DLA A-A-59440 1 B-2012 COCK-VALVE CENTER DRAIN INTERNAL SEAT OR EXTERNAL SEAT 150 PSI BRASS NON-FLAMMABLE LIQUID OR GAS NPTF-1 THREADS.pdf

1、AMSC N/A FSC 4820 A-A-59440/1B 21 May 2012 SUPERSEDING A-A-59440/1A 23 May 2005 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET COCK-VALVE, CENTER DRAIN, INTERNAL SEAT OR EXTERNAL SEAT, 150 PSI, BRASS, NON-FLAMMABLE LIQUID OR GAS, NPTF-1 THREADS The General Services Administration has authorized the

2、 use of this commercial item description for all federal agencies. The complete requirements for procuring the cock-valve, center drain, internal seat or external seat, 150 psi, brass, non-flammable liquid or gas, NPTF-1 threads described herein shall consist of this document and the issue in effect

3、 of A-A-59440. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). SALIENT CHARACTERISTICS. Interface and physical dimensions. Cock-valv

4、es, center drain, internal seat or external seat, 150 psi, brass, non-flammable liquid or gas, NPTF-1 threads supplied to this CID specification sheet shall be as specified herein (see figure 1 and figure 2). Sizes. Nominal sizes of 1/4 inch through 1 inch with NPTF-1 threads are covered by this CID

5、. Intended applications. These items are for use in non-flammable liquid or gas systems where pressures do not exceed 150 psig (10.3 bar) at 150F (65.6C) and the liquid or gas is compatible with brass. Permissible variations in dimensions. Figures 1 and 2 lists the permissible variation in dimension

6、s for each size. The external dimensions of the cock-valve should not limit procurement unless the end item applications restrict these dimensions. Optional designs. Figures 1 and 2 are for identification purposes only and are not intended to restrict designs or shapes not dimensioned. Valve bodies.

7、 Valve bodies shall be provided with hexagonal wrenching surfaces. INCH-POUND AA59440 /01 - 001 Blank or C I I I I _I_ _I_ _I_ _I_ CID number Applicable Dash number Handle plating CID spec sheet (see figure 1 (see figure 1) (two digits) and figure 2) and figure 2) Provided by IHSNot for ResaleNo rep

8、roduction or networking permitted without license from IHS-,-,-A-A-59440/1B 2 Threads. Threads are dryseal NPTF-1 in accordance with A-A-59440. Material. Brass. Body and handle, external seat only, shall be brass in accordance with the following commercial standards: ASTM B16/B16M ASTM B121/B121M AS

9、TM B505/B505M SAE AMS4845 ASTM B22 ASTM B124/B124M ASTM B584 SAE AMS4855 ASTM B30 ASTM B148 ASTM B763 SAE AMS4860 ASTM B36/B36M ASTM B176 ASTM B770 SAE AMS4862 ASTM B61 ASTM B271 SAE AMS4890 ASTM B62 ASTM B369 Carbon steel. Cast, forged, or machined carbon steel shall be in accordance with QQ-S-698.

10、 Handle internal seat (see figure 1). Handle may be brass, hot rolled or cold rolled steel conforming to QQ-S-698 or another commonly accepted industry standard. Handle external seat (see figure 2). Handle may be hot rolled or cold rolled steel conforming to QQ-S-698 or another commonly accepted ind

11、ustry standard. Protective coating: a. Brass: None. b. Carbon steel: (1) Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 2. (2) Zinc in accordance with ASTM B633, type II, 12.7 m (50 microinches) minimum. Caution: Cadmium shall not be used in potable water or oxygen systems. Brass shall

12、not have any lead contents. Test pressures: a. Shell: 150 psig (10.3 bar). b. Seat: 50 psig (3.45 bar). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/1B 3 Dash number Handle plating A Pipe Thread NPTF-1 B maximum (mm) C open maximum (mm)

13、D diameter minimum (mm) E diameter minimum (mm) F .015 (0.38 mm) 001 Zinc or Brass 1/8-27 1.38 (34.0) 1.88 (47.8) .19 (4.8) .12 (3.1) .44 or .56 (11.2 or 14.2) 001B Brass 001C Cadmium 001Z Zinc 002 Zinc or Brass 1/4-18 .50 (38.1) 2.00 (50.8) .19 (4.8) .19 (4.8) .56 or .62 (14.2 or 15.7) 002B Brass 0

