DLA A-A-59432-1999 PLUGS PIPE MAGNETIC HEADLESS IRON STEEL OR ALUMINUM ALLOY [Superseded DLA MIL-P-54001 A CANC NOTICE 1 DLA MIL-P-54001 A DLA MIL-P-54001 DLA MS49006 REV C CANC NO.pdf

1、I INCH-POUND I A-A-59432 21 May 1999 SUPERSEDING 9 March 1973 MS49006C 15 November 1972 M IL-P-54001 A COMMERCIAL ITEM DESCRIPTION PLUGS, PIPE, MAGNETIC, HEADLESS: IRON, STEEL OR ALUMINUM ALLOY The General Services Administration has authorized the use of this Commercial Item Description (CID) for a

2、ll federal agencies. 1. SCOPE. This CID covers: (1) headless magnetic pipe plugs having recessed hex heads, up to one inch size, conforming to Society of Automotive Engineers (SAE) Standard J531, and (2) headless magnetic pipe plugs having recessed square heads, for sizes over one inch, conforming t

3、o American Society of Mechanical Engineers (ASME) Standard B16.14. These magnetic pipe plugs are intended for use in automotive engine oil systems, transmissions, gear boxes, and circulating oil systems, and other systems of circulating fluids in which ferrous metal particles and/or chips 2. CLASSIF

4、ICATION a. Type b. Type nay be present. Magnetic plugs shall be of the following types: - Aluminum Alloy. I - Malleable Iron, Cast Iron, or Cold Finished Steel. 3. SALIENT CHARACTERISTICS. 3.1 Desian and Fabrication. Casting, forging, or machining may be used to fabricate the magnetic pipe plugs. Th

5、e plug design requirements for dimensions and tolerances, pipe thread size, and magnetic lift shall be in accordance with Figure 1 and Table I. The aluminum alloy plugs shall be anodized, in accordance with the contract or order. The ferrous plugs shall have a plain, uncoated finish, or other finish

6、 in accordance with the contract or order. 3.2 Material. The material for aluminum alloy plugs shall be in accordance with QQ-A-225/1, QQ-A- 225/3, QQ-A-225/6, QQ-A-225/8 or QQ-A-367. The material for malleable iron plugs shall be in accordance with ASTM-A-47. The material for cast iron plugs shall

7、be in accordance with ASTM A48. The material for cold finish steel plugs shall be in accordance with ASTM A 148. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any other data which may improve this document should be sent to: Defense Supply Center Columbus, ATT

8、N: DSCC-VAI, 3990 East Broad Street, Columbus, Ohio 4321 6-5000. FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59432 3.3 Maanet. The magnet shall be a permanent magnet in accordance with Magnetic Materials Producers Association (MMPA)

9、Standard 0100. The magnet lift rating is defined as the weight of soft steel having one smooth side, that the magnet will retain after contact has been established, and for at least 48 hours after magnetization. The magnet shall be attached to the plug in such a manner as to require physical displac

10、ement of metal before the magnet can be removed. The maximum diameter of the magnet shall be at least 0.100 inch smaller than the pitch diameter of the plug thread. 3.4 Threads. The threads shall be NPTF for plugs up to and including the three (3) inch size and NPT for the four (4) inch size. 3.5 To

11、xic Chemicals/Hazardous Substances. The use of toxic chemicals, hazardous substances, or ozone depleting chemicals (ODC) will be avoided, when feasible. 4. REGULATORY REQUIREMENTS. 4.1 Recvcled/Recovered Materials. The offerer/contractor is encouraged to use recovered materials to the maximum extent

12、 practical, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product Conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specificatio

13、ns, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Market AcceDtance. The producer shall meet the following market acceptance criteria. 5.2.1 The producer produ

14、cing the item must have been producing similar commercial grade items meeting the requirements of this CID for at least two (2) years. 5.2.2 The producer must have sold one hundred (100) similar commercial units that meet or exceed the requirements of this CID over the past two (2) years. 6. PACKAGI

15、NG. 6.1 Preservation, Packina, and Markinq. Preservation, packing, and marking shall be specified in the contract or order. 7. NOTES. 7.1 Part Identification Number (PIN). The PIN shall be used for Government purposes to buy commercial products described by this CID. The following part identificatio

16、n numbering procedure is for government purposes and does not constitute a requirement for the contractor. PIN Construction I CID Number I Dash Number (from Table 1) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A- A-59432 DASH NUMBERS TYPE I TYP

17、E II o1 02 03 04 05 06 I NOMINAL A3 B3 c3 LIFP HEAD STYLE SIZE- NPTF MIN. MAX. MIN. MAX. MAX. MIN. (RECESSED) 0.125-27 0.290 0.310 0.188 0.193 0.375 40Z HEX SOCKET 0.250 - 18 0.445 0.475 0.250 0.255 0.375 4 OZ HEX SOCKET 0.375 - 18 0.445 0.475 0.313 0.318 0.375 4 OZ HEX SOCKET -7- , + ;p - - I 22 I

