DLA A-A-59434-1999 TANK TESTING TIRE AND TUBE《装轮胎和小软管的测试罐》.pdf

1、A-A-594347 May 1999SUPERSEDINGMIL-T-14608G22 June 1992COMMERCIAL ITEM DESCRIPTIONTANK, TESTING, TIRE AND TUBEThe General Services Administration has authorized the use of this Commercial ItemDescription (CID) for all federal agencies.1. SCOPE. This CID covers one type of tire and tube testing tank t

2、o be used for detecting and locatingair leaks in inner tubes and mounted tubeless tires; and for testing for air leaks in valve stems and valvecovers.2. CLASSIFICATION. The tanks shall be available in the following sizes:a. Size 1 - this testing tank shall have the capacity to completely submerge in

3、flated innertubes and mounted tubeless tires up to, and including, 12.00 inch thread width by 24 inchwheel size. The tank shall have a minimum inside diameter of fifty-two (52) inches and aminimum depth of seventeen and one-half (17 ) inches.b. Size 2 - this testing tank shall have the capacity to c

4、ompletely submerge inflated innertubes and mounted tubeless tires up to, and including, 18.00 inch thread width by 24 inchwheel size. The tank shall have a minimum inside diameter of seventy-two (72) inchesand a minimum depth of thirty (30) inches.3. SALIENT CHARACTERISTICS.3.1 Design and Fabricatio

5、n. The tank shall be fabricated from a material thick enough to preclude anydeformation caused by the liquid and loads imposed during testing, and may be reinforced throughout withcorrosion resistant reinforcing. The tank shall be leak-proof when filled to the top with liquid. A drain plugor valve s

6、hall be provided to allow the tank to completely drain while the tank is in an installed position.The tank shall be capable of supporting the tube-submerging mechanism.3.2 Tube-Submerging Unit. The tank shall have a tube-submerging unit (spider) which is attached to thetank. The spider shall allow f

7、or the visual inspection of the submerged tire or tube and may be operatedby an air cylinder unit, which is used to raise and lower the spider. The spider shall be attached to the airBeneficial comments, recommendations, additions, deletions, clarifications, etc., and any otherdata which may improve

8、 this document should be sent to: Defense Supply Center Columbus,ATTN: DSCC-VAI, 3990 East Broad Street, Columbus, Ohio 43216-5000.FSC 4910INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594342cylinder unit in a manner to permit the rot

9、ation of the submerged tire or tube. The distance (clearance)between the spider in the raised position and the top of the tank shall be large enough to permitunrestricted loading of the specified inflated tire and inner tube sizes. The spider shall be designed so thatit will not damage the tires or

10、tubes being tested.3.3 Air Cylinder Unit. The air cylinder unit shall operate within an air line pressure ranging from 100pounds per square inch gage (psig) to 175 psig. The cylinder shall be capable of withstanding an air linepressure of 200 psig for a period of two (2) minutes without damage or le

11、akage. The cylinder may besingle or double acting. If single acting, the cylinder shall be provided with two coil extension springs orother device to act as retrievers, and shall be controlled by a two-way air valve, or an intake valve and anexhaust valve, or other mechanism. If a double acting cyli

12、nder is used, a three-way valve or othermechanism shall be provided to control the cylinder, to provide for extension, retraction, or hold thecylinder in an intermediate position.3.3.1 Air Valve. The valve operating mechanism shall be mounted in an accessible position for handoperation without the u

13、se of tools and shall control the airflow in the cylinder. The air valve and cylinderunit shall be capable holding the spider and the tire or tube under test at any required depth, with amaximum allowable rise of one-half (1/2) inch during a twenty (20) minute period.3.4 Fastening Devices. Screws, p

14、ins, bolts, and similar parts shall be installed with means for adjustmentand for preventing loss of tightness. The methods for adjustment and for preventing loss of tightness shallbe in accordance with accepted engineering standards and practices.3.5 Accessory Support Stand. When specified, the siz