14、02C Cadmium 002Z Zinc 003 Zinc or Brass 3/8-18 1.50 (38.1) 2.00 (50.8) .31 .02 (7.6 0.5) .25 to .31 (6.4 to7.9) .69 or .75 (17.5 or 19.1) 003B Brass 003C Cadmium 003Z Zinc NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified toleranc

15、es are .010 inch (0.25 mm). 4. Diameter of hole shall be adequate to allow drainage through the valve. FIGURE 1. Dimensions and configuration internal seat. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/1B 4 Dash number Handle plating A P

16、ipe Thread NPTF-1 B maximum (mm) C closed reference (mm) D diameter reference (mm) E diameter minimum (mm) F .015 (0.38 mm) 004 Zinc or Brass 1/8-27 1.31 (33.3) .90 (22.86) .09 (2.3) .12 (3.0) .44 or .50 (11.2 or 12.7) 004B Brass 004C Cadmium 004Z Zinc 005 Zinc or Brass 1/4-18 1.38 (35.1) 1.00 (25.4

17、) .16 (4.1) .19 (4.8) .50 or .56 (12.7 or 14.2) 005B Brass 005C Cadmium 005Z Zinc 006 Zinc or Brass 3/8-18 1.6 (42.93) 1.44 (36.6) .16 (4.1) .19 (4.8) .62 or .69 (15.7 or 17.5) 006B Brass 006C Cadmium 006Z Zinc 007 Zinc or Brass 1/2-14 2.00 (50.8) 1.62 (41.1) .31 (7.9) .38 (9.7) .81 or .88 (20.6 or

18、22.4) 007B Brass 007C Cadmium 007Z Zinc 008 Zinc or Brass 1-11 1/2 2.50 (63.5) 2.31 (58.7) .53 (13.5) .75 (19.1) 1.38 or 1.50 (35.1 or 38.1) 008B Brass 008C Cadmium 008Z Zinc NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified toler

19、ances are .010 inch (0.25 mm). 4. Dimension “C” open/closed length dimensions may vary from manufacturer to manufacturer. 5. Diameter of hole shall be adequate to allow drainage through the valve. FIGURE 2. Dimensions and configuration external seat. Provided by IHSNot for ResaleNo reproduction or n

20、etworking permitted without license from IHS-,-,-A-A-59440/1B 5 NOTES: PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. FEDERAL SPECIFICATION QQ-S-698 - Steel, S

21、heet and Strip, Low Carbon COMMERCIAL ITEM DESCRIPTION A-A-59440 - Cock-Valves and Valves, General Requirements for (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphi

22、a, PA 19111-5094.) Other Publications ASTM INTERNATIONAL ASTM B16/B16M - Free-Cutting Brass Rod, Bar and Shapes for use in Screw Machines ASTM B22 - Bronze Castings for Bridges and Turntables ASTM B30 - Copper Alloys in Ingot Form ASTM B36/B36M - Brass Plate, Sheet, Strip, and Rolled Bar ASTM B61 -

23、Steam or Valve Bronze Castings ASTM B62 - Composition Bronze or Ounce Metal Castings ASTM B121/B121M - Leaded Brass Plate, Sheet, Strip, and Rolled Bar ASTM B124/B124M - Copper and Copper Alloy Forging Rod, Bar, and Shapes ASTM B148 - Aluminum-Bronze Sand Castings ASTM B176 - Copper-Alloy Die Castin

24、gs ASTM B271 - Copper-Base Alloy Centrifugal Castings ASTM B369 - Copper-Nickel Alloy Castings ASTM B505/B505M - Copper Alloy Continuous Castings ASTM B584 - Copper Alloy Sand Castings for General Applications ASTM B633 - Electrodeposited Coatings of Zinc on Iron and Steel ASTM B763 - Copper Alloy S

25、and Castings for Valve Applications ASTM B770 - Copper-Beryllium Alloy Sand Castings for General Applications (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Provided by IHS

26、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/1B 6 SAE INTERNATIONAL SAE-AMS-QQ-P-416 - Plating, Cadmium (Electrodeposited) SAE AMS4845 - Tin Bronze Castings, Sand and Centrifugal 87.5CU - 10SN - 2ZN as Cast SAE AMS4855 - Leaded Red Brass, Sand and Cent

27、rifugal Castings 85CU - 5.0SN - 5.0PB - 5.0ZN as Cast SAE AMS4860 - Manganese Bronze, Sand and Centrifugal Castings 58CU - 39ZN - 1.2FE - 1.0AL - 0.80MN as Cast SAE AMS4862 - Manganese Bronze, Sand and Centrifugal Castings 63CU - 24ZN - 6.2AL - 3.8MN - 3.0FE High Strength, as Cast SAE AMS4890 - Copp

