DLA A-A-59214-1998 JUNCTION BOX EXTENSION JUNCTION BOX COVER JUNCTION BOX (STEEL COATED WITH CORROSION- RESISTANT FINISH) [Superseded NAVY W-J-800 F CANC NOTICE 1 NAVY W-J-800 F NA.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datawhich may improve this document should be sent to: Commanding Officer (Code 15E2), NavalConstruction Battalion Center, 1000 23 rd Avenue, Port Hueneme, CA 93043-4301, by using theStandardization Document Imp

2、rovement Proposal (DD Form 1426) appearing at the end of thisdocument or by letter.AMSC N/A FSC 5975INCH-POUNDA-A-59214May 18, 1998SUPERSEDINGW-J-800FJuly 24, 1992COMMERCIAL ITEM DESCRIPTIONJUNCTION BOX: EXTENSION, JUNCTION BOX; COVER, JUNCTION BOX(STEEL, COATED WITH CORROSION-RESISTANT FINISH)The G

3、eneral Services Administration has au thorized the use of this commercial itemdescription for all Federal agencies.1. SCOPE. This commercial item description (CID) covers sheet-steel junction boxes, junctionbox extensions, and junction box covers for use with rigid metallic, intermediate metallic co

4、nduit,electrical metallic tubing, flexible metallic conduit, armored cable, nonmetallic sheathed cable, andnonmetallic tubing. It does not cover nonmetallic junction boxes, cast metal boxes, conduitbodies, or hinged covered boxes.2. CLASSIFICATION. Junction boxes, extensions, and covers covered by t

5、his commercial itemdescription are of the following type as specified (see 7.2):Type I - Octagon junction box.Type II - Square junction box.Type III - Junction box.Type IV - Device box, sectional type (gangable).Type V - Octagon junction box extension ring.Type VI - Square junction box extension rin

6、g.Type VII - Junction box ring.Type VIII - Covers.Type IX - Device box, welded type (nongangable).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5921423. SALIENT CHARACTERISTICS.3.1 Description . The junction boxes, extensions, and covers specif

7、ied in this commercial itemdescription shall be constructed of steel, coated with corrosion-resistant finish, as specified (see7.2). Styles and sizes shall conform to table I and as specified (see 7.2). All bolts and screwsshall have standard screw threads. Knockouts shall be provided (see table I).

8、 Where applicable,location of knockouts shall be in accordance with standards of NEMA OS-1.3.2 Standard commercial product . The junction boxes, extensions, and covers shall, as aminimum, be in accordance with the requirements of this commercial item description and shall bethe manufacturers standar

9、d commercial product. Additional or better features which are notspecifically prohibited by this commercial item description but which are a part of themanufacturers standard commercial product, shall be included in the junction boxes, extensions,and covers being furnished. A standard commercial pro

10、duct is a product which has been sold oris being currently offered for sale on the commercial market through advertisements ormanufacturers catalogs, or brochures, and represents the latest production model.4. REGULATORY REQUIREMENTS.4.1 Materials . The offeror/contractor is encouraged to use recove

11、red materials to the maximumextent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation(FAR). Unless otherwise specified herein, all equipment, material, and articles incorporated in thework covered by this commercial item description are to be new and fabricated us

12、ing materialsproduced from recovered materials to the maximum extent possible without jeopardizing theintended use. The term “recovered materials” means materials which have been collected orrecovered from solid waste and reprocessed to become a source of raw materials, as opposed tovirgin raw mater

13、ials. Unless otherwise specified, none of the above shall be interpreted to meanthat the use of used or rebuilt products are allowed under this commercial item description.4.2 Metric products . Products manufactured to metric dimensions will be considered on an equalbasis with those manufactured usi

14、ng inch-pound units, provided they fall within specifiedtolerances using conversion tables contained in the latest version of ASTM SI-10(IEEE/ASTM SI-10), and all other requirements of this commercial item description includingform, fit and function are met. If a product is manufactured to metric di

15、mensions and thesedimensions exceed the tolerances specified in the inch-pound units, a request should be made tothe contracting officer to determine if the product is acceptable. The contracting officer has theoption of accepting or rejecting the product.5. QUALITY ASSURANCE PROVISIONS.5.1 Product

