ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:29.54KB ,
资源ID:687367      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-687367.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA A-A-59427-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END LARGE DOMED HEAD ALUMINUM ALLOY CARBON STEEL《碳素钢 铝合金制大球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf)为本站会员(李朗)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA A-A-59427-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END LARGE DOMED HEAD ALUMINUM ALLOY CARBON STEEL《碳素钢 铝合金制大球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf

1、AMSC N/A 1 of 4 FSC5320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-5942720 APRIL 1999COMMERCIAL ITEM DESCRIPTIONRIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL,OPEN END, LARGE DOMED HEAD, ALUMINUM ALLOY, CARBON STEELThis General Services Administrati

2、on has authorized the use of this Commercial Item Description forall Federal agencies.1. SCOPE: This Commercial Item Description (CID) covers the requirements for pull-stem expandable blindrivets. These rivets are intended for rapid and permanent non-structural fastening applications in which access

3、is available to one side only.2. SALIENT CHARACTERISTICS:2.1 Blind rivets furnished under this CID shall conform to the materials, strengths, and dimensions as specified inTable I, II, and III and as shown in Figure 1 below.FIGURE 1. RIVETSBENEFICIAL COMMENTS, RECOMMENDATIONS, ADDITIONS, DELETIONS,

4、CLARIFICATIONS,ETC., AND DATA WHICH MAY IMPROVE THIS DOCUMENT SHOULD BE SENT TO: DEFENSEINDUSTRIAL SUPPLY CENTER, ATTN: DISC-AEEB, 700 ROBBINS AVENUE, PHILADELPHIA, PA19111-5096.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594272TABLE I. MATER

5、IAL COMBINATION SYMBOLS AND STRENGTHSSYMBOL MATERIAL COMBINATION RIVETDIAMINIMUMSHEARLOADLBSMINIMUMTENSIONLOADLBSA Body: 5056 Al Alloy(UNS A95056)Mandrel: 1006-1038 Steel(UNS G10060-G10380).125.188170380220500B Body: 5052 Al Alloy(UNS A95052)Mandrel: 2024 Al Alloy(UNS A92024).125.188120260150320D Bo

6、dy: 1006-1010 Steel(UNS G10060-G10100)Mandrel: 1030-1038 Steel(UNS G10300-G10380).125.188260540310680TABLE II. BASIC DIMENSIONSBASIC DIMENSIONSNOMDIA.SIZECODENOMDIA D H ERMAXWNOMFMAXPMINRECOMMENDEDHOLE SIZE4 .125 .128.122.390.360.065.034.020 .076 L MAX+ .1201.00 .129-.1336 .188 .191.183.650.600.092.

7、067.025 .114 L MAX+.1601.00 .192-.196Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594273TABLE III. DASH NUMBERS AND DIMENSIONSDASH NUMBERA B D L RECOMMENDEDGRIP RANGEA402A404A406A408B402B404B406B408D402D404D406D408.235-.275.360-.400.485-.535.6

8、10-.670.063-.125.188-.250.313-.375.376-.500 1/A504A506A508B504B506B508D504D506D508.385-.425.510-.550.635-.695.188-.250.251-.375.376-.500A606A608A610A612B606B608B610B612D606D608D610D612.535-.575.660-.700.785-.850.910-.980.251-.375.376-.500.501-.625.626-.7501/ When applicable, supplier may provide a d

9、ash 407, with a grip range of .376-.437.2.2 Materials shall be of the type and grade specified in Table I.2.3 Surface finish.2.3.1 Carbon steel mandrels shall be zinc plated or phosphate coated.2.3.2 Aluminum alloy rivets shall be furnished either chemically treated or anodically treated at the supp

10、liersoption2.4 Workmanship. Rivets shall be of uniform quality and free from injurious seams and other injurious defects.2.5 Single shear load. The shear test shall be performed in accordance with Test Method 20 of MIL-STD-1312,or equivalent and shall conform to the data specified in Table I.2.6 Ten

11、sion load. The tension test shall be performed in accordance with Test Method 8 of MIL-STD-1312, orequivalent and shall conform to the data specified in Table I.2.7 Packaging requirements The requirements for packaging shall be in accordance with ASTM D3951.3. QUALITY ASSURANCE PROVISIONS.3.1 Produc

12、t conformance. The products provided shall meet the salient characteristics of this commercial itemdescription, conform to the producers own drawings, specifications, standards, and the quality assurance practices,and be the same product offered for sale in the commercial market. The government rese

13、rves the right to requireproof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5942744. NOTES4.1 All dimensions are in inches.4.2 The part number shall consist of the basic Commercial Item Description Number followed by a dash

14、 numberfrom Table III. The dash number consists of a material combination symbol from Table I, a nominal bodydiameter size code from Table II, and a grip range code from Table III.EXAMPLE: AA59427 B 6 06GripNominal diameterMaterialCommercial Item Description NumberAA59427B606 Indicates - Rivet, blin

15、d, nonstructural, retainedmandrel, open-end, domed head, 5052(UNS A95052) aluminum alloy body, 2024(UNS A92024) aluminum alloy mandrel;nominal body diameter size, .188;grip range, .251-.375.Military Interests:Custodians: Preparing Activity:Army - AR DLA-ISNavy - ASAir Force - 99Review Activities: (P

16、roject No. 5320-0956)Army - AV, MIAir Force - 11, 82National Security Agency-NSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3 and 8. In b

17、lock 1, both the document number and revision letter should be given.2. The submitter of this form must complete blocks 4, 5, 6 and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, or to request w

18、aivers, or clarification of requirements on current contracts.Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-594272. DOCUMENT DATE (YYMMDD)9904203. DOCUMEN

19、T TITLE:RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL, OPEN END, LARGE DOMED HEAD, ALUMINUMALLOY, CARBON STEEL4. NATURE OF CHANGE5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(

20、2) AUTOVON (If applicable)7. DATE SUBMITTED (YYMMDD)8. PREPARING ACTIVITY DLA-ISa. NAMEEmelia Altomarib. TELEPHONE (Include Area Code)(1) Commercial (215) 697-6827(2) (DSN) 442-6827c. ADDRESS (Include Zip Code)Defense Industrial Supply Center700 Robbins AvenueBldg. 3 (Code DISC-AESD)Philadelphia, PA

21、 19111-5096IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:Defense Quality and Standardization Office5203 Leesburg Pike, Suite 1403Falls Church, VA 22041TELEPHONE (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1