15、e 1 tank shall be provided with a support stand.The stand may be either a structural part of the tank or a separate holding, support, stand. The standshall be constructed of not less than four (4) legs, or other adequate means, to maintain the tank in astable position during testing operations. The

16、stand shall position the tank at a height of thirty-six (36),+ six (6), inches when measured from the tank top to the floor level. The stand shall be capable ofsupporting the fully loaded tank without deformation or damage.3.6 Toxic Chemicals/Hazardous Substances. The use of toxic chemicals, hazardo

17、us substances, orozone depleting chemicals (ODC) will be avoided, when feasible.4. REGULATORY REQUIREMENTS.4.1 Recycled/Recovered Materials. The offerer/contractor is encouraged to use recovered materials tothe maximum extent practical, in accordance with paragraph 23.403 of the Federal Acquisition

18、Regulation(FAR).5. QUALITY ASSURANCE PROVISIONS.5.1 Product Conformance. The contractor shall certify and maintain substantiating evidence that theproduct offered meets the salient characteristics of this CID, and that the product conforms to theproducers own drawings, specifications, standards, and

19、 quality assurance practices, and is the sameproduct offered for sale in the commercial market. The Government reserves the right to require proof ofsuch conformance prior to first delivery and thereafter as may be otherwise provided for under provisionsof the contract.5.2 Market Acceptance. The fol

20、lowing market acceptance criteria are necessary to document the qualityof the product to be provided under this CID.5.2.1 The producer/provider shall have demonstrated the capability to produce and/or provide similarcommercial grade items that meet or exceed the requirements of this CID within the p

21、ast five (5) years.5.2.2 The producer/provider must adhere to the product conformance requirements above.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5943436. PACKAGING.6.1 Preservation, Packing, and Marking. Preservation, packing, and marking

22、 shall be specified in thecontract or order.7. NOTES.7.1 Part Identification Number (PIN). The PIN shall be used for Government purposes to buy commercialproducts described by this CID. The following part identification numbering procedure is for governmentpurposes and does not constitute a requirem

23、ent for the contractor.PIN ConstructionAA59434 XXCID Number + Dash Number(01 - for size 1 (small) tank)(02 - for size 2 (large) tank)7.2 Ordering Data. The contract or order should specify the following:a. CID number, revision, and PIN.b. Requirement for support stand, size 1 tank only.c. Quality as

24、surance provisions.d. Packaging requirements.7.3 National Stock Numbers (NSNs). The following is a list of the identified NSNs assigned thatcorrespond to this CID.NSN Old PIN New CID PIN4910-00-190-5235 MILT14608 SIZE 1 AA59434-014910-00-330-5441 MILT14608 SIZE 2 AA59434-027.4 Sources of Supply. The

25、 following is a list of suppliers that have provided testing tanks meeting therequirements of this CID to the Government in the past. This is not intended to be an all-inclusive list noran endorsement of any of the listed suppliers and should not be used to restrict procurement from otherqualified v

26、endors.CAGE COMPANY NAME LOCATION0P568 Allied Metal Products and Indianapolis, IN 46225-181654267 Orlotronics Corporation Bridgeport, PA 19405-181583790 Randall Manufacturing Co., Inc. Hillside, NJ 07205-11078B805 Eur-Pac Corporation Brooklyn, NY 11222-373298897 Lockheed Martin Corporation Marietta,

27、 GA 30063Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5943448. SOURCE OF DOCUMENTS.8.1 The Federal Acquisition Regulation (FAR) 23.403 may be obtained from the Superintendent ofDocuments, US Government Printing Office, Washington, DC 20402.MILITARY INTEREST: CIVIL AGENCY COORDINATION ACTIVITY:Custodians: GSA-FSSArmy - ALAir Force - 99 Preparing activity:DLA - CC DLA - CCReview activities:Army CR4 (Project 4910-0840-01)Air Force - 82Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-