DLA A-A-59453 A-2007 CAP SYNTHETIC MICROFLEECE《微羊毛鸭舌帽》.pdf

1、 Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP Standardization Team, 700 Robbins Avenue, Philadelphia, and PA 19111-5096. Since contact information can change, you may want to verify the

2、currency of the address information using Acquisition Streamlining and Standardization Information System (ASSIST) online database http:/assist.daps.dla.mil/. AMSC N/A FSC 8415 INCH-POUND A-A-59453A June 25, 2007 SUPERSEDING A-A-59453 16 January, 2004 COMMERCIAL ITEM DESCRIPTION CAP, SYNTHETIC MICRO

3、FLEECE The General Services Administration has authorized the use of this commercial item description, for all federal agencies. 1. SCOPE. This commercial item description covers the requirements for a synthetic microfleece cap that provides the necessary military appearance and functionality requir

4、ed by the Services. The material and design provide the environmental protection, low bulk, lightweight, durability and user comfort needed for wear in field and combat operations other than war. The cap is compatible with the military helmet and Extended Cold Weather Clothing System (ECWCS) parka h

5、ood. 2. CLASSIFICATION. The cap will be available in the following classes and sizes: Classes: Class 1 - Black Class 2 - Coyote Class 3 - Foliage Green 504 Sizes: Small/Medium or One Size Fits All Large/X-Large 3. SALIENT CHARACTERISTICS. The microfleece cap is a single ply construction in a bell sh

6、ape, pull-on style with a crown shaped of four equal sections joined together by darts of equal length and with a 4 + 1/8 inch wide hem that can be cuffed or worn down (see Figures 1 and 2). 3.1 Basic material. The basic material for the cap shall be a 100% no pill polyester circular knit terry with

7、 comfort stretch, double-sided, low micro velour (fleece) with moisture management properties (see 7.3). The color of the fabric shall be Black for Class 1, Coyote for Class 2 and Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59453A 2 Foliage G

8、reen 504 for Class 3. The material shall conform to the physical requirements specified in Table I. TABLE I. Material physical requirements Characteristics Requirement Test Method Fiber Content 100% polyester AATCC 20 or ASTM D 276 Yarn Denier (Ave, Pile) 1.3 dpf ASTM D 1907 Construction circular do

9、uble sided velour terry knit Weight, oz./sq. yd 5.7 + 0.6 ASTM D 3776 Thickness 0.6 psi (min) 0.070 ASTM D 1777 Air Permeability, cu ft/min/sq ft (min) 175 ASTM D 737 Colorfastness to: (minimum) Laundering (3 cycles) 3-4 AATCC 61- 2A, 1/, 2/ Crocking Wet 3.0 AATCC 8 3/ Dry 4.0 AATCC 8 3/ Light (40 h

10、rs or 170 KJ) 3-4 AATCC 16 OPT 1 or 3 Dimensional Stability - % (3 cycles) max. Wales: 4.5 Courses: 4.5 AATCC 135, III, A and the following parameters 4/ Water sorption Back side See 3.1.3 See 3.1.3 Wicking - Face Side See 3.1.3 See 3.1.3 1/ AATCC Evaluation Procedure 1, Gray Scale for Color Change

11、2/ AATCC Evaluation Procedure 2, Gray Scale for Staining. 3/ AATCC Evaluation Procedure 8, AATCC9-Step Chromatic Transference Scale 4/ Sample dimensions: 22 x 22 inches. AATCC 135 Table I 3, iii, Aiii. Use 18-inch marks to determine dimensional stability. 3.1.1 Visual Shade. The color and appearance

12、 of the material shall match the standard sample when viewed using the AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 + 200 K illumination of 100 + 20 foot candles, and shall be a good match to the standard sample u

13、nder incandescent lamplight at 2856 + 200K 3.1.2 Thread. Thread for needle and bobbin (looper) shall be commercial 100% textured, 2 or 3 ply, polyester thread, approximate Tex size 35, conforming to A-A-52095; or 2 or 3 ply cotton or polyester covered polyester core thread, approximate Tex size 35,

14、conforming to A-A-50199. The thread color shall be Black for Class 1, Coyote for Class 2 and Foliage Green 504 for Class 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59453A 3 3.1.3 Water sorption and Wicking Test. Fabric specimens shall be

15、conditioned in accordance with ASTM D 1776 and tested in that environment. The specimen size shall be 6-inches by 6-inches; three (3) separate specimens shall be used for each of the face side and back side tests. A fabric shall be considered passing only when tests on both the face side and the bac

16、k side meet the respective test pass/fail criteria on all individual specimens tested. The wicking test shall be conducted on the face side on the fabric and the sorption test shall be conducted on the back side of the fabric as specified in 3.1.3.1 3.1.3.2. 3.1.3.1 Face side wicking test. The test

17、specimen shall be laid flat on a glass plate with back side up (i.e., inner or skin surface when used in a garment). One (1) drop of 0.10 + 0.01 milliliters of distilled water at 70oF + 2oF shall be placed in the center of the test specimen using a pipette and a stopwatch/timer immediately started.

