DLA A-A-55563 4 B-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE CLOSED ENDED WITHOUT FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES.pdf

1、INCHPOUND AA55563/4B 24 August 2011 SUPERSEDING AA55563/4A 31 January 2002 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CLOSED ENDED, WITHOUT FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES The General Services Administration has authorized the use of

2、this commercial item description (CID) for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item descrip

3、tion (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /04 Applicable CID sheet * Material * Card holder width / board thickness (see table I) * * Overall length (See tabl

4、e II) * Finish Example: AA55563/04BC40H is the PIN for a silver plated beryllium copper, 4.0 inch (102 mm) long, narrow profile card guide with two center mounting holes. The card guide is designed to accommodate circuit card assemblies with printed board thicknesses of .094 inch (2.29 mm) and has t

5、wo offset mounting holes. SALIENT CHARACTERISTICS. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figure 1, table I, and table II) and meet the general requirements specified in CID AA55563. Material type. Materials type

6、s shall be defined in AA55563. The applicable material type designators for this CID specification sheet are “A“ (beryllium copper 1/4 H, temper TD01), “B“ (beryllium copper 1/4 HT, temper TH01), or “D“ (stainless steel 1/4 H). The material type designator and shall be included in the PIN. Material

7、thickness. The material thickness shall be .008 inch (0.20 mm). Card holder width/board thickness. The card holder width/board thickness shall be defined in table I herein and is shown in figure 1 as dimensions “D“ and “T“. The applicable card holder width/board thickness designators for this CID sp

8、ecification sheet are A, B, C, or D and shall be included in the PIN. Overall length. Overall length is shown on figure 1 as dimension “L“, and is displayed in table II herein. Applicable overall length designator “20“, “25“, “30“, “35“, “40“, “45“, “50“, “55“, “60“, “65“, “70“, or “75“ shall be inc

9、luded in the PIN. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/4B 2 Finish. Finish materials types shall be defined in AA55563. Applicable finish materials designators “C“ (copper plate), “D“ (black ebonal), “E“ (gold pla

10、te), “F“ (nickel plate), “H“ (silver plate), “J“ (zinc, yellow chromate), “K“ (no finish), or “R“ (zinc, clear chromate) are available for material type designators “A“ and “B“. Finish designator “G“ (passivate) is the only finish available for material type designator “D“ (stainless steel). The fin

11、ish designator shall be included in the PIN. Mounting hole spacing. Mounting hole spacing is shown on figure 1 as dimension “M“. Dimension “M“ is listed in table II herein. Inches mm Inches mm Inches mm Inches mm Inches mm .001 .003 .005 0.03 0.08 0.13 .020 .067 .08 0.51 1.72 2.03 .093 .105 .156 2.3

12、6 2.67 3.96 .180 .198 .250 4.57 5.03 6.35 .310 .330 .500 7.87 8.38 12.7 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm), for 2 places and .010 inch (0.25 mm), for 3 places. FIGURE 1. Card holder

13、design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/4B 3 TABLE I. Card holder width/board thickness dimensions (see figure 1). PIN designator for card holder width / board thickness Fractional equivalent Card holder width 1

14、/ 2/ Dimension “D“ max Board thickness 1/ 2/ 3/ Dimension “ T“ ref Inches mm Inches mm A 1/32 .33 8.38 .0312 0.76 B 1/16 .33 8.38 .0625 1.52 C 3/32 .33 8.38 .0937 2.29 D 1/8 .37 9.40 .1250 3.30 1/ See dimensions “D“ and “T“ in view A A of figure 1. 2/ Do not use card holder width/board thickness, di

15、mensions “D“ or “T“ for PIN construction. 3/ Dimension “T“ is given as reference. TABLE II. Length and hole spacing. 1/ PIN designator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (0.13) Inches mm Inches mm 20 2.0 51 1.75 44.5 25 2.5 54 2.25 57.2 30 3.0 76 2.75 69.9 35 3.5 89 3.25

16、 82.6 40 4.0 102 3.75 95.3 45 4.5 114 4.25 108.0 50 5.0 127 4.75 120.7 55 5.5 140 5.25 133.4 60 6.0 152 5.75 146.1 65 6.5 165 6.25 158.8 70 7.0 178 6.75 171.5 75 7.5 191 7.25 184.2 1/ Dimensions are in inches. Millimeters are given for general information only. NOTES. PIN. The PIN should be used for

17、 Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA55563 Holder, Electrical Card, Metal Card Guide, General Requirements For. (Copies of these documents are availab

18、le online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563

19、/4B 4 Ordering data. Ordering data is as specified in AA55563. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordin

20、ation, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer C

21、AGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 URL: 65884 Sigmation, Incorporated 4549 Gateway Circle Dayt

22、on, OH 454401792 Tel: (937) 4352129 Fax: (937) 4356375 E-mail: URL: Part number (P/N) supersession data. These CID specification sheet PINs supersede the following manufacturers P/Ns in table III as shown. The CID PINs listed in table III cover the different lengths available. This information is

23、being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial P/N supersession data. CID PIN; AA55563/04#$ AA55563/04#$ base material is beryllium copper 1/4 HT, temper TH01, card holder width/board thickness, dimension “D“, is .33 inch (8.38 mm), dimen

24、sion “T“ is .0937 inch (2.29 mm), commonly known as having a board thickness of “3/32“; the overall length is 4.0 inches (76 mm), dimension “L“; and the finish is silver plate. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/4B 6 TABLE III. C

25、ommercial P/N supersession data Continued. 2/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For act

26、ual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “C“, “D“, “E“, “F“, “H“, “J“, “K“, or “R“ are available for this material type (see finish for a description of the designators). 4/ MFG CAGE 18915 the series type is “35-6“, the letters “B“, “BH“, OR

27、 “CR“ denotes material type, the letter “T“ denotes card holder width/board thickness, the numbers “4“ through “15“ denotes card holder lengths, and the letter “F“ denotes finish material. 5/ MFG CAGE 65884 catalog PINs are the same as this CID sheet. See 1/ above. Guidance on use of alternative par

28、ts with less hazardous or nonhazardous materials. This CID specification sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. MILITARY INTEREST

29、S: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Navy EC Air Force 99 Preparing Activity DLA CC DLA CC Project 59982011014 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-