16、conformance . The products provided shall meet the salient characteristics of thiscommercial item description, conform to the producers own drawings, specifications, standards,and quality assurance practices, and be the same product offered for sale in the commercialmarket. The government reserves t

17、he right to require proof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5921436. PACKAGING. The preservation, packing, and marking shall be as specified in the contract ororder.7. NOTES.7.1 Source of documents .7.1.1 The Fed

18、eral Acquisition Regulation (FAR) is available from the Superintendent ofDocuments, U.S. Government Printing Office, Washington, DC 20402.7.1.2 ASTM Standard is available from the Society for Testing and Materials, 100 Barr HarborDrive, West Conshohocken, PA 19428-2959.7.1.3 IEEE Standard is availab

19、le from the Institute of Electrical and Electronics Engineers(IEEE), IEEE Service Center, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855-1331.7.1.4 NEMA Standard is available from the National Electrical Manufacturers Association,1300 North 17 th Street, Suite 1847, Rosslyn, VA 22209.7.2 Orderin

20、g data . Acquisition documents should specify the following:a. Title, number, and date of this CID.b. Type of junction box, exte nsion, or cover required (see 2).c. Material finish desired (see 3.1).d. Styles and sizes of junction box, extension, or cover required (see 3.1 and table I).7.3 Supersess

21、ion data . This CID replaces Federal Specification W-J-800F dated July 24, 1992.7.4 Part Identification Number (PIN) . The following part identification numbering procedure isfor government purposes and does not constitute a requirement for the contractor. The PINs tobe used for items acquired to th

22、is description are created as follows:A-A-59214 7 A 2Document identifierTypeSizeStyleThe above PIN if for type 7 (VII - junction box ring), size A (4.00 x 2.13 x 1.50 (102 x 54 x38 millimetre (mm), style 2 (eight 0.50-inch (12.7 mm) side knockouts).Provided by IHSNot for ResaleNo reproduction or net

23、working permitted without license from IHS-,-,-A-A-5921447.5 Metric units . The values stated in either inch-pound units or SI units are to be regardedseparately as standard. Within the text, the SI units are shown in brackets. The values stated ineach system are not exact equivalents; therefore, ea

24、ch system should be used independently of theother. Combining values from the two systems may result in non-conformance with the standard.7.6 Subject term (key word) listing .BoxesElectricalMetallic7.7 Changes from previous issue . Marginal notations are not used in this revision to identifychanges

25、with respect to previous issue due to the extensiveness of the changes.MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians : GSA - FSSArmy - CRNavy - YD1 Preparing Activity :Air Force - 85 Navy - YD1Review Activities : (Project 5975-1158)Army - HDNavy - AS, CG, NWAir Force - 19, 82DLA

26、- GSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-592145TABLE I. Types, sizes and styles of junction boxes,extension rings, and covers .Bottom Side knockoutsType Description Size inch (mm)Styleno.0.50(12.70)0.75(19.05)0.50(12.70)0.75(19.05)1.00

27、(25.40)CableboxI Octagon junction box A 3.25 x 1.50 2 1 4(82.55 x 38.10) 3 1 44 1 2 25 1 2 4B 3.50 x 1.50 6 1 4(88.90 x 38.10) 7 1 2 4C 4.00 x 1.50 8 1 2 4(101.60 x 1.50) 9 3 2 410 5 411 3 2 2 212 1 2 4D 4.00 x 2.13 13 3 2 4(101.60 x 54.10) 14 5 415 3 2 2 216 3 2 417 1 2 418 3 2 4II Square junction

28、box A 4.00x 1.50 2 5 12(101.60 x 38.10) 3 1 4 84 3 2 8 45 3 2 8 46 5 10B 4.00 x 2.13 7 5 12(101.60 x 54.10) 8 1 4 89 3 2 8 410 3 2 811 3 2 812 3 2 1213 1 6 4C 4.69 x 1.50 14 3 2 12(119.06 x 38.10) 15 1 4 1016 3 2 8 417 3 2 10D 4.69 x 2.13 18 3 2 12(119.06 x 54.10) 19 3 2 8 420 3 2 821 3 2 4 422 3 2

29、823 3 2 12III Junction box (nongangable) A 4.00 x 2.13 x 1.50 2 3 8(101.60 x 54.10 x 38.10) 3 1 2Nongangable device box B 4.00 x 2.13 x 1.88 4 3 8(101.60 x 54.10 x 47.63)Handy junction box B 4.00 x 2.13 x 1.88 5 2 6(nongangable) (101.60 x 54.10 x 47.63) 6 3 6Nongangable device box C 4.00 x 2.13 x 2.