18、The test specimen shall then be immediately turned over on the glass plate with test specimen face side up. The diameter of the wicked water area (denoted by a darkened water mark) shall be measured at a total elapsed time of 10 seconds. The specimen shall be considered passing if the diameter of th

19、e wicked water area (darkened water mark) is equal to or greater than 1-3/16 inches. 3.1.3.2 Back side sorption test. The test specimen shall be laid flat on a glass plate with back side up (i.e., inner or skin surface when used in a garment). One (1) drop of 0.10 + 0.01 milliliters of distilled wat

20、er at 70oF + 2oF shall be placed in the center of the test specimen using a pipette and a stopwatch/timer immediately started. The water (denoted as a darkened water mark) shall be observed and the time for the water mark to disappear (water sorption, denoted as a lightened water mark approximating

21、the shade of the basic material) shall be recorded. The specimen shall be considered passing if the water sorption (disappearance of the darkened water mark) is 10 seconds or less. 3.2 Labels. Each cap shall have an identification label, size label and a care label. The labels may be combined. The i

22、dentification label shall contain the item description, contract number, fiber content information and the contractors name. The inscription shall have a minimum font size of 10 points. The inscription legibility, label, and label attachment shall last the expected life of the cap. If available, a b

23、asic material supplier care label and hang tag may be used, except the information must be as cited in paragraph 3.2.1 3.2.1 Care Label. The care label shall include the following information: Warm Wash Tumble Dry Low Or Line Dry DO NOT USE BLEACH DO NOT IRON 3.2.2 Bar-code label/tag. Each cap shall

24、 be individually bar-coded with a Type VI, Class 17, and Label/Tag of MIL-DTL-32075. The Label/Tag shall be located so that is completely visible on the item when it is folded and/or packaged as specified and shall cause no damage to the item. Provided by IHSNot for ResaleNo reproduction or networki

25、ng permitted without license from IHS-,-,-A-A-59453A 4 3.2.3 Label placement. The labels shall be securely attached to the cap and positioned as follows: (1) Care label and Identification label. At center back joining seam (+ inch) with top edge caught in the hem cover stitching. (2) Barcode label.

26、Attach to top of cap at center crown. (3) USMC label. When specified (see 7.4) the USMC label shall be placed at center back, on inside of cap as worn, with upper edge caught in hem stitching and remaining edges stitched to hem 1/16 to 3/16 inch from edge. 3.3 Toxicity. The finished cap shall not pr

27、esent a health hazard and shall show compatibility with prolonged, direct skin contact when tested as specified in 3.3.1. Chemicals recognized by the Environmental Protection Agency (EPA) as human carcinogens shall not be used 3.3.1 Toxicity Test. An acute dermal irritation study and a skin sensitiz

28、ation study shall be conducted on laboratory animals. When the results of the studies indicate the cap is not a sensitizer or irritant, a Repeat Insult Patch Test shall be performed in accordance with the Modified Draize Procedure (see 7.1.6) If the toxicity requirement (see 3.3) can be demonstrated

29、 with historical data, toxicity testing may not be required (see 7.4). 3.4 Patterns. The government shall furnish a pattern (see Table II) to maintain uniformity and consistency in manufacturing. Standard patterns provide an allowance of 3/8 inch for all joining seams. The government patterns shall

30、be used to create the contractors working patterns. Minor modifications are permitted to accommodate manufacturing procedures; however the design and finished measurements shall be maintained. TABLE II. Pattern parts. Material Nomenclature Cut Parts Polyester Fleece Cap, Synthetic Microfleece 1 3.5

31、Configuration. The following specifics are needed to provide uniform appearance; comfort and durability in use during field duties, and combat operations other than war. End item construction and appearance shall conform to Figure 1 and the finished dimensions listed in Table V to maintain configura

32、tion. 3.5.1 Seaming. The seams shall be consistent, exhibit a uniform appearance and conform to the ASTM D 6193 Stitch Types listed in Table III. All material edges shall not ravel. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59453A 5 TABLE I

