DLA A-A-59486 B-2010 PADLOCK SET (INDIVIDUALLY KEYED OR KEYED ALIKE).pdf

1、ASMC N/A FSC 5340 INCH-POUND A-A-59486B 3 May 2010 SUPERSEDING A-A-59486A 3 July 2001 COMMERCIAL ITEM DESCRIPTION PADLOCK SET (INDIVIDUALLY KEYED OR KEYED ALIKE) The General Services Administration has authorized the use of this Commercial Item Description for all federal agencies. 1. SCOPE: This Co

2、mmercial Item Description (CID) covers key operated, dead bolt padlocks intended for low security use. 2. SALIENT CHARACTERISTICS: 2.1 Padlock set furnished under this CID shall be individual key or key alike operated, double dead -bolt locking construction and shall conform with the requirements of

3、 ASTM F883, Type P01, Option A (captive key). Padlocks shall be supplied with chains and conform to the dimensions as specified in Table I and figures below. FIGURE 1. PADLOCK SET. Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia, ATTN: D

4、SCP-NASA, 700 Robbins Avenue, Philadelphia, PA 19111-5096 or email to dscpg&ispecommentsdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo repro

5、duction or networking permitted without license from IHS-,-,-A-A-59486B 2Table I. DASH # and DIMENSIONS DASH NUMBER A .100 B REF C .040 D E F MIN MAX MIN MAX MIN MAX 1 1.500 2.844 .281 .688 1.188 1.250 2.000 .594 .770 1.500 LONG SHACKLE 4.656 2.500 3.0002 1.750 2.968 .343 .750 1.250 1.250 2.000 .688

6、 .820 1.750 LONG SHACKLE 4.718 2.500 3.0002.2 Material. Shackle, case, spring and attachments shall be in accordance with the following: a. Brass or bronze conforming to ASTM B16/B16M, B30, B505/B505M, B584, or B770. b. Corrosion resistant steel, carbon steel or alloy steel as required in commercial

7、 practice unless otherwise specified. c. Spring shall be phosphor bronze conforming to ASTM B159/B159M. d. Steel shackle Shall be uniformly case hardened and shall meet the minimum desired grade requirements as specified for Forcing Tests of ASTM F883. e. Attachment clevis Shall be brass or steel wi

8、th zinc electroplated coating of ASTM B633. 2.3 Finish. Brass or bronze clear lacquer on exterior in accordance with commercial practice. Carbon steel or alloy steel shall be zinc or chromium electroplated conforming to ASTM B633 or B177. Prior to application of any coating, all exterior surface sha

9、ll have a smooth finish. Sharp edges and burrs shall be removed. The case surface shall have a smooth or tumbled finish for laminated construction. 2.4 Lubrication. Working parts shall be lubricated as needed with a lubricant normally used for the intended purpose. 2.5 Case. The case shall be either

10、 laminated or solid as specified (see 6.5) of the materials indicated for the type of padlock. If a solid steel case is specified, the case shall be uniformly case hardened steel with a hardness in the range of 40 to 50 on the Rockwell C scale (40-50 HRC). 2.6 Shackle. The shackle shall be “U” shape

11、d and may be either spring released or pull released. The diameter of the shackle shall be as specified in Table I. When steel shackle is specified, the shackle shall be uniformly case hardened. 2.7 Keying. All keys shall be captive (unremovable) in the cylinder when unlocked. When individually keye

12、d padlocks are specified, no key shall operate more than one (1) padlock per 50 padlocks. The key illustration depicts individually, master and grand master keys for padlocks as required. 2.7.1 Individually keyed padlock set. Individually keyed padlock set shall be equipped with two (2) keys per loc

13、k and two master keys per set. For padlock set that have more than one (1) group, the set shall be equipped with two (2) keys per lock, two master keys per group and two (2) grand master keys per set (see para. 4.2). Individually keyed padlocks shall have at least as many possible key changes as fol

14、low: DASH NUMBER 1 4,000 DASH NUMBER 2 10,000 2.7.2 Keyed alike padlock set. Keyed alike padlock set shall be equipped with key(s) per lock and key(s) per set as specified in the Part Identification Number (PIN) per 4.5b. 2.8 Chain. The chain supplied with the padlock shall conform to RR-C-271, Type

15、 II, Class 2 or 6 (brass or steel as applicable). The chain shall be nine (9) inches long one (1) link. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59486B 32.9 Marking. The markings “U.S.” and “SET” shall be .25 inch minimum size and can be l

16、ocated on either side of the padlock. 2.10 Padlocks, as a minimum, shall be able to withstand the testing requirements for Grade 2 of ASTM F883 with the following exception: a. For Surreptitious Entry Test, use Grade 1 in lieu of Grade 2 values for master key, grand master key, and keyed alike padlo

17、cks (Grade 2 for individually keyed padlocks only). b. Substitute the tensile force value per ASTM F883 with 800 pound-force (lbf) for dash number 1 padlocks and 2,000 lbf for dash number 2. 3. REGULATORY REQUIREMENTS. 3.1 The offerer/contractor is encouraged to use recovered materials to the maximu

18、m extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings,

19、specifications, standards, and the quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5. PACKAGING. 5.1 Preservation, packing and marking shall be as specified in the contract or orde

20、r. 6. NOTES. 6.1 Unless otherwise specified, all dimensions are in inches. 6.2 Master keyed means that the master key shall open all padlocks in a group, but shall not open locks of another group within a set of groups. Grand master keyed means that the grand master key shall open all padlocks withi

