DLA A-A-59132 A-2010 AMYL ACETATE TECHNICAL.pdf

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information

2、can change, you may want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil. AMSC N/A FSC 6810 METRIC A-A-59132A SUPERSEDING 7 June 2010 A-A-59132 30 January 1998 COMMERCIAL ITEM DESCRIPTION AMYL ACETATE, TECHNICAL The General Services Administ

3、ration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers one technical grade of amyl acetate, CH3COOCH24CH3. The Chemical Abstract Service Registry Number (CAS#) for amyl acetate is 628-63-7. 2. SALIENT CHARAC

4、TERISTICS 2.1 Appearance. Amyl acetate shall be a clear liquid, free of sediment and suspended matter, when visually examined in accordance with the following procedure. Pour appreciate 25 mL of the specimen into a clean, dry test tube. Allow to stand for no less than 10 minutes. Examine by transmit

5、ted light for clarity, sediment and suspended matter. 2.2 Chemical and physical requirements. Amyl acetate shall conform to the chemical and physical characteristics of table I when tested as specified therein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

6、 IHS-,-,-A-A-59132A 2 Table I. Chemical and physical characteristics. Characteristics Requirements ASTM Test method Minimum Maximum Color, platinum-cobalt - No. 15 D1209 Odor - No residual D1296(1)Water content, percent by weight - 0.2 D1364 Specific gravity, 20C/20C 0.871 0.879 D891 Nonvolatile mat

7、ter (g/100mL) - 0.005 D1353 Acidity (mg of KOH/g) - 0.28 D1613 Distillation D1078 Initial boiling point at 760 mm pressure (C) 124 - Distillate below 130C, percent by volume - 10 Distillate below 140C, percent by volume - 75 Dry point at 760 mm pressure (C) - 155 Ester content, percent by weight 95

8、- D1617 (1)Residual odor test with 2 hour dry time 3. REGULATORY REQUIREMENTS 3.1 Labeling, packaging and marking. Item shall be labeled, pack and marked in accordance with Title 49 Code of Federal Regulations (CFR), Parts 100 to 185. 3.2 Recovered materials. The offeror/contractor is encouraged to

9、use recovered materials to the maximum extent practicable, in accordance with paragraph 23.4.3 of the Federal Acquisition Regulation (FAR). Unless otherwise specified herein, all equipment, material and articles incorporated in the work covered by this CID are to be new and fabricated using material

10、s produced from recovered materials to the maximum extent possible without jeopardizing the intend use The term “recovered materials” means materials which have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. Unles

11、s otherwise specified, none of the above shall be interpreted to mean that the use of used or rebuilt products are allowed under this commercial item description 3.3 Material safety data sheet (MSDS). An MSDS shall be prepared and furnished in accordance with 29 CFR 1910.1200 and submitted as direct

12、ed in the contract or order at time of acquisition award. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59132A 3 4. PRODUCT CONFORMANCE PROVISIONS 4.1 Product conformance. The products provided shall meet the salient characteristics of this CID

13、, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 4.2 Market acceptability. The product offered must have

14、 been previously sold either to the government or on the commercial market. 5. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order (see 6.2(c). 6. NOTES (This section contains information of a general or explanatory nature which is helpful, but is not mandato

15、ry.) 6.1 Sources of documents. 6.1.1 Copies of ASTM documents may be obtained from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at www.astm.org. 6.1.2 Copies of the CFR and FAR may be obtained from the U.S. Government Printing Office, 732 North Capital Street

16、 NW, Washington, DC 20401-0001 or online at www.gpo.gov. 6.2 Ordering data. Acquisition documents must specify the following: a. Title, number and date of this commercial item description. b. Unit and quantity required. c. Packaging requirements (see 5). 6.3 National stock number (NSN). NSN 6810-00-

17、174-6604 corresponds to this commercial item description. This may not be indicative of all NSNs associated with this document. 6.4 Key words. Alternate names of amyl acetate include: pentyl acetate n-Amyl acetate pentyl ethanoate Acetic acid pentyl ester Acetic acid n-amyl ester Provided by IHSNot

18、for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59132A 4 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians Army EA GSA FAS Air Force 68 Navy AS DLA GS Reviewers Army MD1 Navy OS Preparing Activity: DLA GS3 (Project 6810-2010-007) NOTE: The activiti

19、es listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-