DLA A-A-59200-1998 GRINDING MACHINES SURFACE ROTARY TABLE VERTICAL SPINDLE《立式摘锭轮盘面砂轮机》.pdf

1、A-A-59200 = 90LB054 0000797 500 m Beneficial comments, recommendations, additions, deletions, and clarifications which may improve this document should be sent to: Defense Supply Center Richmond, ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-561 O. r INCH-POUND A-A-5 9200 17 June

2、1998 SUPERSEDING 22 August 1986 MIL-G-80125B COMMERCIAL ITEM DESCRIPTION GRINDING MACHINES, SURFACE, ROTARY TABLE, VERTICAL SPINDLE The General Services Administration has authorized the use of this commercial item description for ail federal agencies. 1. SCOPE. This commercial item description (CID

3、) covers vertical spindle, rotafy table, surface grinding machines. The machines covered by this CID are intended for use in shops and general production plants, for rough and finish grinding with rapid metal removal rates, and to produce flat surfaces on a wide variety of material. 2. CLASSIFICATIO

4、N. The grinding machines shall be of the following types, styles, and sizes. The type, style, and size to be furnished shall be as specified (see 7.2(b). Type: Type I - Manually operated Type II - Automatic cycle Style: Style A - Single spindle, single transitional table Style B - Single spindle, du

5、al transitional table Style C - Single table, single transitional spindle Style D - Single table, dual spindle Size: Sizes are shown in tables I-IV. Licensed by Information Handling Services - A-A-59200 90L8054 0000798 447 9 Size O10 TABLE I. Style A machine sizes. Table diameter, inches Size Table

6、diameter, inches 10 060 60 016 020 026 030 012 I 12 I 066 I 66 16 084 84 20 096 96 26 r o8 108 30 120 120 014 I 036 042 048 14 36 144 144 42 160 160 48 168 168 I 072 I Size 72 Effective grinding width of table, inches 006 012 6 12 TABLE II. Style B machine sizes. Size I Table diameter, inches I TABL

7、E III. Style C machine sizes. Size 1 Table diameter. inches 1 TABLE IV. Stvle D machine sizes. . Width = (outside diameter - inside diameter) + 2 2 Licensed by Information Handling Services A-A-59200 9038054 0000799 383 A-A-5 9200 3. SALIENT CHARACTERISTICS. 3.1 General requirements. The grinding ma

8、chine shall be new and one of the manufacturers current models capable of operation in accordance with the requirements herein. All parts subject to wear, breakage, or distortion shall be accessible for adjustment, replacement, and repair. 3.2 Comuonents. The grinding machine shall include, as a min

9、imum, the following components: 3.2.1 conform to the manufacturers own drawings, specifications, standards, and quality assurance practices; and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Inspection. The

10、grinding machine shall be inspected to determine compliance with all requirements specified in this CID. 5.3 Testing. Unless otherwise specified (see 7.2(ii), the grinding machine shall be tested in accordance with sections 5.3.1 through 5.3.5. 5.3.1 Test setup and conditions. Unless otherwise speci

11、fied (see 7,2(jj), the manufacturer shall be responsible for supplying all tooling and material(s) and shall conduct all tests required by the Government. The manufacturer shall provide test instruments and equipment with calibration traceable to National Institute of Standards and Technology (NIST)

12、 and shall provide certification of calibration as specified (see 7.2(kk). Unless otherwise specified (see 7.2(11), the machine shall be tested in accordance with environmental conditions of 40 to 104 degrees Fahrenheit and 20 to 95 percent humidity. 5.3.2 Operational test. The machine and its suppl

13、ied systems shall be operated in accordance with the manufacturers standard operating procedures for warm-up and run-off checks. The machine shall be operated at no load for not less than 6 hours. Proper operation of all controls and features shall be verified during the trial period. 5.3.3 Alignmen

14、t tests. Alignment shall be verified before and after the performance tests. Changes in alignment shall be cause for rejection. 5.3.4 Performance tests. Unless otherwise specified (see 7.2(mm), the tests listed in sections 5.3.4.2 through 5.3.4.3 shall be conducted in accordance with the manufacture

15、rs recommendations and procedures. 5.3.4.1 Rapid metal removal. Unless otherwise specified (see 7.2(nn), the grinding machine shall be capable of rapid metal removal. Rapid metal removal shall be tested by rough grinding the top surface of a plate(s) of cast iron, and removing the volume of metal pe

16、r minute required in table VI1 of section 3.3. 5.3.4.2 Surface grinding. Eight equal-sized test blocks of cast iron shall be surface ground simultaneously on each machine table. Four blocks shall be positioned equidistant apart 3 to 4 inches fiom the outer periphery of the table. Four blocks shall b

17、e positioned equidistant apart 3 to 6 inches fiom the center or along the inner periphery of the table. The size of the test blocks shall vary in accordance with the size of the machine, so that at least 20 percent of the table area is covered by the test blocks. After finish grinding the first side

18、, the blocks shall be inverted at the same location on the table for the finish grind of the second side. The test results shall be equal to or better than the performance required in table VI1 of section 3.3. 9 Licensed by Information Handling Services - A-A-59200 90L8054 O000806 343 M A-A-59200 5.

19、3.4.3 Surface finish. SAE O1 tool steel hardened to 59-60 on the Rockwell hardness C scale, shall be substituted for the cast iron in two of the test blocks during the surface grinding for testing surface finish requirements. The grinding machine shall produce surfaces with a total roughness no grea

20、ter than shown in table VI1 on the test blocks composed of SAE O1 tool steel. 5.3.5 Optional tests. Optional tests shall be conducted as specified (see 7.2(00). 5.4 Acceptance. Unless otherwise specified (see 7.2p), preliminary and nnal acceptance tests shall be conducted at the manufacturers site.

