DLA A-A-59446 A-2013 ELBOW TUBE 90 DEGREE REDUCING SOLDER-JOINT REFRIGERATION.pdf

1、 COMMERCIAL ITEM DESCRIPTION ELBOW, TUBE, 90 DEGREE, REDUCING, SOLDER-JOINT, REFRIGERATION The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for wro

2、ught copper and copper alloy solder joint pressure fittings for use with copper water tubes in refrigeration systems. 2. CLASSIFICATION/PART OR IDENTIFCATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7.1) AA59446 - 32 CID

3、number Dash number 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Fittings supplied to this CID shall be as specified herein (see figure 1). 3.2 Material and finish. Fitting material and finishes shall be copper and copper alloy, as specified in ASME B16.22. 3.3 Design, construct

4、ion, and performance. Fitting design, construction, and performance shall be in accordance with ASME B16.22. 3.4 Marking. Connectors supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.5 R

5、ecycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous lif

6、e cycle costs. AMSC N/A FSC 4730 INCH-POUND A-A-59446A 6 August 2013 SUPERSEDING A-A-59446 22 June 1999 Comments, suggestions, or questions on this document should be addressed to: DLA Land and Maritime, Attn: VAI, P.O. Box 3990, Columbus, Ohio, 43218-3990 or emailed to FluidFlowdla.mil. Since conta

7、ct information can change, you may want to verify the currency of this address information using ASSIST Online Database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59446A 2 3.6 Workmanship. Connectors shall be proces

8、sed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the

9、Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offer

10、ed for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance. 6 PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial produ

11、cts to this CID. See section 2 for PIN example. The PIN procedure is for government purposes and does not constitute a requirement for the contractor. Figure 1 and table I are provided for configuration identification. SIZE ASIZE BFIGURE 1. Elbow, reducing, 90 degree. TABLE I. Dash numbers. Dash num

12、bers. Elbow, reducing (figure 1) Tube size, inches A x B -32 3/8 x 1/4 -43 1/2 x 3/8 -54 5/8 x 1/2 -65 3/4 x 5/8 -74 7/8 x 1/2 -75 7/8 x 5/8 -95 1 1/8 x 5/8 -97 1 1/8 x 7/8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59446A 3 TABLE I. Dash nu

13、mbers - Continued. Dash numbers. Elbow, reducing (figure 1) Tube size, inches A x B -117 1 3/8 x 7/8 -119 1 3/8 x 1 1/8 The PIN consists of the document identifier and a dash no. (see table I). The dash number denotes size in increments of 1/8 inch. PIN example AA59446-32: AA59446 - 32 Dash no. (see

14、 table I) Document identifier 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing ef

15、forts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials on the list should be mi

16、nimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these fuse plugs to DLA Land and Maritime under the Military Parts Control Advisory Group (MPCA

17、G) evaluation program, CAGE code 58536 should be used. 7.4 Sources of documents. FEDERAL REGULATIONS FAR Federal Acquisitions Regulations (FAR) (Copies of this document are available online at http:/www.acquisition.gov/comp/far/index.html from the U.S. Government Printing Office, 732 North Capital S

18、treet, NW, Washington D.C. 20401-0001.) Other Publications ASME INTERNATIONAL ASME B16.22 Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.)

19、7.5 Ordering data. The contractor order should specify the following: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59446A 4 a. CID document number, revision and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Cross r

20、eference data. See table II. TABLE II. Cross reference data. MS35922 Tube size, inches AA59446 MS35922-32 3/8 x 1/4 AA59446-32 MS35922-43 1/2 x 3/8 AA59446-43 MS35922-54 5/8 x 1/2 AA59446-54 MS35922-65 3/4 x 5/8 AA59446-65 MS35922-74 7/8 x 1/2 AA59446-74 MS35922-75 7/8 x 5/8 AA59446-75 MS35922-95 1

21、1/8 x 5/8 AA59446-95 MS35922-97 1 1/8 x 7/8 AA59446-97 MS35922-117 1 3/8 x 7/8 AA59446-117 MS35922-119 1 3/8 x 1 1/8 AA59446-119 7.7 National Stock Numbers (NSNs). The following is a list of identified NSNs assigned that correspond to this CID. This list may not be indicative of all possible NSNs as

22、sociated with this CID (see table III). TABLE III. NSNs. NSN Dash number 4730-00-173-1745 -32 4730-00-289-1269 -54 4730-00-469-1984 -43 7.8 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the c

23、hanges. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Custodians: Preparing activity: Army - GL DLA - CC Navy SH Air Force - 99 DLA - CC (Project 4730-2013-056) Review activities: Army - CE Navy - MC Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

24、se from IHS-,-,-A-A-59446A 5 NOTE: The activities listed above were interested in this document as the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-