30、13 7 3 8(101.60 x 54.10 x 54.10) 8 2 6IV Device box sectional type A 3.00 x 2.00 x 2.00 2 2 6(gangable) (76.20 x 50.80 x 50.80) 3 1 64 1 4B 3.00 x 2.00 x 2.50 5 2 6(76.20 x 50.80 x 63.50) 6 1 2 87 2 48 1 2 4Lateral bracket 9 1 1 8C 3.00 x 2.00 x 2.75 10 2 6(76.20 x 50.80 x 69.85) 11 1 6 4Provided by

31、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-592146TABLE I. Types, sizes and styles of junction boxes,extension rings, and covers - Continued.Bottom Side knockoutsType Description Size inch (mm) Style 0.50 0.75 0.50 0.75 1.00 Cableno. (12.70) (19.05) (12

32、.70) (19.05) (25.40) boxIV Device box sectional type C 3.00 x 2.00 x 2.25 12 1 2 4(gangable) (76.20 x 50.80 x 57.15) 13 1 414 1 415 2 4 2D 3.00 x 2.00 x 2.50 16 1 8(76.20 x 50.80 x 88.90) 17 1 818 1 6 219 1 6 4V Octagon box extension ring A 3.25 x 1.50 2 4(82.55 x 38.10)B 4.00 x 1.50 3 4(101.60 x 38

33、.10) 4 45 2 2C 4.00x 2.13 6 2 2(101.60 x 54.10)VI Square junction box A 4.00 x 1.50 2 12extension ring (101.60 x 38.10) 3 84 8 4B 4.00 x 2.13 5 8 4(101.60 x 54.10) 6 8C 4.69 x 1.50 7 8 4(119.06 x 38.10)D 4.69 x 2.13 7 8 4(119.06 x 54.10) 8 8 49 8VII Handy junction box A 4.00 x 2.13 x 1.50 2 8extensi

34、on ring (101.60 x 54.10 x 38.10)B 4.00 x 2.13 x 1.88 3 8(101.60 x 54.10 x 47.63) 4 6StyleType Description Size inch (mm) no. Other descriptionVIII Cover A 3.25-inch (82.55 mm) 2 Flat blankoctagon box 3 Flat with 0.50-inch (12.70 mm) knockout in centerB 4.00-inch (101.60 mm) 4 Flat blankoctagon junct

35、ion box 5 Flat with 0.50-inch (12.70 mm) knockout in center6 Raised 0.63-inch (15.88 mm) with 0.50-inch (12.70 mm)knockout in center7 Raised 0.50-inch (12.70 mm) with 2.75-inch (69.85 mm)opening8 Raised 0.63-inch (15.88 mm) with 2.75-inch (69.85 mm)opening9 Raised 0.75-inch (19.05 mm) with 2.75-inch

36、 (69.85 mm)opening10 Raised 1.00-inch (25.40 mm) with 2.75-inch (69.85 mm)opening11 Raised 1.25-inch (31.75 mm) with 2.75-inch (69.85 mm)opening12 Raised 0.63-inch (15.88 mm), center blanked for single device13 Flat center blanked for single device14 Flat, single receptacle 1.41-inch (35.72 mm) blan

37、ked hole15 Flat center blanked for duplex receptacleC 4.69-inch square junctionbox16 Flat blank17 For 1.00-inch (25.40 mm) flush device18 Flat with 0.50-inch (12.70 mm) knockout in center19 Raised 0.50-inch (12.70 mm), with 2.75-inch (69.85 mm)opening20 Raised 0.63-inch (15.88 mm), with 2.75-inch (6

38、9.85 mm)openingProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-592147TABLE I. Types, sizes and styles of junction boxes,extension rings, and cover - Continued.StyleType Description Size inch (mm) no. Other descriptionVIII Covers C 4.69-inch (119.