28、er-Beryllium Alloy Castings 97CU - 2.1BE - 0.52CO - 0.28SI Solution Heat Treated (TBOO) (Copies of these documents are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 inside USA and Canada or 724-776-4970 outside USA,

29、email at CustomerServicesae.org.) Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers we

30、re known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and address 01276 Eaton

31、 Aeroquip Inc. 14615 Lone Oak Rd. Eden Prairie, MN 55344 952-294-2032/888-258-0222 93061 Parker-Hannifin Corp Brass Products Division 300 Parker Drive Otsego, MI 49708-1472 260-636-2104 dwsandersP 20969 Essex Brass Corp 23500 Pinewood Warren, MI 48091-3122 586-757-8200 Provided by IHSNot for Resal

32、eNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/1B 7 Military standard (MS) supersession data. This CID replaces the following MS as shown in table I. TABLE I. MS supersession data. CID PIN 1/ Superseded MS AA59440/1-001 MS35782-1 AA59440/1-001B MS35782-1 AA59440/1-00

33、1C MS35782-1 AA59440/1-001Z MS35782-1 AA59440/1-002 MS35782-2 AA59440/1-002B MS35782-2 AA59440/1-002C MS35782-2 AA59440/1-002Z MS35782-2 AA59440/1-003 MS35782-3 AA59440/1-003B MS35782-3 AA59440/1-003C MS35782-3 AA59440/1-003Z MS35782-3 AA59440/1-004 MS35782-4 AA59440/1-004B MS35782-4 AA59440/1-004C

34、MS35782-4 AA59440/1-004Z MS35782-4 AA59440/1-005 MS35782-5 AA59440/1-005B MS35782-5 AA59440/1-005C MS35782-5 AA59440/1-005Z MS35782-5 AA59440/1-006 MS35782-6 AA59440/1-006B MS35782-6 AA59440/1-006C MS35782-6 AA59440/1-006Z MS35782-6 AA59440/1-007 MS35782-7 AA59440/1-007B MS35782-7 AA59440/1-007C MS3

35、5782-7 AA59440/1-007Z MS35782-7 AA59440/1-008 MS35782-8 AA59440/1-008B MS35782-8 AA59440/1-008C MS35782-8 AA59440/1-008Z MS35782-8 1/ These parts were originally listed in MS35782 as a single part type. Due to special handling/disposal and corrosion resistance requirements the parts have been separa

36、ted in this CID. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/1B 8 Part number P/N supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown in table II. This information is being provided to assist

37、 in reducing proliferation in the Government inventory system. TABLE II. P/N Supersession data. 1/ Dash number (see figure 1 and figure 2) AA59440/1 MFRs CAGE 2/ MFRs P/N MFRs CAGE MFRs P/N MFRs CAGE MFRs P/N 001 01276 130 20969 DC100 1/8 93061 DC603-2 001C 002 01276 140 20969 DC100 1/4 93061 DC603-

38、4 002C 003 01276 230 N/A 93061 DC603-6 003C N/A 004 01276 135 N/A 93061 DC604-2 004C N/A 005 01276 145 N/A 93061 DC604-4 005C N/A 006 01276 270 N/A 93061 DC604-6 006C N/A 007 01276 108 N/A 93061 N/A 007C N/A N/A 008 01276 N/A N/A 93061 N/A 008C N/A N/A N/A 1/ The manufacturers P/N shall not be used

39、for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see marking paragraph of A-A-59440.

40、2/ Manufacturers products not approved for steam service National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID specification sheet. The list in table III is for information only and may not be indicative of all possible NSNs associated with the CID specif

41、ication sheet. For up to date information on assigned NSNs, please contact the aforementioned DLA Land and Maritime office listed in A-A-59440. TABLE III. NSNs. Dash number (see figure 1 and figure 2) AA59440/1 NSN 003 4820-00-174-0339 004 4820-00-752-9040 005 4820-00-849-1220 Provided by IHSNot for

42、 ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/1B 9 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS CIVIL AGENCIES A

43、ND COORDINATING ACTIVITIES: Custodians: GSA FSS Army AR Navy - SH Preparing activity: Air Force 99 DLA CC DLA - CC Review activities: Army - AT, AV, CR4, GL, MI Navy AS, MC, SA Air Force 71 (Project 4820-2011-031) NOTE: The activities listed above were interested in this document as of the date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-