DLA A-A-59115-1998 PAPER MAP AND CHART LITHOGRAPHIC-FINISH ROLLED《滚压石版印刷处理的纸制地图及图表》.pdf

1、METRICA-A-5911521 January 1998COMMERCIAL ITEM DESCRIPTIONPAPER, MAP AND CHART, LITHOGRAPHIC-FINISH, ROLLEDThe General Services Administration has authorized the use of this commercial i tem description,for all federal agencies.1. SCOPE. This commercial item description (CID) covers two types of lith

2、ographic finish paper for use inprinting charts and maps and reflects requirements parallel to those of the United States Government PrintingOffice as expressed in the Paper Schedules compiled by the Joint Committee on Printing (JCP). The paper isshipped in bulk rolls in accordance with the schedule

3、s herein.2. CLASSIFICATION2.1. Type 1. Offset Map, Lithographic-finish (JCP E30), rolled.2.2. Type 2. 50% Chart, Lithographic-finish (JCP E50), rolled.3. SALIENT CHARACTERISTICS3.1. Type 1. Type 1 paper shall conform to Paper Schedule JCP E30, dated July 25,1996 in all respects except asfollows:a. D

4、elivery shall be in rolls. The end of rolls shall be protected. Labels shall not be pasted on the ends ofrolls. Labels shall be pasted on opposite sides of rolls.b. Roll width and diameter shall be selected from the following schedule and shall be cited in the c ontractor purchase order:Width ( 2mm)

5、(1/16 inch) Maximum roll dia.(nom) Basis weight (5%)1105mm (43 inches) 1016mm (40 inches) 90g/m 2 (60 lbs) 1 - see note781mm (30 inches) 1016mm (40 inches) 90g/m 2 (60 lbs) 1 - see note1187mm (46 inches) 1016mm (40 inches) 90g/m 2 (60 lbs) 1 - see note1238mm (48 inches) 1016mm (40 inches) 90g/m 2 (6

6、0 lbs) 1 - see note(Note 1. Basis weight in pounds is derived from equivalent basis weight of 500 sheets, size 25 X 38 inches inaccordance with method T-410 of The Technical Association of the Pulp and Paper Industry (TAPPI).3.2. Type 2. Type 2 paper shall conform to Paper Schedule JCP E50, dated Ja

7、n 20, 1994 in all respects except asfollows:a. Delivery shall be in rolls. The end of rolls shall be protected. Labels shall not be pasted on the ends ofrolls. Labels shall be pasted on opposite sides of rolls.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any d

8、ata which may improvethis document should be sent to: Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 JeffersonDavis Highway, Richmond, VA 23297-5610.AMSC N/A FSC 9310Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-591152b. Roll width

9、 and weight shall be selected from the following schedule and shall be cited in the contractor purchase order:Width ( 2mm)(1/16 inch) Maximum roll dia.(nom) Basis weight (5%)1086mm (42 inches) 1016mm (40 inches) 135g/m 2 (36 lbs) 2 - see note934mm (36 inches) 1016mm (40 inches) 135g/m 2 (36 lbs) 2 -

10、 see note(Note 2. Basis weight in pounds is derived from equivalent basis weight of 500 sheets, size 17 X 22 inches inaccordance with method T-410 of The Technical Association of the Pulp and Paper Industry (TAPPI).3.3. Roll winding. The paper shall be tightly wound at even tension and shall not con

11、tain more than three splicesper roll. Paper shall be free of cuts and wrinkles. The direction for unwinding the roll shall be indicated on theouter wrapper by an arrow symbol stamped near the ends of the roll. The unwind direction shall also be indicatedon each roll end.3.3.1. Splices. Splices shall

12、 be neatly and securely overlap-pasted and shall be made with repulpable adhesivewhich will not permit the splice to separate. The adhesive may be applied from a tape form backing, provided thebacking is removed, leaving only the adhesive component on the splice. The adhesive shall not cause the spl

13、ice toadhere to adjacent laps. The repulpable adhesive shall not allow the splice to separate while passing through adrying oven maintained at 200C. The tails of the splices shall be neatly and evenly removed without damage toadjacent laps. Splices shall be flagged at both ends with projecting color

14、ed markers, which shall not be pasted tothe splice.3.3.2. Caps, cores, and keyways. No keyways, no metal inserts or caps shall be used with the cores. Cores shallconform to U.S. Government Printing Office drawing number G.A. 4540F, dated 04/93. Core diameter shall be78mm +0 / -0.40 mm (3 1 / 16 in.