33、II. Seams Seaming Area Seam Type Gage Stitch Type Join darts and close center back seam SSa-1 3/8 inch 504 Attach USMC label EFa-1 1/16 to 3/16 inch from edge. 301 Hem stitching and catching labels EFa-2 1/16 to 1/8 inch from edge 605 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged

34、to use recovered materials to the maximum extent practical, in accordance with 23.403 of the Federal Acquisition Regulation (FAR) 5. PRODUCT CONFORMANCE 5.1 Product conformance. The products provided shall meet the salient characteristics of this Commercial Item Description, and shall conform to the

35、 Government pattern/ producers own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance. 5.2 Visual examination. All of the visual properties listed below (see 5.2.1) and any other characteristics determined to af

36、fect the form, fit or function of the item as determined by the government representative shall be classified as a defect. 5.2.1 Defects. Any hole, cut, tear, run, needle chew or weakening defect in the material; any mend or patch; any shade variation within a part or between parts; any color not as

37、 specified; any puckered, distorted, pleated, wavy, twisted, irregular or open seams; any loose stitch tension resulting in loose seams; any seam type not as specified; any raw edges; any broken or missing thread or stitches; any spot or stain; any omitted component or any component not as specified

38、, any distorted, full, tight, or twisted components, excessive thread ends not trimmed or removed; any unpleasant odor; omitted, incorrect, illegible, labels; labels not attached as specified; bar codes omitted or not readable by scanner; illegible or omitted human-readable interpretation (HRI); bar

39、 code not visible on folded, packaged item; any damage caused by the bar code to the cap; and any dimensions and finished measurements not as specified shall be considered a defect. 5.3 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order. 5.5 Finished mea

40、surements. The cap shall conform to the dimensions specified (in inches) in Table IV: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59453A 6 TABLE IV. Cap finished measurements One Size Fits All Small/Medium Large/X-Large Tolerance Bottom Circu

41、mference 1/ 11 11 11-1/4 Cap height 2/ 10 10 10 Hem Width 3/ 4 4 4 Measurements shall be taken as follows: 1/ Cap shall be laid flat with hem edges even and measure from folded edge to folded edge at base of cap. 2/ Measure along center back joining seam from top of cap to bottom edge of hem. 3/ Mea

42、sure from bottom of cover stitch to base of hem. 6. PACKAGING 6.1 Packaging, packing and marking. Preservation, packing and marking shall be as specified in the contract or purchase order. 7. NOTES 7.1 Sources of documents 7.1.1 Copies of government documents are available online at http:/assist.dap

43、s.dla.mil/quicksearch/ or http:/assist.daps.mil or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. 7.1.2 AATCC Standards are available online at www.aatcc.org or from the American Association of Textile Chemists and Colorists, P.O. Box 122

44、15, Research Triangle Park, NC 27709-2215. 7.1.3 ANSI/ASQ standards are available online at http:/www.asq.org or from the American Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI 53203.) 7.1.4 ASTM Standards are available online at www.astm.org or from ASTM INTERNATIONAL, 100 Barr ha

45、rbor Drive, West Conshohocken, PA 19428-2959. 7.1.5 Federal Acquisition Regulations are available online at http:/acquisition.gov/far/index.html or by contacting the Superintendent of Documents at 202-512-1800. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

46、 IHS-,-,-A-A-59453A 7 7.1.6 Principles and Methods of Toxicology (fourth edition), A Wallace Hayes (editor), pp 1057 - 1060, 2001 are available from Taylor and Francis, Philadelphia PA or http:/www.taylorandfrancis.co.uk/. 7.2 Standard samples, patterns and drawings. 7.2.1 For standard samples and p

47、attern drawings, address the contracting activity issuing the invitation for bids or request for proposal. Standard samples are also available at DSCP through http:/warfighter.dla.mil under tab “Vendor Info” then “Specifications/Pattern Request” under “Special Instructions” provide color shade, roll

48、 number and solicitation/contract number. 7.3 Polartec 100 series; Micro Style 9118 or 9118M fleece material is known to meet the requirements of this document. 7.4 Ordering data. Purchasers should select the preferred options permitted herein and include the following information in procurement doc

49、uments (if applicable). a. Title, number, and date of this document. b. Class (color) and size required (see 2). c. Label requirement (see 3.2) d Toxicity requirement (see 3.3) e. Pattern for Cap (see 3.4). f. Acceptance Criteria (see 5.2) g. Packaging requirements (see 6.1). 7.5 Key words: Extended Cold Weather Clothing System (ECWCS) Headwear Polartec 100 Series