicott Ctr Dr. Ellicott City, MD 21043 Chris Lobianco 410-461-2100 2H635 D C Humphry Co 5000 Paschall Ave Philadelphia, PA 19143 (215) 724-8181 Ronald Nissenbaum rbnhumphrys.biz http:/https:/www.humphrys.biz Provided by IHSNot for ResaleNo reproduction or networking p

28、ermitted without license from IHS-,-,-A-A-55539B 5 MFRs CAGE MFRs name and address 56101 John Johnson Co. 274 S WATERMAN AVE Detroit, MI 48209 Mark A. Ficarra (313) 849-5209 http:/ 9G536 Ehmke Manufacturing Co., Inc. 4200 Macalester St. Philadelphia, PA 19124 Robert L. Rosania 215-324-4200, 800-783

29、-2065 (toll free) 7.7 Government users. To acquire information on obtaining these vehicle covers and end curtains from the Government inventory system, contact DLA Land and Maritime, ATTN DLA Land and Maritime Call Center (NAB), P.O. Box 3990, Columbus, OH 432183990 or telephone (614) 692-2271 or

30、(614) 692-3191). 7.8 Legacy. This commercial item description is a replacement for MS51323, MS51324 and MIL-C-13489 for all federal agencies (MS51323, MS51324 and MIL-C-13489 are canceled as of 26 February 1999 and copies of these documents are available online at http:/quicksearch.dla.mil or from t

31、he U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.) 7.9 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes 7.10 PIN supersession data. These

32、 CID PINs supersede the following MFRs PINs as shown in table I through table IV. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE l. Currently procured vehicle top covers. Dash no. Military PIN CID PIN 6 2014122-1 A-A-55539-006 8 MS513

33、23-8 A-A-55539-008 26 7392938 A-A-55539-026 27 2018842-1 A-A-55539-027 28 MS51323-28 A-A-55539-028 30 7085460 A-A-55539-030 TABLE ll. Currently procured end curtains. Dash no. Military PIN CID PIN 4 MS51324-4 A-A-55539-4 16 MS51324-16 A-A-55539-16 18 MS51324-18 A-A-55539-18 20 MS51324-20 A-A-55539-2

34、0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 6 TABLE lll. Vehicle top cover size to cross reference list. DASH NO. 6 26 27 28 30 DIMENSIONS +1/8” A Body Length 176 273 197 176 238 B Body Width 168 176 176 176 200 ROPES 12 20 14 12 16

35、678C 5 5 5 5 5 D 13 12 14 13 16 E 29 23 7/8 25 27 5/8 25 F 36 29 3/8 33 35 34 G 36 29 3/8 33 36 41 H 36 29 3/8 33 37 7/8 37 J - 35 33 - 34 K - 29 3/8 - - 32 L LAST TO END 19 19 1/8 19 20 20 M DRAW ROPE 60 60 60 72 60 MR DRAW ROPE 60 60 60 72 60 NO. BOW PADS 10 20 12 10 14 N LAST TO END 16 15 16 16 1

36、6 P - 29 3/8 - - 33 R - 6 33 - 34 S 36 29 3/8 33 36 37 T 36 29 3/8 33 36 33 U 36 29 3/8 33 36 34 W 36 29 3/8 33 36 33 Y 16 16 16 16 16 Z 35 7/8 39 7/8 39 7/8 39 7/8 39 7/8 AE 8 8 8 8 8 AF 33 29 29 33 41 AG 5/8 1 1 5/8 5/8 AH 24 24 24 24 24 AJ 14 14 14 14 14 AK 2 2 2 2 2 AL 3 3 3 3 3 AM 5/8 5/8 5/8 5

37、/8 5/8 AN 1/8 1/4 1/4 1/8 1/4 AP 3 1/8 3 3 3 1/8 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 7 TABLE lV. Vehicle end curtain size to cross reference list. Dash No. 4 16 18 20 Dimensions 1/8” A 51-1/2 51-1/2 51-1/2 63-1/2 B 83-3/8 90-

38、3/8 90-3/8 90-3/8 C 26-1/8 30-1/8 26-1/2 26-1/2 D 26 22-1/2 18 18 E ROPE 276 276 292 316 F 120 136 120 120 G 10 10 10 11-1/4 J 10-3/4 11-1/8 11-1/4 11-1/4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 8 FIGURE 1. Fitted vehicle cover. Pr

39、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 9 FIGURE 2. Fitted vehicle cover detail. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 10 FIGURE 3. Curtain, vehicular: end. . Pro

40、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55539B 11 MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AT Navy - YD Preparing activity: Air Force - 99 DLA - CC DLA - CC Review activities: Project 2540-2014-001

41、Army-AR Navy MC, SA Air Force 84 DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-