18、3.000 - 8 I 1.130 I - I 1.391 I 1.410 I 0.625 I 10 OZ I SQUARE SOCKET - I See Table 1 For Dimensions 4 Taper Max AM98-057-00-AO (MP5400 Plug) Figure 1. Pipe pluqs, maqnetic - headless. Table I. Pipe pluqs, maqnetic - headless. NOTES: 1. 2. 3. 4. Materials. Type I, Aluminum Alloy, or Type II, Malleab

19、le Iron, Cast Iron, or Cold Finished Steel. Threads. Threads shall be NPTF for plugs up to and including the 3-inch size and NPT for the 4-inch size. Dimensions and Tolerances. All dimensions are in inches. Figure I and this table are for identification purposes only and are not intended to restrict

20、 designs or shapes of plugs not dimensioned herein. Dimensions and tolerances not shown shall be in accordance with SAE J531 for sizes up to and including one (1) inch and in accordance with ASME B16.14 for sizes greater than one (1) inch. Maqnetic Lift Ratinq. The magnetic lift rating is defined as

21、 the weight of soft steel, having one smooth side, that the magnet will retain after contact has been established, and for at least forty-eight (48) hours after magnetization. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59432 7.2 Orderina D

22、ata. The contract or order should specify the following: a. b. C. Quality assurance provisions. d. Packaging requirements. CID number, revision, and PIN. Type of metal and finish on the plug. 7.3 National Stock Numbers (NSNs). The following is a list of identified NSNs assigned that correspond to th

23、is CID. Procurement “ SDecification Detail Sheet PIN New CID PIN 4730-00-045-9764 MIL- P-5400 1 MS49006-1 AA59432-01 4730-01 -1 13-2353 MIL- P-5400 1 MS49006-2 AA59432-02 4730-00-045-9767 MIL- P-5400 1 MS49006-4 AA59432-04 4730-01 -307-01 39 MIL- P-5400 1 MS49006-4 AA59432-04 4730-00-045-9768 MIL- P

24、-5400 1 MS49006-5 AA59432-05 4730-00-045-9769 MIL- P-5400 1 MS49006-6 AA59432-06 4730-00-045-9771 MIL- P-5400 1 NONE AA59432-08 4730-01 -1 35-831 O MIL- P-5400 1 MS49006-8 AA59432-08 4730-00-968-61 29 MIL- P-5400 1 MS49006-1 O AA59432-1 O 4730-01 -281 -9381 MIL- P-5400 1 MS49006-11 AA59432-11 4730-0

25、0-045-9833 MIL- P-5400 1 MS49006-12 AA59432-12 4730-00-045-9835 MIL- P-5400 1 MS49006-14 AA59432-14 4730-00-045-9837 MIL- P-5400 1 MS49006-18 AA59432-18 7.4 Sources of Suly. The following is a list of suppliers that have provided magnetic pipe plugs meeting the requirements of this CID to the Govern

26、ment in the past. This is not intended to be an all-inclusive list and should not be used to restrict procurement from other qualified vendors. CAGE 02951 03958 OKRH6 ORVB7 OTMN8 OU3H4 1 X015 36540 571 40 59680 62727 66200 6W912 7H072 9R205 COMPANY NAME Pittsburgh Plug and Products Corp Mindeco Corp

27、oration Piping Components, Inc. Westwater Supply - Springfield, Inc. M G Industries, Inc. J and B Owl Technologies, Inc. Nestor Sale, Inc. Lisle Corporation Salem Mfg. and Sales, Inc. B and E Manufacturing Company Mid-State Sales, Inc. Pioneer Valve and Fitting Co., Inc. MEG Technologies, Inc. Napco

28、 International, Inc. Arlo Corporation LOCATION Evans City, PA 16033-921 2 Oceanside, NY 11572 Melvindale, MI 48122 Springfield, OH 45501-1 145 Camden, NJ 08103 Mount Vernon, NY 10550 Largo, FL 34647 Clarinda, IA 51 632-2342 Columbus, OH 43232-3846 Stanton, CA 90680 Columbus, OH 43230-6600 Brooklyn,

29、NY 1 1206-3299 Long Beach, CA 90804 Hopkins, MN 55343-7464 Caldwell, NJ 07007 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59432 8. SOURCE OF DOCUMENTS. 8.1 The Federal Acquisition Regulation (FAR) 23.403 and Federal Standards Documents, US

30、Government Printing Office, Washington, DC 20402. 8.2 SAE standards are available from the Society of Automotive Engineers Inc., 400 Commonwealth Drive, Warrendale, PA 15096. 8.3 ASME standards are available from the American Society of Mechanical Engineers, 345 East 47 Street, New York, NY 10017. 8

31、.4 MMPA standards are available from the Magnetic Materials Producers Association, 8 South Michigan Avenue, Chicago, IL 60603. 8.5 ASTM standards are available from the American Society for Testing and Materials, 1 O0 Barr Harbor Drive, West Conshohocken, PA 19428. MILITARY INTEREST: Custodians: Army - AR Air Force - 99 Navy - YD2 DLA-CC Review activities: Army - AV Navy - MC CIVIL AGENCY COORDINATION ACTIVITY: GSA - FSS Preparing activity: DLA - CC (Project 4730-0728-02) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-