DLA A-A-55563 15 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 3 MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf

1、INCH-POUND A-A-55563/15B 5 September 2012 Superseding A-A-55563/15A 31 January 2002 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 3 MOUNTING HOLES, WITH CONTROLLED INSIDE BEND RADIUS The General Services Ad

2、ministration has authorized the use of this commercial item description (CID) for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. CLASSIFICATION/IDENTIFICATION NUMBER (PIN

3、). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /15 Applicable CID sheet * Material * Card holder width / board thickness (see table

4、I) * * Length (see table II) * Finish (see table III) Example: AA55563/15AC20D is the PIN for a beryllium copper hard, 2.0 inch (51 mm) long, ebonal finished, low profile, open ended, flared entry, card holder having 3 two offset (side) mounting holes. The card guide is designed to accommodate circu

5、it card assemblies with printed board thicknesses of .0937 inch (2.29 mm). SALIENT CHARACTERISTICS. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figure 1, table I, and table II) and meet the general requirements specif

6、ied in CID AA55563. Material type. Materials types shall be defined in of AA55563. The applicable material type designators for this CID specification are “A“ (beryllium copper H, temper TD01), “B“ (beryllium copper HT, temper TH01), or “D“ (stainless steel H). Material thickness. The material thick

7、ness shall be 005 .002 inch (0.13 0.05 mm). Card holder width/board thickness. The card holder width/board thickness shall be defined in table I herein and is shown in figure 1 as dimensions “D“ and “T“. The applicable card holder width/board thickness designators for this CID specification sheet ar

8、e A, B, or C and shall be included in the PIN. Overall length. Overall length is shown in figure 1 as dimension “L“, and is displayed in table II herein. Applicable overall length designators 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70 or 75 shall be included in the PIN AMSC N/A FSC 5998Provided by I

9、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55563/15B 2 Finish. Finish materials types shall be defined in AA55563. Applicable finish materials designators, “C“ (copper plate), “D“ (black ebonal), “E“ (gold plate), “F“ (nickel plate), “H“ (silver plate),

10、“J“ (zinc, yellow chromate), “K“ (no finish), or “R“ (zinc, clear chromate) are available for material type designators “A“ and “B“. Finish designator “G“ (passivate) is the only finish available for material type designator “D“ (stainless steel). The finish designator shall be included in the PIN.

11、Inches mm Inches mm Inches mm Inches mm Inches mm .001 .003 .005 0.03 0.08 0.13 .010 .015 .02 0.25 0.381 0.51 .048 .067 .07 1.22 1.72 1.78 .078 .115 .12 1.98 2.92 3.05 .125 .141 .25 .37 3.18 3.58 6.35 9.39 NOTES: 1. Dimensions are in inches. 2. Millimeter equivalents are given for general informatio

12、n only. 3. Unless otherwise specified, tolerances are .02 inch (0.51 mm), for 2 places and .010 inch (0.25 mm), for 3 places. FIGURE 1. Card holder design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55563/15B 3 TABLE I. Card h

13、older width/board thickness. PIN designator for card holder width / board thickness Fractional equivalent Card holder width 1/ 2/ Dimension “D“ max Board thickness 1/ 2/ 3/ Dimension “T“ ref Inches mm Inches mm A 1/32 .27 6.85 .0312 0.76 B 1/16 .27 6.85 .0625 1.52 C 3/32 .27 6.85 .0937 2.29 1/ See d

14、imensions “D“ and “T“ in view A - A on figure 1. 2/ Do not use card holder width/board thickness, dimensions “D“ or “T“ for PIN construction. 3/ Dimension “T“ is given as reference. TABLE II. Length and hole spacing. 1/ PIN designator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (

15、0.13) Inches mm Inches mm 20 2.0 51 1.75 44.5 25 2.5 54 2.25 57.2 30 3.0 76 2.75 69.9 35 3.5 89 3.25 82.6 40 4.0 102 3.75 95.3 45 4.5 114 4.25 108.0 50 5.0 127 4.75 120.7 55 5.5 140 5.25 133.4 60 6.0 152 5.75 146.1 65 6.5 165 6.25 158.8 70 7.0 178 6.75 171.5 75 7.5 191 7.25 184.2 1/ Dimensions are i

16、n inches. Millimeters are given for information only. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA55563 Holder, Electri

17、cal Card, Metal Card Guide, General Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Provided by IHSNot for Re

18、saleNo reproduction or networking permitted without license from IHS-,-,-A-A-55563/15B 4 Ordering data. Ordering data shall be as specified in AA55563. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacture

19、rs of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufact

20、urers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547

21、086 Facsimile: (858) 7402430 URL: Part number (P/N) supersession data. These CID specification sheet PINs supersedes the following manufacturers P/Ns as shown in table III The CID PINs listed in table III cover the different lengths available. This information is being provided to assist in reducin

22、g proliferation in the Government inventory system. TABLE III. Commercial P/N supersession data. CID PIN; AA55563/15#$ AA55563/15#$& 1/ Manufacturers 2/ Material type () Card holder width/board thickness Overall length ($) Finish (&) CAGE 18915 4/ B # 45 3/ 35CF7BHT9F B # 50 3/ 35CF7BHT10F B # 55 3/

23、 35CF7BHT11F B # 60 3/ 35CF7BHT12F B # 65 3/ 35CF7BHT13F B # 70 3/ 35CF7BHT14F B # 75 3/ 35CF7BHT15F D # 20 G 35CF7CRT4 D # 25 G 35CF7CRT5 D # 30 G 35CF7CRT6 D # 35 G 35CF7CRT7 D # 40 G 35CF7CRT8 D # 45 G 35CF7CRT9 D # 50 G 35CF7CRT10 D # 55 G 35CF7CRT11 D # 60 G 35CF7CRT12 D # 65 G 35CF7CRT13 D # 7

24、0 G 35CF7CRT14 D # 75 G 35CF7CRT15 1/ See classification/identification number herein for symbol representations. 2/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial prod

25、ucts were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “H“, “K“, “C“, “D“, “E“, “F“, “R“, or “J“ are available for this material type. 4/ MFG CAGE 18915 the series type is “35CF7“ (wit

26、h center mounting hole and flare), the letters “B“, “BH“, or “CR“ denotes material type, the letter “T“ denotes card holder width/board thickness, the numbers “4“ through “15“ denotes card holder lengths, and the letter “F“ denotes finish material. Changes from previous issue. Asterisks are not used

27、 in this revision to identify changes with respect to the previous revision, due to the extensiveness of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55563/15B 6 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians:

28、GSA FAS Navy EC Air Force 99 Preparing Activity DLA CC DLA CC Project 59982012029 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-