DLA A-A-59444 A-2013 REDUCER COUPLING TUBE MALE TO FEMALE SOLDER-JOINT REFRIGERATION.pdf

1、 COMMERCIAL ITEM DESCRIPTION REDUCER COUPLING, TUBE, MALE TO FEMALE SOLDER-JOINT, REFRIGERATION The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements fo

2、r wrought copper and copper alloy solder joint pressure fittings for use with copper water tubes in refrigeration systems. 2. CLASSIFICATION/PART OR IDENTIFCATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7.1) AA59444 - 1

3、CID number Dash number 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Fittings supplied to this CID shall be as specified herein (see figure 1). 3.2 Material and finish. Fitting material and finishes shall be copper and copper alloy, as specified in ASME B16.22. 3.3 Design, const

4、ruction, and performance. Fitting design, construction, and performance shall be in accordance with ASME B16.22. 3.4 Marking. Connectors supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3

5、.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous

6、 life cycle costs. AMSC N/A FSC 4730 INCH-POUND A-A-59444A 6 August 2013 SUPERSEDING A-A-59444 22 June 1999 Comments, suggestions, or questions on this document should be addressed to: DLA Land and Maritime, Attn: VAI, P.O. Box 3990, Columbus, Ohio, 43218-3990 or emailed to FluidFlowdla.mil. Since c

7、ontact information can change, you may want to verify the currency of this address information using ASSIST Online Database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59444A 2 3.6 Workmanship. Connectors shall be pr

8、ocessed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of

9、the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product o

10、ffered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance. 6 PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial p

11、roducts to this CID. See section 2 for PIN example. The PIN procedure is for government purposes and does not constitute a requirement for the contractor. Figure 1,and table 1 are provided for configuration identification. SIZE FSIZE AFIGURE 1. Reducer coupling, male to female. Provided by IHSNot fo

12、r ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59444A 3 TABLE I. Dash numbers. Dash numbers Reducing coupling (figure 1) Tube size, Inches F x A -1 3/8 x 1/4 -2 1/2x 1/4 -3 1/2 x 3/8 -4 5/8 x 3/8 -5 5/8 x 1/2 -6 3/4 x 1/2 -7 3/4 x 5/8 -8 7/8 x 3/8 -9 7/8 x 1/2 -10 7

13、/8 x 5/8 -11 7/8 x 3/4 -12 1 1/8 x 1/2 -13 1 1/8 x 5/8 -14 1 1/8 x 7/8 -15 1 3/8 x 5/8 -16 1 3/8 x 7/8 -17 1 3/8 x 1 1/8 The PIN consists of the document identifier and a dash no. (see table I). The dash number denotes size in increments of 1/8 inch. PIN example AA59444-1: AA59444 - 1 Dash no. (see

14、table I) Document identifier 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing eff

15、orts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials on the list should be min

16、imized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these fuse plugs to DLA Land and Maritime under the Military Parts Control Advisory Group (MPCAG

17、) evaluation program, CAGE code 58536 should be used. 7.4 Sources of documents. FEDERAL REGULATIONS FAR Federal Acquisitions Regulations (FAR) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59444A 4 (Copies of this document are available online

18、at http:/www.acquisition.gov/comp/far/index.html from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401-0001.) Other Publications ASME INTERNATIONAL ASME B16.22 Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings (Copies of these documents are availa

19、ble online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.) 7.5 Ordering data. The contractor order should specify the following: a. CID document number, revision and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Cross re

20、ference data. See table II for PIN cross reference data. TABLE II. Cross reference data. MS35920 Tube size, inches AA59444 MS35920-1 3/8 x 1/4 AA59444-1 MS35920-2 1/2 x 1/4 AA59444-2 MS35920-3 1/2 x 3/8 AA59444-3 MS35920-4 5/8 x 3/8 AA59444-4 MS35920-5 5/8 x 1/2 AA59444-5 MS35920-6 3/4 x 1/2 AA59444

21、-6 MS35920-7 3/4 x 5/8 AA59444-7 MS35920-8 7/8 x 3/8 AA59444-8 MS35920-9 7/8 x 1/2 AA59444-9 MS35920-10 7/8 x 5/8 AA59444-10 MS35920-11 7/8 x 3/4 AA59444-11 MS35920-12 1 1/8 x 1/2 AA59444-12 MS35920-13 1 1/8 x 5/8 AA59444-13 MS35920-14 1 1/8 x 7/8 AA59444-14 MS35920-15 1 3/8 x 5/8 AA59444-15 MS35920

22、-16 1 3/8 x 7/8 AA59444-16 MS35920-17 1 3/8 x 1 1/8 AA59444-17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59444A 5 7.7 National Stock Numbers (NSNs). The following is a list of identified NSNs assigned that correspond to this CID. This list

23、may not be indicative of all possible NSNs associated with this CID (see table III). TABLE III. NSNs. NSN Size 4730-00-103-1863 -5 4730-00-277-7541 -10 4730-00-808-7875 -14 4730-00-808-7878 -9 4730-00-808-7879 -2 4730-00-932-0969 -1 4730-00-932-0970 -3 4730-00-972-7801 -4 7.8 Changes from previous i

24、ssue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Custodians: Preparing activity: Army - GL DLA - CC Navy SH Air Force - 99 DLA - CC (Project

25、 4730-2013-054) Review activities: Army - CE Navy - MC NOTE: The activities listed above were interested in this document as the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-