15、+0 / - 1/64 in.). Unless otherwise specified in the contract or purchase order, cores of type“A“, “B“, or “C“ construction will be acceptable. When specified in the contract or purchase order, non-returnablefiber cores conforming to drawing G.A. 4540F may be used.3.4. Slime holes. The number of slim

16、e holes per roll shall not exceed four. Slime holes larger than 100mm by100mm (4 in. by 4 in.) shall be cut out and replaced by a splice.4. REGULATORY REQUIREMENTS4.1. Recovered materials. The specifications and paper schedules included in this CID shall conform to theMinimum Content Standards cited

17、 in the Paper Recovered Materials Advisory Notice (61 FR 26985) forpurchasing paper and paper products in compliance with section 6002 of the Resources Conservation and RecoveryAct (RCRA) of 1976 (42 U.S.C. 6962). The government reserves the right to require proof of such conformanceprior to first d

18、elivery and thereafter as may be required under the provisions of the contract.4.2. Recycled content labeling. The recycled content shall be marked on the product labels.5. QUALITY ASSURANCE PROVISIONS5.1 Product conformance. The product provided shall meet the salient characteristics of this Commer

19、cial ItemDescription, conform to the manufacturers own drawings, process sheets, specifications, standards, and qualityassurance practices and shall be the same product offered for sale in the commercial market. When specific qualityassurance provisions are specified for any commercial characteristi

20、c the manufacturer shall maintain recordsresulting from his inspection(s) conducted in accordance with the specific quality assurance provisions. Thegovernment reserves the right to require proof of such conformance. The government reserves the right to auditthe manufacturers quality assurance recor

21、ds.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5911535.2. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the manufactureris responsible for the performance of all inspection requirements as specif

22、ied herein or by referenced documentsspecified herein. The manufacturer shall provide and maintain a quality assurance process (inspection system) thatis acceptable to the Government covering the paper to be delivered in accordance with this CID. The qualityassurance system shall be utilized to perf

23、orm all inspections and tests of materials and components prior toincorporation into end product and for such in process controls as necessary to verify conformance of the product tothe requirements stated herein and for such end articles prior to offering them for delivery. The manufacturer isrespo

24、nsible for controlling product quality and for offering to the Government for acceptance only paper thatconforms to contract requirements and for maintaining objective evidence of this performance. The manufacturermay utilize his own inspection and testing facilities or any commercial laboratory acc

25、eptable to the Government.The Government reserves the right to perform any of the inspections set forth in the specifications and paperschedules where such inspections are deemed necessary to assure that product conforms to prescribedrequirements.5.3. Responsibility for compliance. Paper shall meet

26、all requirements described herein. The inspections set forthin this document shall become a part of the manufacturers overall in process inspection system or qualityassurance program. The absence of any inspection requirements in this CID shall not relieve the manufacturer ofthe responsibility of en

27、suring that all products submitted to the Government for acceptance comply with allrequirements herein whether stated directly or by reference. Sampling inspections, as a part of manufacturingoperations, shall be an acceptable practice to confirm conformance to requirements, however, this does notau

28、thorize submission (to the Government for acceptance) of known defective material, either indicated or actual,nor does it commit the Government to accept defective material.5.4. Quality conformance inspection. Unless otherwise specified in the contract or purchase order, sampling shallbe conducted i

29、n accordance with the current edition of the Technical Association of the Pulp and Paper Industry(TAPPI) Method T-400, “Sampling and accepting a single lot of paper, paperboard, containerboard, or relatedproduct.“ The quality conformance inspection shall consist of the inspections and tests listed i

30、n paragraphs 5.4.1through 5.4.1.2 and Table 1.5.4.1. Component and material inspection.5.4.1.1. Caps, cores and keyways. Caps, cores and keyways shall be inspected for conformance to U.S.Government Printing Office drawing number G.A. 4540F, dated 04/93.5.4.1.2. Material. Test methods in Table 1 shal

31、l be used to verify material conformance of the paper types coveredby this CID. The manufacturers test plan shall, as a minimum, include each of the tests included in Table 1below. The alphanumeric citations refer to the methods of the Technical Association of the Pulp and PaperIndustry (TAPPI) unle

