DLA A-A-55563 11 C-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 3 OFFSET (SIDE) MOUNTING HOLES.pdf

1、INCHPOUND AA55563/11C 21 March 2012 Superseding AA55563/11B 14 May 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 3 OFFSET (SIDE) MOUNTING HOLES The General Services Administration has authorized the us

2、e of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item descript

3、ion (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA55563 CID number /11 Applicable CID specification sheet Material # Card holder width/ board thickness (see table I) $ Overall l

4、ength (see table II) AA55563/11#XX AA55563/11#XX& 1/ Manufacturers 2/ Material type Card holder width/board thickness (see table I) Overall length designator (see table II) Finish 3/ CAGE 18915 4/ B # 10 & 35CF7BHT2F B # 15 & 35CF7BHT8F B # 20 & 35CF7BHT8F B # 25 & 35CF7BHT8F B # 30 & 35CF7BHT8F B #

5、 35 & 35CF7BHT8F B # 40 & 35CF7BHT8F B # 45 & 35CF7BHT9F B # 50 & 35CF7BHT10F B # 55 & 35CF7BHT11F B # 60 & 35CF7BHT12F B # 65 & 35CF7BHT13F B # 70 & 35CF7BHT14F B # 75 & 35CF7BHT15F D # 10 G 35CF7CRT2 D # 15 G 35CF7CRT3 D # 20 G 35CF7CRT4 D # 25 G 35CF7CRT5 D # 30 G 35CF7CRT6 .D # 35 G 35CF7CRT7 D

6、# 40 G 35CF7CRT8 D # 45 G 35CF7CRT9 D # 50 G 35CF7CRT10 D # 55 G 35CF7CRT11 D # 60 G 35CF7CRT12 D # 65 G 35CF7CRT13 D # 70 G 35CF7CRT14 D # 75 G 35CF7CRT15 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/11C 6 T

7、ABLE III. Commercial part number supersession data Continued. 1/ See Classification/Part or Identification Number paragraph for symbol representations. 2 The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of

8、 this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “H“, “K“, “C“, “D“, “E“, “F“, “R“, or “J“ are available for this material type (see

9、finish for a description of the designators). 4/ MFG CAGE 18915 the series type is “35CF7“, (with center mounting hole and flare) the letters “B“, “BH“, or “CR“ denotes material type, the letter “T“ denotes card holder width/board thickness (see table I), the numbers “2“ through “15“ denotes card ho

10、lder lengths, and the letter “F“ denotes finish material. Guidance on use of alternative parts with less hazardous or nonhazardous materials. This CID specification sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material

11、 that meets the form, fit, and function requirements of their application. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing Activity: Air Force 85 DLA CC DLA CC Review Activity: Project: 59982011030 Air Force 99 NOTE: The activities listed above w

12、ere interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-