DLA A-A-55563 26 A-2013 HOLDER ELECTRICAL CARD METAL CARD GUIDE OPEN ENDED WITH 3 MOUNTING HOLES FOR USE WITH HEAT SINKS.pdf

1、 INCHPOUND AA55563/26A 26 June 2013 Superseding AA55563/26 10 May 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, OPEN ENDED, WITH 3 MOUNTING HOLES, FOR USE WITH HEAT SINKS The General Services Administration has authorized the use of this commercial i

2、tem description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of commercial item description (CID) AA55563. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item

3、 description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /26 Applicable CID specification sheet Material H Card holder width/ board thickness XX Length formerly 1/4

4、H), “B“ (beryllium copper of temper TH01; formerly 1/4 HT) or “D“ (stainless steel). The material type designator and shall be included in the PIN. Material thickness. The beryllium copper thickness shall be .008 .002 inch (0.20 0.05 mm). Card holder width/board thickness. The card holder width/boar

5、d thickness is variable and based on the distance the card guide is mounted from the heat sink side wall (see figure 1). To obtain optimum clamping force, the centerline of the card guide installation holes in the heat sink shall be spaced .093 inch (2.36 mm) plus the thickness of the circuit card a

6、ssembly printed board thickness from the side wall. The applicable card holder width/board thickness designator for this CID specification sheet is “H“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/26A 2 Inches mm Inches m

7、m Inches mm Inches mm .003 .005 .02 .067 0.08 0.13 0.51 1.71 .070 .093 .105 .125 1.78 2.36 2.67 3.18 .141 .156 .180 .198 3.58 3.96 4.57 5.03 .250 .310 .520 6.35 7.87 13.21 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerance

8、s are .02 inch (0.5 mm) for two place decimals and .010 inch(0.25 mm) for three place decimals. FIGURE 1. Card holder design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/26A 3 Overall length. Overall length is shown on figu

9、re 1 as dimension “L“, and is displayed in table I herein. Applicable overall length designator “10“, “15“, “20“, “25“, “30“, “35“, “40“, “45“, “50“, “55“, or “60“ shall be included in the PIN. Finish. Finish types shall be defined in AA55563. Applicable finish materials designator “C“ (copper plate

10、), “D“ (black ebonal) “E“ (gold plate), “F“ (nickel plate), “H“ (silver plate), “J“ (zinc, yellow chromate), or “K“ (no finish) or “R“ (zinc, clear chromate) are available for material type designators “A“ (beryllium copper of temper TD01) and “B“ (beryllium copper of temper TH01)“. Finish designato

11、r “G“ (passivate) is the only finish available for material type designator “D“ (stainless steel). The finish designator shall be included in the PIN. Mounting hole spacing. Mounting hole spacing is shown on figure 1 as dimension “M“ and “M/2“. Dimension “M“ and “M/2“ are listed in table I herein. T

12、ABLE I. Length and hole spacing. 1/ 2/ PIN designator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (0.13) Dimension “M/2“ .005 (0.13) Inch mm Inch mm Inch mm 10 1.0 25 .750 19.1 .375 9.53 15 1.5 38 1.25 31.8 .625 15.88 20 2.0 51 1.75 44.5 .875 22.23 25 2.5 64 2.25 57.2 1.125 28.58

13、 30 3.0 76 2.75 69.9 1.375 34.93 35 3.5 89 3.25 82.6 1.625 41.28 40 4.0 102 3.75 96.3 1.875 47.63 45 4.5 114 4.25 108.0 2.125 53.98 50 5.0 127 4.75 120.7 2.375 60.33 55 5.5 114 5.25 133.4 2.625 66.68 60 6.0 152 5.75 146.1 2.875 73.03 1/ Dimensions are in inches. Millimeters are given for general inf

14、ormation only. 2/ Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification/part i

15、dentification number for PIN format example. Source of documents. Commercial Item Description AA55563 Holder, Electrical Card, Metal Card Guide, General Requirements for. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization

16、 Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data as specified in AA55563. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/26A 4 Commercial products. As part of the market analysi

17、s and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID sp

18、ecification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical

19、 Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: Part number (P/N) supersession data. These CID specification sheet PINs supersedes the following manufacturers P/Ns as shown in table II. The CID PINs listed

20、in table II cover the different lengths available. This information is being provided to assist in reducing proliferation in the Government inventory system TABLE II. Commercial part number supersession data. CID PIN; AA55563/26HXX AA55563/26HXX& 1/ Manufacturers 2/ Material type Card holder width/b

21、oard thickness Overall length designator Finish 3/ CAGE 18915 4/ D H 10 G 37C1CR2 D H 15 G 37C1CR3 D H 20 G 37C1CR4 D H 25 G 37C1CR5 D H 30 G 37C1CR6 D H 35 G 37C1CR7 D H 40 G 37C1CR8 D H 45 G 37C1CR9 D H 50 G 37C1CR10 D H 55 G 37C1CR11 D H 60 G 37C1CR12 1/ See classification/part identification num

22、ber for symbol representation. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN

23、s shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “C“, “D“, “E“, “F“, “H“, “K“, “J“, or “R“ are available for this material type. 4/ Manufacturer CAGE 18915 superseded part number suffix “P“ denotes finish material. Guidance on use of

24、 alternative parts with less hazardous or nonhazardous materials. This CID specification sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. C

25、hanges from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contra

26、ctors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/26A 6 MILITARY I

27、NTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS: Army CR Navy EC Preparing activity Air Force 85 DLA CC DLA CC Review activity: Project 59982012056 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-