DLA A-A-59206-1998 PROBE LIGHT KIT INSPECTION [Superseded DLA MIL-P-12001 D CANC NOTICE 1 DLA MIL-P-12001 D DLA MIL-P-12001 C DLA MIL-P-12001 B]《检验用光探针(被替代 DLA MIL-P-12001 D 撤消公告 1.pdf

1、A-A-59206 9018054 OOOObL9 L3T A-A-59206 3 June 1998 SUPERSEDING 29 March 1977 MIL-P-12001D COMMERCIAL ITEM DESCRIPTION PROBE LIGHT KIT, INSPECTION The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item d

2、escription (CID) covers hand-held inspection probe lights intended for use in illuminating inaccessible areas with small clearances. 2. CLASSIFICATION. The lights shall be of the following types and sizes. Type is determined by the power source. Size is determined by the reach, which is the distance

3、 from the handle to the light. The type and size to be furnished shall be as specified (see 7.2(b). Type I - Battery powered Type II - Cord connected (120 volts ac, single phase, 60 hertz) Size 1 - 4 inches Size2 - 6inches Size3 - 9inches Size 4 - 12 inches Size 5 - 18 inches Size 6 - 24 inches Size

4、 7 - 27 inches Size 8 - 36 inches Size 9 - 42 inches Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: Defense Supply Center Richmond, ATN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610.

5、 AMSC NIA FSC 6230 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-5920b 9038054 0000b20 953 A-A-59206 3. SALIENT CHARACTERISTICS 3.1 General reauirements. The lig

6、ht shall produce a forward-directed beam of illumination emanating from the end of an extension arm. The light without batteries shall weigh not more than 2.5 pounds. When specified (see 7.2(c), the light shall have the capability to adjust the beam between broad and pinpoint. The type II light shal

7、l operate fiom a 120-volt ac, single- phase, 60-hertz circuit and shall include 6 feet of 3-conductor SJ-type cord meeting the requirements of Underwriters Laboratory (UL) 62. The plug end of the cord shall meet the requirements of figure 5-15 of National Electrical Manufacturers (NEMA) WD 6. Unless

8、 otherwise specified (see 7.2(d), the type I light shall require not more than two batteries, each not larger than size D. 3.2 Components. The light shall include, as a minimum, the following components: 3.2.1 Handle. The handle shall be not less than 3.5 inches long and shall serve as the battery c

9、ase for the type I light and the power cord inteace for the type II light. When specified (see 7.2(e), the handle shall include a magnet of sufficient strength to affix the light to a fmous surhce. 3.2.2 On-off switch. The on-off switch shall be external to the light and clearly marked. 3.2.3 Extens

10、ion arm. Unless otherwise specified (see 7.2(f), the extension arm shall have a diameter of not greater than 5/8 inch and shall be of a flexible gooseneck design capable of maintaining any desired position. 3.2.4 Lamri. The lamp shall be capable of generating a mean spherical candlepower (MSCP) of n

11、ot less than 0.5. 3.2.5 Inspection mirror. If required, the light shall include an inspection mirror that attaches to the lamp end of the extension arm and shall be of the type and size specified (see 7.2(g). 3.2.6 Carrying: case. Unless otherwise specified (see 7.2 (h), the inspection probe light,

12、extension arm(s), min-or(s), spare lamp(s), and other components, as specified, shall be packaged in a carrying case for easy transport and handling. 3.3 htional commnents. ptional components shall be furnished as specified (see 7.2(i). 3.4 Pedormance. The inspection probe light shall operate when s

13、witched on with the appropriate number and type of batteries installed. The extension arm shall be capable of maintaining its position at all desired adjustments, including fully contracted and fully extended, during normal handling and movement. 4. REGULATORY REQUIREMENTS +- I: 4.1 Recovered materi

14、ais. The offeror/contractor is encouraged to use recovered materiais to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5920b OL805

15、4 0000bZL 898 A-A-59206 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The light shall meet the salient characteristics of this commercial item description, conform to the manufacturers own drawings, specifications, standards, and quality assurance practices, and be the same light offered

16、for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Warranty. Unless otherwise specified (see 7.2(j), the manufacturers standard commercial warranty, terms, and conditions shall apply. 6. PACKAGING. Preservation, packing, and marking shall b

17、e as specified (see 7.2(k) in the contract or purchase order. 7. NOTES 7.1 Sources of documents. 7.1.1 Government documents. Copies of paragraph 24.403 of the FAR may be obtained fiom the Superintendent of Documents, U.S. Government Printing Offce, Washington, DC 20402. 7.1.2 Nong;overnment document

18、s. Copies of industry (voluntary) standards referenced in this CID may be obtained fiom the following addresses: Underwriters Laboratories Inc. (UL) ANSI/UL 62 Flexible Cord and Fixture Wire Applications for copies should be sent to: Undenniters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL

19、60062. National Electrical Manufacturers Association (NEMA) ANSINEMA WD 6 Wiring Devices-Dimensional Requirements Applications for copies should be sent to: National Electrical Manufacturers Association, 1300 North 17th Street, Suite 1847, Rosslyn, VA 22209 7.2 Ordering data. Acquisition documents m

20、ust specifi the following: a. Title, number, and date of this document. b. Type and size of light required (see 2). c. Adjustable light beam, if required (see 3.1). d. Battery requirements, if different (see 3.1). e. Magnet in handle, if required (see 3.2.1). f. Type of extension arm, if different (

21、see 3.2.3). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - A-A-5920b 9038054 0000b22 724 A-A-59206 g. Inspection mirror, specie if required (see 3.2.5). h. Carrying case, if required (see 3.2.6). i. Optional components, if required (see 3.3). j

22、. Warranty, if different (see 5.2). k. Packaging requirements, as specified (see 6). 7.3 Part identification number (PIN). The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor: A-A-59206 - xx Ti size: 1 -4inches 2 -

23、6inches 3 -9inches 4 - 12 inches 5 - 18 inches 6 - 24 inches 7 -27inches 8 -36inches 9 -42inches - Type: A - Type I (Battery powered) B - Type II (Cord connected) CIDnumber MILITARY INTERESTS: Custodians Air Force - 99 Army - CR4 PREPARING ACTIVITY CML AGENCY COORDINATING ACTIVITY GSA-7FXE Navy - OS DLA-GS i I Reviewers Navy - AS, MC (Project 6230- 1062) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-