21、The results of the performance tests shall be compared with the performance requirements shown in tables VI and VIL Failure of the machine to meet the performance requirements shall be cause for rejection. 6. PACKAGING. Preservation, packing, and marking shall be as specified (7.2(qq). 7. NOTES 7.1

22、Referenced documents. 7.1.1 Government documents. Copies of Federal documents may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. 7.1.2 Industry standards. Copies of industry standards referenced in this CID may be obtained from the following

23、addresses: American National Standards Institute (ANSI) ANSI B 1 1.9 Safety Requirements for the Construction, Care, and Use of Grin- Machines ANSI B7.1 Safety Requirements for the Use, Care, and Protection of Abrasive Wheels Application for copies should be sent to the American National Standards I

24、nstitute, 11 West 42nd Street, New York, NY 10036. American Society of Mechanical Engineers (ASME) ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay) Application for copies should be sent to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017. Intern

25、ational Electrotechnicai Commission (IEC) IEC 204-1 Electrical equipment of industrial machines - Part 1 : General requirements Applications for copies should be sent to the American National Standards Institute, 1 1 West 42nd Street, New York, NY 10036. 10 Licensed by Information Handling ServicesA

26、-A-59200 = 90L8054 0000807 28T m A-A-59200 Occupational Safety and Health Association (OSHA) OSHA 1910 Occupational Safety and Health Standards for General Industry (CFR 29 PART 19 1 O) Application for copies should be sent to the U. S. Department of Labor, 200 Constitution Avenue NW, Room 423, Wash

27、ington, DC 20210. National Electrical Manufacturers Association (NEMA) NEMA MG - 1 NEMA standards publication - Motors and Generators Applications for copies should be sent to the National Electrical Manufacturers Association, 1300 North 17th Street, Suite 1847, Roslyn, VA 22209. National Fire Prote

28、ction Association (NFPA) ANSI/NFPA 79 Electrical Standards for Industrial Machinery Applications for copies should be sent to the National Fire Protection Association, One Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101. 7.2 Ordering data. Acquisition documents must speciQ the following: a.

29、b. d. e. f. g. h. C. 1. j- k. 1. m. n. P. 9. r. S. t. U. V. W. X. O. Y- 2. Title, number, and date of this document. Type, style, and size of grinding machine required (see 2). Base requirements, if different (see 3.2.1). Table carriage requirements for verticdangular adjustment, if required (see 3.

30、2.2). Extra table, if required (see 3.2.2). Weight capacity, if different (see 3.2.2). Chuck, if different (see 3.2.3). Wheelhead column, if different (see 3.2.4). Rapid positioning, if different (see 3.2.5). Power actuated tilt option, if required (see 3.2.5). Dynamic spindle braking, if required (

31、see 3.2.5). Grinding wheel type, if different (see 3.2.7). Wheel dresser, if different (see 3.2.8). Manual controls, if different (see 3.2.9.1). Automatic cycle, if different (see 3.2.9.2). Automatic sizing system, if required (see 3.2.9.3). Indicatoddial graduations, if different (see 3.2.9.4). Dig

32、ital readout system, if required (see 3.2.9.5). Digital readout requirements, if different (see 3.2.9.5). Fully automatic lubricating system, if required (see 3.2.10). Coolant system, if different (see 3.2.1 i). Coolant delivery internal to grinding wheel, if required (see 3.2.1 1). Hydraulic system

33、, if required (see 3.2.12). Electrical system conformance, if different (see 3.2.13). Voltage, if different (see 3.2.13). Motor enclosure, if different (see 3.2.14). Il Licensed by Information Handling ServicesA-A-59200 aa. Optional accessories, as specified (see 3.2.15). bb. Performance, if differe

34、nt (see 3.3). cc. Minimum work zone height, as specified (see 3.4). dd. Machine dimensions and weight, as specified (see 3.5). ee. System of units required (see 3.7). ff. Dual system of units, if required (see 3.7). gg. Nameplate, if different (see 3.8). hh. Lubrication plate or chart, if required (

35、see 3.9). ii. Testing, if different (see 5.3). jj. Test responsibility, if different (see 5.3.1). kk. Certification of calibration, as specified (see 5.3.1). 11. Test environmental conditions, if different (see 5.3.1). mm.Performance tests, if different (see 5.3.4). nn. Rapid metal removal, if diffe

36、rent (see 5.3.4.1). 00. Optional test, if required (see 5.3.5). pp. Acceptance, if different (see 5.4). qq. Packaging requirements, as specified (see 6). 7.3 Part identification number (PIN). The following part identification numbering procedure is for Government purposes and does not constitute a r

37、equirement for the contractor. A-A-5 9200 -xXXXX Size: (See tables I through IV for list of sizes) Style: A - Style A, Single spindle, single transitional table B - Style B, Single spindle, dual transitional table C - Style C, Single table, single transitional spindle D - Style D, Single table, dual spindle Type: 1 - Type I, Manually operated 2 - Type II, Automatic cycle CID number MILITARY INTERESTS: Custodians Air Force - 99 hy-AL Navy - SH PREPARING ACTIVITY: DLA - GS (Project 3415-0215) Reviewers Air Force - 84 Navy - AS, MC, OS 12 Licensed by Information Handling Services