DLA A-A-59308-1998 CLINOMETERS SHIP AND ACCESSORIES《船用测角器及辅助设备》.pdf

1、 A-A-59308 9018054 0003182 366 = IINCH-POUND I 24 AuPust 1998 SUPERSEDING 18 January 1991 A-A-59308 MIL-C-20061D COMMERCIAL ITEM DESCRIPTION CLINOMETERS, SHIP, AND ACCESSORIES The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1.

2、SCOPE. This commercial item description (CID) covers two types and three classes of bubble-in-tube type ship clinometers used for measuring the trim and the heel of ships. 2. CLASSIFICATION 2.1 Types. The clinometers shall be of the following types as specified (see 7.3): Type I - Trim clinometer Ty

3、pe II - Heel clinometer 2.2 Classes. The clinometers shall be of the following classes as specified (see 7.3): Class A - 15 degrees of arc each side of the vertical Class B - 20 degrees of arc each side of the vertical Class C - 60 degrees of arc each side of the vertical Beneficial comments, recomm

4、endations, additions, deletions, clarifications, etc, and any data which may improve this document should be sent by letter to: Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610. AMSC NIA FSC 6605 DISTRIBUTION STATEMENT A. Approved for publi

5、c release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593 08 3. SALIENT CHARACTERISTICS 3.1 Toxic chemicals. hazardous substances, and ozone depletinp. substances CODSI. The use of toxic chemicals, hazardous substa

6、nces, or ODS shall be avoided, whenever feasible. 3.2 MountinP board. The mounting board shall be fabricated fiom plastic or stainless steel. 3.2.1 Type I. The mounting board shall be 14 inches wide and 5 inches high. Along the top edge, there shall be two mounting holes O. 196 inches in diameter. T

7、he holes shall be spaced five-eighths of an inch from the top and each side edge. Along the bottom edge, there shall be one mounting hole 0.196 inches in diameter. The hole shall be located five-eighths of an inch from the bottom and 5 7/8 inches from the left edge. 3.2.2 TyDe II. The mounting board

8、 shall be 17 inches wide and 10 inches high. Along the top edge, there shall be two mounting holes 0.196 inches in diameter. The holes shall be spaced five-eighths of an inch from the top and each side edge. Along the bottom edge, there shall be one mounting hole 0.196 inches in diameter. The hole s

9、hall be located five-eighths of an inch from the bottom and 7 7/16 inches from the left edge. 3.3 Graduations. Centered above each clinometer tube shall be a degree-graduated scale. The zero-degree mark shall be in the center, and the remainder of the degree marks shall be equally spaced to the left

10、 and right of the zero in one-degree increments. Each five-degree mark shall be numbered. The scale shall be permanently marked or affixed on the clinometer. The numerals and the graduations shall be in a contrasting color from the color of the material on which they are placed. 3.4 Accuracy. Any an

11、gular movement of the tube in a vertical plane shall produce a corresponding movement of the bubble within 1 degree for the type I, class A and type II, class B tube; and within 2 degrees for the type II, class C tube. This shall be verified by mounting the clinometer on a dividing head or other cal

12、ibrated stand so that it can be revolved in the vertical plane. The indications shall be observed when the clinometer is displaced fiom the vertical. Five points on each side of the vertical shall be tested. The test shall be performed at a temperature between 153C and 23.9“C. 3.5 Shock. The assembl

13、ed unit shall withstand, without breakage of board or tube(s), Grade By Class I, Type A shock test in accordance with MIL-S-901, Shock Tests, H.I. (High Impact) Shipboard Machinery, Equipment, and Systems, Requirements for. 3.6 Identification. The following information shall be permanently marked, o

14、r affixed, in a contrasting color, on the fiont of the unit: SHIP CLINOMETER TYPE CONTRACTING AGENCY CONTRACT NO. YEAR MANUFACTURERS NAME NSN 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59308 W 9038054 0003184 139 A-A-59308 4. REGULATORY RE

15、QUIREMENTS 4.1 Marking. uackaging. and labeling. Material shall be labeled, packed, and marked in accordance with Title 49, Code of Federal Regulations (CFR) paragraphs 100 to 185. 4.2 Recycled materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practical

16、, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The product provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standard

17、s, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Market acceptabilitv. The item offered must have been sold to the government or commercial market. 6. PACKAGING. Preserva

18、tion, packing, and marking shall be as specified in the contract or order. 7. NOTES (This section contains information of a general or explanatory nature that is helpful, but is not mandatory). 7.1 Part identification number (PIN). The following part identification numbering procedure is for governm

19、ent purposes and does not constitute a requirement for the contractor. AA- 59308 - I A ExampleofPIN: AA59308-IA - Designator for class: A = Class A B = Class B c = Class c Designator for type: I = Type I II = Type II Dash L Commercial item description number Prefix for commercial item description 3

20、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59308 m OL05Y 0003185 075 m A-A-593 08 7.2 Source of documents. 7.2.1 The Code of Federal Regulations and Federal Acquisition Regulation may be obtained fiom the Superintendent of Documents, U.S. G

21、overnment Printing Office, Washington, DC 20402-0001. 7.2.2 Military specifications may be obtained from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191 11-5094. 7.3 Ordering data. Acquisition documents must speciQ the following: 7.3.1 Title, number, an

22、d date of this commercial item description. 7.3.2 Type and class required (see 2). 7.3.3 Packaging requirements (see 6). 7.4 National stock number INSN). The following NSNs correspond to this commercial item description. They may not be indicative of all possible NSNs for this CID. I NSN I Type I Cl

23、ass I Description I I 6605-00-391-4234 I II I da IBoard I 6605-00-391-4235 II 6605-00-752-8791 1- 11 6605-00-752-8792 da C B A Board Tube Tube Tube Tube 7.5 Sources of sumly. The following company produces products known to meet the comercial item description requirements. Competition is not to be l

24、imited to the suppliers on this list. Connecticut Valley Industries Incorporated 8 Center Road Old Saybrook, CT 06475 (860) 388-0822 Navistar Marine Instrument Corporation 2505 West Coast Highway Suite 102 Newport Beach, CA 92663 Moeller Instrument Company, Incorporated (714) 650-3799 4 Provided by

25、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6 b P.O. Box 668 128 Main Street Ivoryton, CT 06442 (800) 243-93 10 MILITARY INTERESTS: Custodians Navy - SH Air Force - 99 A-A-59308 9038054 0003186 TO1 A-A-593 08 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FCGC Preparing Activity: DLA - GS (Project 6605-0502) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-