DLA A-A-59289 B-2010 TERMINAL STUD FEEDTHRU DOUBLE - DOUBLE.pdf

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 5940 DISTRIBUT

2、ION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-59289B 4 Oct 2010 SUPERSEDING A-A-59289A 27 May 2004 COMMERCIAL ITEM DESCRIPTION TERMINAL, STUD, FEEDTHRU, DOUBLE - DOUBLE The General Services Administration has authorized the use of this commercial item descri

3、ption for all federal agencies. 1. SCOPE. This commercial item description (CID) covers a double-double turret, feedthru stud terminal. 2. CLASSIFICATION 2.1 The terminals shall be classified by the dash numbers listed in table I. TABLE I. Dimensional requirements. Dash no. Mounting board thickness

4、A Dia. .002 B .015 C .010 D Dia. .005 E .005 F .005 G .010 H .010 J .010 K .005 L .005 -01 1/64 .072 .186 .062 .093 .020 .050 .038 .164 .062 .062 .037 -02 1/32 .072 .186 .062 .093 .020 .050 .038 .164 .062 .062 .054 -03 .090 .219 .093 .125 .020 .062 .040 .187 .054 .054 .075 -04 .156 .250 .109 .187 .0

5、32 .093 .047 .218 .062 .045 .075 -05 1/16 .072 .186 .062 .093 .020 .050 .038 .164 .062 .062 .084 -06 .090 .219 .093 .125 .020 .062 .040 .187 .054 .054 .105 -07 .156 .250 .109 .187 .032 .093 .047 .218 .062 .045 .105 -08 .262 .500 .219 .312 .032 .187 .125 .437 .156 .155 .105 -09 3/32 .072 .186 .062 .0

6、93 .020 .050 .038 .164 .062 .062 .116 -10 .090 .219 .093 .125 .020 .062 .040 .187 .054 .054 .135 -11 .156 .250 .109 .187 .032 .093 .047 .218 .062 .045 .135 -12 .262 .500 .219 .312 .032 .187 .125 .437 .156 .155 .135 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

7、from IHS-,-,-A-A-59289B 2 TABLE I. Dimensional requirements - continued. Dash no. Mounting board thickness A Dia. .002 B .015 C .010 D Dia. .005 E .005 F .005 G .010 H .010 J .010 K .005 L .005 -13 1/8 .072 .186 .062 .093 .020 .050 .038 .164 .062 .062 .147 -14 .090 .219 .093 .125 .020 .062 .040 .187

8、 .054 .054 .165 -15 .156 .250 .109 .187 .032 .093 .047 .218 .062 .045 .165 -16 .262 .500 .219 .312 .032 .187 .125 .437 .156 .155 .165 -17 5/32 .156 .250 .109 .187 .032 .093 .047 .218 .062 .045 .195 -18 .262 .500 .219 .312 .032 .187 .125 .437 .156 .155 .195 -19 3/16 .156 .250 .109 .187 .032 .093 .047

9、 .218 .062 .045 .230 -20 .262 .250 .109 .187 .032 .093 .047 .218 .062 .155 .230 -21 1/4 .262 .250 .109 .187 .032 .093 .047 .218 .062 .155 .293 3. SALIENT CHARACTERISTICS 3.1 Material. The material shall be half-hard temper brass conforming to one of the following alloys: a. C36000 in accordance with

10、 ASTM International (ASTM) B16/B16M, “Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines“ (DoD adopted). b. C34200 or C35300 in accordance with ASTM B121/B121M, “Leaded Brass Plate, Sheet, Strip, and Rolled Bar“, (DoD adopted). c. C31400 in accordance with ASTM B140/B140M, “Copper-Zinc

11、-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes“ (DoD adopted). 3.2 Workmanship. All surfaces shall be smooth and free of burrs and sharp edges. 3.3 Finish. The finish shall consist of a 0.0003 inch (7.6 microns) thick (minimum) layer of silver plate in accordance with ASTM B700, “Standard

12、 Specification for Electrodeposited Coatings of Silver for Engineering Use“, Grade D, Class N, covered by a 0.000030 inch (0.76 micron) thick (minimum) layer of gold plate in accordance with Society of Automotive Engineers (SAE) AMS 2422D, “Gold Plating“, or equivalent. 3.4 Dimensional requirements.

13、 Dimensional requirements are as listed in table I and figure I. Dimensions are in inches unless otherwise specified. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23

14、.403 of the Federal Acquisition Regulation (FAR). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59289B 3 OPTIONALCONSTRUCTIONOF TURRET ENDSTOP VIEWECBLA F G45FGTURRET ENDSDEHEKJ EEFIGURE 1. Double - double feedthru stud terminal. 5. PRODUCT CON

15、FORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The govern

16、ment reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specifi

17、ed in the acquisition order (see 7.3(c). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. Example of reference part number: AA59289 - 04 Dash number: see table I AA59289 - XX CID number

18、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59289B 4 7.2 Sources of documents. 7.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of FAR documents may be obta

19、ined from http:/www.arnet.gov/far/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm.org/. 7.2.3 SAE standards. Copie

20、s of SAE standards may be obtained from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001. Electronic copies of SAE standards may be obtained from http:/www.sae.org/. 7.3 Ordering data. The acquisition order should specify the following: a. CID document number, revision, and CID P

21、IN. b. Dash number (see 2.1). c. Preservation, packing, and marking (see 6.1). 7.4 Subject term (key word) listing. brass copper gold silver turret MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - MI Navy - AS Air Force - 11 GSA FSS Preparing Activity: DLA GS4 (Project 5940

22、-2010-002) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-