21、n all groups making up the set. 6.3 Unless otherwise specified in the contract or purchase order, packaging shall be in accordance with ASTM D3951. 6.4 In the event that the requirements of this document should conflict with ASTM F883, this document should take precedence. Provided by IHSNot for Res

22、aleNo reproduction or networking permitted without license from IHS-,-,-A-A-59486B 46.5 The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractors. The Part Identification Number (PIN) shall consist of the basic comme

23、rcial item description number followed by a dash number from Table I, plus other options as specified in the examples below (Two digits are required to specify the number of padlocks. Add “0” for number of padlocks less than 10. Add “L” behind a set or a specific group quantity designating the long

24、shackle.) : a. Example for individually keyed padlock set: AA59486 1 I B 40 20 15 05 L S Add “S” for solid case, omit for laminated case Add “L” behind a set or a specific group for long shackle, omit for standard shackle number of padlocks for group 3, omit for group = 2 group number of padlocks fo

25、r group 2, omit for group = 1 group number of padlocks for group 1, omit for group = 1 group number of padlocks in a set B = brass, S = steel (Designations “B” and “S” refer to the material to be used for both the lock body and the shackle.) Individually keyed padlocks Dash number fom Table IBasic C

26、ID number b. Example for keyed alike padlock set: AA59486 1 A B 10 L S2 E1 S Add “S” for solid case, omit for laminated case. number of key per lock (E1 = 1 key), omit for none number of key per set (S2=2 keys) Add “L” for long shackle, omit for standard shackle number of padlocks per set B = brass,

27、 S = steel (Designations “B” and “S” refer to the material to be used for both the lock body and the shackle.) Keyed alike padlocks Dash number fom Table IBasic CID number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59486B 56.6 Cross-referenc

28、e data. Padlock sets conforming to this CID, either laminated case or solid case, are interchangeable/substitutable with padlock sets conforming to MS21313G dated 10 Jul 1992. Table II. CROSS REFERENCE TABLE FOR ACTIVE MS PIN INDIVIDUALLY KEYED PADLOCKS Cancelled MS PIN Replacement CID PIN (Laminate

29、d Case) Replacement CID PIN (Solid Case) MS21313-2 AA59486-1IB05 AA59486-1IB05S MS21313-103 AA59486-1IB10 AA59486-1IB10S MS21313-6 AA59486-1IB13050503 AA59486-1IB13050503S MS21313-10 AA59486-1IB15 AA59486-1IB15S MS21313-12 AA59486-2IB15 AA59486-2IB15S MS21313-105 AA59486-1IB20 AA59486-1IB20S MS21313

30、-14 AA59486-1IB30 AA59486-1IB30S MS21313-18 AA59486-1IB30151005 AA59486-1IB30151005S MS21313-201 AA59486-1IB301510L05 AA59486-1IB301510L05S MS21313-108 AA59486-1IB40 AA59486-1IB40S MS21313-202 AA59486-1IB4020L1505 AA59486-1IB4020L1505S MS21313-111 AA59486-1IB50 AA59486-1IB50S MS21313-112 AA59486-1IB

31、50202010 AA59486-1IB50202010S MS21313-115 AA59486-1IB60 AA59486-1IB60S MS21313-117 AA59486-1IB70 AA59486-1IB70S MS21313-205 AA59486-2IB55351010L AA59486-2IB55351010LS MS21313-118 AA59486-1IB80 AA59486-1IB80S MS21313-32 AA59486-2IB80303020 AA59486-2IB80303020S MS21313-207 AA59486-2IB804520L15 AA59486

32、-2IB804520L15S MS21313-208 AA59486-2IB80501515L AA59486-2IB80501515LS MS21313-121 AA59486-1IB90 AA59486-1IB90S MS21313-122 AA59486-1IB100 AA59486-1IB100S KEYED ALIKE PADLOCKS Cancelled MS PIN Replacement CID PIN (Laminated Case) Replacement CID PIN (Solid Case) MS21313-50 AA59486-1AB05S2 AA59486-1AB

33、05S2S MS21313-52 AA59486-1AB05S2E1 AA59486-1AB05S2E1S MS21313-53 AA59486-1AB05LS2E1 AA59486-1AB05LS2E1S MS21313-163 AA59486-1AB06S3 AA59486-1AB06S3S MS21313-124 AA59486-1AB10S2 AA59486-1AB10S2S MS21313-126 AA59486-1AB20S2 AA59486-1AB20S2S MS21313-60 AA59486-1AB25S2E1 AA59486-1AB25S2E1S MS21313-128 A

34、A59486-1AB30S3 AA59486-1AB30S3S MS21313-130 AA59486-1AB40S4 AA59486-1AB40S4S MS21313-132 AA59486-1AB50S5 AA59486-1AB50S5S MS21313-137 AA59486-1AB100S10 AA59486-1AB100S10S Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59486B 66.7 Source of docum

35、ents. 6.7.1 FAR. The FAR may be obtained from the Regulatory Secretariat, 1800 F Street NW, Washington DC 20405 or online at http:/www.acqnet.gov. 6.7.2 ASTM Standards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or on

36、line at http:/www.astm.org. 6.8 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 6.9 Key words. Chain Laminated case Shackle Solid case 6.10 Changes from previous issue. The

37、 margins of this specification are marked with vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only, and the government assumes no liability whatsoever for any inaccuracies in these notation

38、s. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY ACTIVITIES: CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS Custodian: Army AR Preparing activty

39、: Navy YD DLA IS Air Force 99 Review activities: (Project 5340-2010-007 ) Army AV, CR, MI Navy MC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-