39、06 mm)square junction box21 Raised 0.75-inch (19.05 mm), with 2.75-inch (69.85 mm)opening22 Raised 1.00-inch (25.40 mm), with 2.75-inch (69.85 mm)opening23 Raised 1.25-inch (31.75 mm), with 2.75-inch (69.85 mm)openingD 4.00-inch (101.60 mm)junction box surface24 Raised 0.25-inch (6.35 mm) for toggle

40、 switch25 Raised 0.25-inch (6.35 mm) for duplex receptacle26 Raised 0.50-inch (12.70 mm) for toggle switch27 Raised 0.50-inch (12.70 mm) for single receptacle28 Raised 0.50-inch (12.70 mm) for duplex receptacle29 Raised 0.50-inch (12.70 mm) for two toggle switches30 Raised 0.50-inch (12.70 mm) for t

41、wo duplex receptacles31 Raised 0.50-inch (12.70 mm) for toggle switch and singlereceptacle32 Raised 0.50-inch (12.70 mm) for toggle switch and duplexreceptacle33 Raised 0.50-inch for three gangable device boxes34 Raised 0.50-inch (12.70 mm) for six gangable device boxes35 Raised 0.50-inch (12.70 mm)

42、 for 30 - 50 amp single receptacle36 Raised 0.50-inch (12.70 mm) for 30 amp twist lock singlereceptacle37 Raised 0.50-inch (12.70 mm) for 20 amp receptacle38 Raised 0.50-inch (12.70 mm) for 30 - 50 - 60 amp receptacleE 4.00-inch (101.60 mm) 39 Flat blanksquare junction box flush 40 Flat with 0.50-in

43、ch (12.70 mm) knockout in centermounted 41 Raised 0.50-inch (12.70 mm) with 2.75-inch (69.85 mm)opening42 Raised 0.63-inch (15.88 mm) with 2.75-inch (69.85 mm)opening43 Raised 0.75-inch (19.05 mm) with 2.75-inch (69.85 mm)opening44 Raised 1.00-inch (25.40 mm) with 2.75-inch (69.85 mm)opening45 Raise

44、d 1.25-inch (31.75 mm) with 2.75-inch (69.85 mm)opening46 Raised 0.25-inch (6.35 mm) for one flush device47 Raised 0.50-inch (12.70 mm) for one flush device48 Raised 0.50-inch (12.70 mm) for two flush devices49 Raised 0.63-inch (15.88 mm) for one flush device50 Raised 0.63-inch (15.88 mm) for two fl

45、ush devices51 Raised 0.75-inch (19.05 mm) for one flush device52 Raised 0.75-inch (19.05 mm) for two flush devices53 Raised 1.00-inch (25.40 mm) for one flush device54 Raised 1.00-inch (25.40 mm) for two flush devices55 Raised 1.25-inch (31.75 mm) for one flush device56 Raised 1.25-inch (31.75 mm) f

46、or two flush devicesF Handy junction box 57 Blank cover58 For single receptacle59 For duplex receptacle60 For toggle switch61 Multiple wiring deviceBottom Side knockoutsStyle 0.50 0.75 0.50 0.75 1.00 CableType Description Size inch (mm) no. (12.70) (19.05) (12.70) (19.05) (25.40) boxIX Device box we

47、lded type A 3.00 x 2.00 x 2.50 2 2 6(nongangable) (76.20 x 50.80 x 63.50) 3 1 2 4B 3.00 x 2.14 x 2.84 4 1 2 4(76.20 x 54.37 x 72.23)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The prepar

48、ing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision letter should begiven.2. The submitter of this form must complete blocks 4, 5, 6, and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not b

49、e used to request copies of documents, nor to request waivers, or clarification of requirements on currentcontracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenceddocument(s) or to amend contractual requirements.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-59214 2. DOCUMENT DATE (YYMMDD)9805183. DOCUMENT TITLEJUNCTION BOX: EXTENSION, JUNCTION BOX; COVER, JUNCTION BOX (STEEL, COAT