32、ss otherwise indicated. The characteristic is listed in the first column, followed by the testmethod in the second column. Tests shall be conducted in accordance with the modifications explained in “TestMethod“ of Table 1. Paper so tested and found not in conformance to the “Precision requirements“

33、specified in theapplicable JCP Paper Schedule, shall be rejected.TABLE 1 CHARACTERISTIC TEST METHODAcidity (pH) T-435 (Use method T-509 for cold extraction)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-591154TABLE 1 (continued)CHARACTERISTIC TE

34、ST METHODBlocking UM-565Take rectangular specimens 45mm X 60mm. Use a top plate and weight such that the total mass is equivalent to 70 g/cm 2 on the specimens for uncoated paper, and 9 g/cm 2 for coated paper. Prepare the specimens by soaking in water at 255 Cfor 15 minutes. Water shall have free a

35、ccess to both sides of each specimen. Remove specimens from the water and gentlyshake to remove excess water from the surface. Stack and allow assembly to dry at 255 C. Proceed with UM-565.Color deviation and variation TIS 0804-04Calculate using the CIELAB equations described in TAPPI TIS 0804-04. M

36、easurements shall be made under the following conditions: Ill D65, 2 degree observer, specular component included. Measure at start and end of roll and in proximity of all splices.Color by spectral reference T-524Cleanliness (dirt) T-437Curl T-466Equilibrium relative humidity T-502Erasing quality T-

37、478 Ink-Erasing Quality of Paper (Available upon requestfrom TAPPI Technical Services Dept.)Folding endurance T-423 (Schopper) or T-511 (M.I.T.)Grain (Machine direction) T-409Grammage (g/m 2 ) T-410Opacity (Type 1 only) T-425Roll size and weight Mea sure roll diameter and width. Record in (mm). Weig

38、h roll to closest 5kg and record.Rosin T-408Smoothness T-538 (Sheffield Method)Stock (fiber analysis) T-401Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-591155TABLE 1 (continued)CHARACTERISTIC TEST METHODSizing T-530Surface T-537Surface shall b

39、e free of lint, fuzz, or any particles which will pick, lift, fluff, or pile on the blanket under normal press conditions.Tearing strength (Type 1 only) T-414 (Elmendorf-Type Method)Thickness (Caliper)(mm) T-411Water resistance (Type 1 only) T-433 (Dry Indicator Method)Writing quality Use any commer

40、cially available ball point or felt tip pen. Characters shall be clear cut and free from feathering.6. PACKAGING6.1. Preservation, packaging, packing, labeling and marking. Preservation, packaging, packing, labeling andmarking shall be as specified in the contract or purchase order.6.1.1. Commercial

41、. In the absence of detailed instructions in the contract or purchase order, preservation andpacking shall be in accordance with ASTM D 3951, Standard Practice for Commercial Packaging.7. NOTES7.1. Referenced documents. Copies of referenced documents are available from:7.1.1. Government documents :S

42、tandardization Documents Order Desk700 Robbins AvenueBuilding 4, Section DPhiladelphia, PA 19111-5094Drawing Number G.A.4540 and Paper Schedules compiled by the Joint Committee on Printing (JCP) are availablefrom:Director, Materials Management Ser viceU.S. Government Printing OfficeRoom A344, Stop M

43、MPPWashington, D.C. 204017.1.2. Non-government documents :ASTM D 3951 may be obtained from: ASTM100 Barr Harbor DriveProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-591156Conshohocken, PA 19428-2959Technical Association of the Pulp and Paper Indu

44、stry (TAPPI) documents are available from:TAPPI PRESSP.O. Box 105113Atlanta, GA 303487.2. Part identification number (PIN). The following part identification numbering procedure is for governmentpurposes and does not constitute a requirement for the contractor. The PIN shall be constructed as follow

45、s:AA 59115 -X - XXXXRoll width (mm)Type (1 or 2)Document numberIndicates CID7.3. Subject term (key word) list.map paper chart paperlithographic offset maplithographic-finishMILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians GSA-FSS/2FYEAir Force - 99Army - GL PREPARING ACTIVITY:Navy - SA DLA-GSReviewer (Project 9310-0122)NIMA - MPProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-