DLA A-A-59428-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END 100 DEG COUNTERSUNK HEAD ALUMINUM ALLOY《铝合金制100度开口端型限动芯棒用非结构性埋头盲铆钉》.pdf

1、AMSC N/A 1 of 4 FSC 5320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-5942820 APRIL 1999COMMERCIAL ITEM DESCRIPTIONRIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL,OPEN END, 100O COUNTERSUNK HEAD, ALUMINUM ALLOYThis General Services Administration has a

2、uthorized the use of this Commercial Item Description forall Federal agencies.1. SCOPE: This Commercial Item Description (CID) covers the requirements for pull-stem expandable blindrivets. These rivets are intended for rapid and permanent non-structural fastening applications in which accessis avail

3、able to one side only.2. SALIENT CHARACTERISTICS:2.1 Blind rivets furnished under this CID shall conform to the materials, strengths, and dimensions as specified inTable I, II, and III and as shown in Figure 1 below.FIGURE 1. RIVETSBENEFICIAL COMMENTS, RECOMMENDATIONS, ADDITIONS, DELETIONS, CLARIFIC

4、ATIONS,ETC., AND DATA WHICH MAY IMPROVE THIS DOCUMENT SHOULD BE SENT TO: DEFENSEINDUSTRIAL SUPPLY CENTER, ATTN: DISC-AEEB, 700 ROBBINS AVENUE, PHILADELPHIA, PA19111-5096.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594282TABLE I. MATERIAL COMB

5、INATION SYMBOLS AND STRENGTHSSYMBOL MATERIAL COMBINATION RIVETDIAMINIMUMSHEARLOADLBSMINIMUMTENSIONLOADLBSA Body: 5056 Al Alloy(UNS A95056)Mandrel: 1006-1038 Steel(UNS G10060-G10380).125 170 220B Body: 5052 Al Alloy(UNS A95052)Mandrel: 2024 Al Alloy(UNS A92024).125 120 150TABLE II. BASIC DIMENSIONSBA

6、SIC DIMENSIONSNOMDIA.SIZECODENOMDIA D HEREFRMAXWNOMFMAXPMINRECOMMENDEDHOLE SIZE4 .125 .128.122.233.207.045 .025 .076 L MAX+ .1201.00 .129-.133TABLE III. DASH NUMBERS AND DIMENSIONSDASH NUMBER LMAXRECOMMENDEDGRIP RANGEA402A403B402 .275.337.092-.125.126-.187Provided by IHSNot for ResaleNo reproduction

7、 or networking permitted without license from IHS-,-,-A-A-5942832.2 Materials shall be of the type and grade specified in Table I.2.3 Surface finish.2.3.1 Aluminum alloy rivets shall be furnished either chemically treated in accordance with MIL-C-5541, oranodically treated in accordance with MIL-A-8

8、625 at the suppliers option2.3.2 Carbon steel mandrels shall be zinc plated or phosphate coated.2.4 Workmanship. Rivets shall be of uniform quality and free from injurious seams and other injurious defects.2.5 Single shear load. The shear test shall be performed in accordance with Test Method 20 of

9、NASM1312, orequivalent and shall conform to the data specified in Table I.2.6 Tension load. The tension test shall be performed in accordance with Test Method 8 of NASM1312, orequivalent and shall conform to the data specified in Table I.2.7 Packaging requirements The requirements for packaging shal

10、l be in accordance with ASTM D3951.3. QUALITY ASSURANCE PROVISIONS.3.1 Product conformance. The products provided shall meet the salient characteristics of this commercial itemdescription, conform to the producers own drawings, specifications, standards, and the quality assurance practices,and be th

11、e same product offered for sale in the commercial market. The government reserves the right to requireproof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5942844. NOTES4.1 All dimensions are in inches.4.2 The part number sha

12、ll consist of the basic Commercial Item Description Number followed by a dash numberfrom Table III. The dash number consists of a material combination symbol from Table I, a nominal bodydiameter size code in thirty-seconds of an inch from Table II, and a maximum grip code in sixteenths of an inchfro

13、m Table III.EXAMPLE: AA59428 A 4 03Grip Range CodeNominal DiameterMaterialCommercial Item Description NumberAA59428A403 Indicates - Rivet, blind, nonstructural, retainedmandrel, open-end, 100o countersunk head,5056 (UNS A95056) aluminum alloy body,C1006-C1038 (UNS G10060-G10380) steelmandrel; nomina

14、l body diameter size, .125;grip range, .126-.187.Military Interests:Custodians: Preparing Activity:Army - AR DLA-ISNavy - ASAir Force - 99Review Activities: (Project No. 5320-0957)Army - AV, MIAir Force - 11, 82National Security Agency-NSProvided by IHSNot for ResaleNo reproduction or networking per

15、mitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3 and 8. In block 1, both the document number and revision letter should be given.2. The submitter of this form must complete blocks 4, 5, 6 and 7.3. The

16、preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, or to request waivers, or clarification of requirements on current contracts.Comments submitted on this form do not constitute or imply authorization to wai

17、ve any portion of the referenced document(s) or to amend contractual.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-594282. DOCUMENT DATE (YYMMDD)9904203. DOCUMENT TITLE:RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL, OPEN END, 100O COUNTERSUNK HEAD, ALUMINUMALLOY4. NATURE OF CHANGE5. REASON FOR RECOMM

18、ENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) AUTOVON (If applicable)7. DATE SUBMITTED (YYMMDD)8. PREPARING ACTIVITY DLA-ISa. NAMEEmelia Altomarib. TELEPHONE (Include Area Code)(1) Commercial (

19、215) 697-6827(2) (DSN) 442-6827c. ADDRESS (Include Zip Code)Defense Industrial Supply Center700 Robbins AvenueBldg. 3 (Code DISC-AESD)Philadelphia, PA 19111-5096IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:Defense Quality and Standardization Office5203 Leesburg Pike, Suite 1403Falls Church, VA 22041TELEPHONE (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-